Kenmore Elite 11026962500 washer Parts

For Kenmore Elite washer model 11026962500, the model number is the key identifier we use to match the correct parts and service information. On this washer, you can find the model and serial label under the washer lid; record the full model number exactly as shown for accurate part fit.

On Kenmore model 11026962500, the model and serial number label is located under the lid.

• Lift the washer lid fully
• Look along the underside rim area near the opening
• Find the label that lists Model and Serial
• Write the model number exactly (all digits, no spaces)
• Keep it with your purchase date for future reference (service, parts, maintenance)

For the official location and “product record” section, use the 11026962500 owner's manual.

Many Kenmore model numbers use a prefix that identifies the original manufacturer, followed by digits that identify the design series and specific variation. For this washer, the model number is shown as 11026962500 (often you will see “110.” as the leading identifier on Kenmore laundry products).

Even small digit changes can mean different timers, lid switches, pumps, or drive components. Using the complete model number helps us match the correct replacement part the first time.

• Prevents ordering the wrong version of a part
• Improves fit and wiring/connector compatibility
• Helps match diagrams and troubleshooting steps
• Speeds up identifying common wear items

If you are ordering common mechanical parts for this model, examples include the washer lid switch assembly WP8318084 and the washer drain pump WP3363394. You can also search by model number on Sears PartsDirect.

Last updated: February 2026

To force your Kenmore Elite washer model 11026962500 to drain, select a Drain/Spin (or Spin Only) cycle and start it; if the washer will not drain, unplug it and clear the drain path (hose and pump) so water can exit normally. Use the steps in the installation guide to confirm the drain hose is installed correctly.

• Try Drain/Spin first: Cancel the cycle, then choose Drain/Spin and press Start.
• Reset power: Unplug the washer for 1 minute, plug back in, then try Drain/Spin again.
• Gravity drain (manual drain): Unplug the washer, then lower the drain hose into a shallow pan or floor drain to let water siphon out.
• Check for a kinked hose: Rotate the hooked end to eliminate kinks; do not force extra hose down into the standpipe.
• Clear the pump inlet: If the tub is full and you hear the motor but no draining, a clog at the pump is likely; the common replacement is the washer drain pump WP3363394.

A drain problem is often a drain hose installation issue. For model 11026962500, the drain hose should be secured but still allow an air gap so the washer can pump out without backflow.

• Keep the hooked end of the hose; do not straighten it.
• Do not shove excess hose into the standpipe.
• Do not lay excess hose in the bottom of the laundry tub.
• Secure the hose to the tub leg or standpipe with a strap so it cannot pop out.

A restricted drain hose or a failing drain pump can leave water in the tub, cause poor spin performance, and lead to odors. Correct hose routing and a clear pump path protect floors from leaks and help the washer complete the cycle.

You can order replacement parts for your washer from the parts list for model 11026962500, or search by model on Sears PartsDirect.

Last updated: February 2026

For the Kenmore Elite washer model 11026962500, a “hard reset” is a power reset: unplug the washer (or switch off the breaker) for 1 minute, then restore power and restart the cycle. This clears many temporary control and cycle issues; use the 11026962500 owner's manual for model-specific operating steps.

• Turn the Cycle Control knob to Off.
• Unplug the washer for 60 seconds (or turn off the circuit breaker).
• Plug it back in (or turn the breaker on).
• Close the lid.
• Select a cycle and pull out the Cycle Control knob to start.

On this washer style, “resetting” is often about correcting a condition that stops the cycle (lid not sensed, not draining, or an out-of-balance load).

• Lid not detected: Make sure the lid closes firmly; if the washer stops when you open the lid and will not restart when closed, the lid switch can be the issue.
• Not draining: Check the drain hose for kinks and confirm the standpipe or laundry tub is not backing up.
• Vibration or walking: Leveling problems can interrupt spinning; the installation instructions call for leveling the washer and tightening the front leveling-foot nuts.

A power reset clears a stalled timer or control state, but it will not fix a mechanical failure (drain pump, motor coupling, lid switch). Matching the symptom to the right check prevents repeat shutdowns and protects the gear case and drive system.

Last updated: February 2026

Yes, it’s worth repairing a Kenmore washer when the fix restores reliable operation for less than the cost of replacing the machine. For Kenmore Elite model 11026962500, repairs are especially worthwhile when the problem is a common wear item (like a lid switch, drain pump, or motor coupling) rather than major basket or gearcase damage.

Use these practical checkpoints before spending money on parts or labor:

• Compare total repair cost to replacement cost (parts plus labor, if you’re hiring it out).
• Confirm the failure is isolated (one clear symptom, not multiple unrelated issues).
• Prioritize common, high-success repairs (switches, pumps, couplings, springs).
• Check for secondary damage (leaks, burning smell, metal shavings, repeated tripping).
• Factor in downtime (a simple part swap is usually faster than shopping and installing a new washer).

These are frequent failure points on many Kenmore top-load designs and typically deliver a strong “repair payoff”:

Repair is still possible, but replacement usually makes more sense when you see any of these:

• Gearcase failure with loud grinding and poor performance (often higher parts cost, more labor)
• Basket or tub damage (rust-through, cracks, severe wobble with multiple worn components)
• Repeated leaks that have damaged wiring, bearings, or the floor
• Multiple major parts needed at once (for example, gearcase plus basket plus suspension)

A targeted repair can extend the life of your Kenmore Elite washer for years because many breakdowns are caused by a single worn mechanical part. Your 11026962500 owner’s manual also includes operating and loading guidance (balanced loads, avoiding overloading, proper bleach use) that helps prevent repeat failures.

• Match parts by model 11026962500 and symptom.
• Use the parts list for this model to confirm fit.
• If you want to search beyond the parts shown, use Sears PartsDirect and search by model number.

Last updated: February 2026

The Kenmore Elite washer model 11026962500 is a top-load washer; its usable load size is best set by how freely items move during agitation rather than a single number. For the most accurate model-specific specs, check the 11026962500 installation guide and the 11026962500 owner's manual.

Use these practical rules to match the washer’s real-world capacity and avoid out-of-balance issues.

• Load items loosely; do not pack or compress laundry
• Keep the load below the top row of holes or the top of the basket ring
• Mix large and small items to help balance the spin
• For bulky items (comforters, jackets), wash one at a time
• If the washer struggles to spin or bangs, reduce the load and redistribute

This helps you estimate what “full” means if you are comparing washers or planning laundry room space.

Correct load sizing improves cleaning, reduces vibration, and helps prevent wear on drive and drain components. Overloading commonly contributes to poor agitation and slow or incomplete draining; if you are troubleshooting draining, the washer drain pump WP3363394 is a common service part.

If you need replacement parts for model 11026962500, order from the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026