Kenmore 79641172210 washer Parts

Yes, on the Kenmore 79641172210 washer, many DIYers can replace the drain pump if they are comfortable removing panels, handling hose clamps, and working around water. We recommend following the step-by-step procedure in the 79641172210 washer manual and using the correct replacement part.

Before you start (safety and prep)

• Unplug the washer to prevent electric shock.
• Turn off both water supply valves.
• Have towels and a shallow pan ready; the pump area usually holds residual water.
• Take photos of wire connectors and hose routing before removal.
• Label connectors if more than one plug is removed.

What you typically replace on this model

For the Kenmore 79641172210, the compatible drain pump motor listed for this model is the drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T.

In many drain repairs, you may also inspect related drain components for cracks, clogs, or leaks:

Component	What it affects	When to replace/inspect
Drain pump motor	Draining and spin enable	Hums, won’t drain, intermittent drain
Drain pump filter drain hose	Draining and cleanout	Leaks at cleanout, brittle hose
Tub-to-pump hose	Flow to pump	Repeated clogs, pinholes, loose clamps

DIY steps (high-level)

1. Disconnect power and shut off water.
2. Access the pump area (panel removal varies by design; follow the manual).
3. Drain remaining water from the pump/filter area into a pan.
4. Remove the pump mounting screws, then release hose clamps and hoses.
5. Transfer wiring to the new pump, reinstall hoses and clamps, then reassemble.
6. Run a rinse and drain cycle and check carefully for leaks.

Why it matters

A weak or failed drain pump can cause no-drain symptoms, standing water, and spin problems. Replacing the pump promptly helps prevent odor, leaks, and cycle interruptions.

Last updated: January 2026

A bad drain pump on our Kenmore washer model 79641172210 usually shows up as water that will not drain, a spin cycle that stops with water still in the tub, or a loud humming/grinding sound when the washer should be pumping out. Use the 79641172210 washer manual to confirm the drain and spin behavior for your cycle selections.

Common signs the drain pump is failing

Look for these symptoms during the drain portion of the cycle:

• Washer will not drain or drains very slowly
• Standing water left in the tub at the end of the cycle
• Humming/buzzing from the lower front area but little or no water flow
• Grinding/rattling noises (often from debris contacting the impeller)
• Intermittent draining (works sometimes, fails other times)
• Washer stops mid-cycle and will not complete the final spin

Quick checks before replacing parts

These checks help separate a clogged drain path from a failed pump motor:

• Verify the drain hose is not kinked, crushed, or shoved too far down the standpipe
• Check for a clog at the pump filter area (coins, hair pins, lint, small socks)
• Confirm the standpipe or laundry sink is not backing up
• Listen during drain: a steady hum with no draining often points to a jammed or failed pump
• If the washer drains but very slowly, inspect the pump-to-tub hose for blockage

If you determine the pump motor is not moving water (or is noisy and binding), the compatible replacement for this model is the drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T.

What the symptoms usually mean

Symptom	Most likely cause	What we check next
Hums but will not drain	Jammed impeller or failed pump motor	Clear debris; replace pump if still stuck
Drains slowly	Partial clog in filter/hose	Clean filter; inspect tub-to-pump hose
Loud grinding during drain	Debris in pump or worn pump	Inspect pump cavity; replace if noisy after cleaning
Stops with water in tub	Drain problem triggering a stop	Check drain path; then pump motor

Why it matters

A weak or failed drain pump can leave water in the tub, prevent high-speed spin, and cause repeat mid-cycle stoppages. Catching it early can prevent odors, poor cleaning, and extra wear on the drive system.

Last updated: January 2026

A Kenmore washer like model 79641172210 typically lasts 10 to 12 years with normal household use and basic maintenance. Actual life depends most on load size, detergent use (HE), installation, and how quickly leaks, drain issues, or vibration problems are corrected.

What affects lifespan the most

• Overloading (stresses the drive system, tub bearings, and suspension)
• Poor draining (can overwork the drain pump and leave standing water)
• Hard water and excess detergent (buildup can cause odors and component wear)
• Unlevel installation (increases vibration and can shorten bearing and shock life)
• Ignoring small leaks (water damage can spread to wiring and controls)

For model-specific care and cleaning routines, follow the maintenance guidance in the 79641172210 washer manual.

Quick maintenance checklist (helps you reach 10 to 12 years)

• Run a monthly tub-clean cycle (or hot cycle) to reduce residue.
• Leave the door slightly open between loads to limit odor and mildew.
• Clean the dispenser drawer and inlet screens periodically.
• Check pockets for coins and debris to protect the drain system.
• Level the washer and re-check if it starts vibrating more than usual.

Common wear items vs. “end of life” repairs

Symptom	Often a maintenance/part fix	Often a major repair decision
Won’t drain	Drain pump or filter area	Repeated drain failures plus control issues
Loud rumble in spin	None	Tub bearing/spider related wear
Door won’t lock	Door lock/strike	Wiring or control board faults

If your washer is not draining or is leaving water behind, the drain system is a common place to start; the drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T is one compatible component used on this model.

Why it matters

Knowing the typical lifespan helps us decide whether to invest in a repair (like a drain pump, door boot, or inlet valve) or plan for replacement when multiple high-wear systems start failing close together.

Last updated: January 2026