Kenmore Elite 79551823410 refrigerator Parts

Most Kenmore Elite refrigerators, including model 79551823410, last 12 years on average. With consistent maintenance (clean airflow, tight door seals, and a healthy water system), a typical real-world range is 10 to 15 years.

Refrigerator life depends most on compressor run time, airflow through the condenser area, and how well the doors seal.

• Average: 12 years
• Common range: 10 to 15 years
• Often replaced sooner when: cooling problems, sealed-system issues, or repeated control failures occur
• Often lasts longer when: coils stay clean and temperatures stay stable

These steps reduce strain on the compressor and help prevent common side-by-side refrigerator problems.

• Keep condenser airflow clear (vacuum dust from the grille and lower rear area)
• Confirm doors close fully and gaskets seal all the way around
• Keep freezer vents unblocked so cold air can circulate
• Replace the water filter on schedule to protect the dispenser and ice maker
• Set stable temps (avoid frequent warm-ups from overloading or long door openings)

For model-specific care and cleaning intervals, follow the 79551823410 owner's manual.

A refrigerator that runs hotter or longer than normal wears out the compressor and control components faster. Simple upkeep helps your Kenmore Elite refrigerator hold safe food temperatures while reducing expensive repairs.

Last updated: February 2026

Kenmore Elite refrigerator model 79551823410 is a full-size refrigerator; most Kenmore side-by-side units in this series are about 33 inches wide, about 31 to 34 inches deep, and about 68 inches tall. For the exact cabinet and door-swing dimensions for your unit, use the 79551823410 owner's manual.

We recommend measuring your refrigerator and comparing it to the specification drawings in the manual.

• Measure width at the widest point (often the doors or handles)
• Measure height from floor to top hinge cover area
• Measure depth with doors closed (and separately with handles if installed)
• Allow at least 24 inches of clearance in front so the doors can open fully
• Plan for about 2 inches of clearance around the sides and top for airflow

These are common real-world ranges for Kenmore Elite refrigerators similar to model 79551823410.

Getting the size right prevents installation problems like doors that cannot open fully, poor airflow that hurts cooling performance, and water line kinks for the ice maker and dispenser.

The manual also calls out installation conditions that affect performance.

• Install where ambient temperature stays 55°F to 110°F
• If your model uses a water filter, supply water pressure should be 40 to 120 psi
• If you are connecting water, choose a location with easy access to the shutoff valve

Last updated: February 2026

To reset your Kenmore Elite refrigerator model 79551823410, we recommend doing a power reset: unplug the refrigerator (or switch off the circuit breaker) for about 5 minutes, then restore power and set the refrigerator and freezer controls back to your normal temperatures.

• Full power reset: Unplug for 5 minutes, then plug back in.
• Breaker reset: Turn the refrigerator circuit breaker OFF for 5 minutes, then ON.
• Control reset after service: After restoring power, reset the temperature controls to the desired setting (the manual notes controls should be reset after reconnecting power). See the owner's manual for control and operating details.

• Confirm the display is responsive and not locked (some functions require unlocking first).
• Verify temperature settings were restored (common targets are 37°F fresh food and 0°F freezer).
• Make sure air vents are not blocked by food packages.
• Listen for fans and compressor to start within a few minutes.
• If the issue is water or ice related, confirm the filter is seated and not overdue; the correct filter for this model is the Kenmore refrigerator water filter 9490 ADQ73613402.

A reset gets the control board back to a clean start, but cooling still takes time to stabilize.

A proper reset clears minor control glitches after a power interruption and ensures the thermostat and electronic controls are set correctly. If the refrigerator still will not run after a reset, troubleshooting should continue with power supply, door switch, and control issues using the owner's manual.

Last updated: February 2026

Kenmore model numbers are read left to right; the first 3 digits identify the manufacturer code, and the remaining digits narrow down the exact design and feature set. For your Kenmore Elite refrigerator model 79551823410, matching the full model number in the 79551823410 owner's manual ensures you get the correct parts and instructions.

Most Kenmore model numbers follow this pattern:

• Prefix (first 3 digits): manufacturer code (who built it for Kenmore)
• Middle digits: product family and base design
• Ending digits: engineering revisions, color, or feature variations
• Full model number: the only reliable way to match parts like a water filter, control board, or ice maker

Common locations on Kenmore side-by-side refrigerators include:

• Inside the fresh food compartment on a side wall
• On the ceiling area near the lights
• On the door frame when the door is open
• On a rating plate behind the crisper drawers (varies by design)

Even small model-number differences can change fitment for items like a compressor, dispenser components, or water system parts.

If you are ordering a water filter for this refrigerator, use a model-matched part listing such as the Kenmore refrigerator water filter 9490 ADQ73613402 to avoid compatibility issues.

Using the exact Kenmore model number prevents returns and delays, and it helps us pull the correct diagrams for troubleshooting and repairs (cooling, ice maker, dispenser, and control issues).

Last updated: February 2026