Kenmore 11076455110 electric dryer Parts

Your Kenmore dryer’s model number is printed on the appliance data label; once you find it, match it exactly (all digits) to order the right parts and confirm fit. For this page, the model number format looks like 11076455110.

Where to find the model number label

Check these common spots on Kenmore electric dryers:

• Inside the dryer door opening on the cabinet frame
• On the back panel of the dryer
• Along the door opening edge near the latch area
• Near the lint screen housing (some designs place the label nearby)
• On the lower front frame behind the toe panel (less common)

What the model number looks like (and why it matters)

Kenmore model numbers are usually a long string of numbers (sometimes with a prefix like 110.). Use the full model number exactly as shown on the label.

Quick guide

What you see on the label	What it tells you	What to do next
A long number like 11076455110	The exact dryer model	Use it to look up diagrams and parts
A shorter number or partial match	Not specific enough for parts	Keep searching for the full label
A serial number	Production identifier, not the model	Do not use it for part lookup

Tips to avoid ordering the wrong part

When you write down the model number, we recommend:

• Copying every digit in order (no spaces)
• Taking a clear photo of the label for reference
• Using the model number (not the serial number) when searching
• Verifying the part category before buying (belt, motor, door switch, lint screen)

If your dryer is squealing, not tumbling, or not starting, the model number helps us match the correct common wear parts such as the whirlpool dryer drum belt 341241 or the dryer door switch W10820036.

Why it matters

Kenmore dryers share similar styling across many years, but internal parts can differ by model series. Using the exact model number ensures the right fit, correct wiring style, and proper drum and drive compatibility.

Last updated: February 2026

To replace the thermistor on your Kenmore electric dryer model 11076455110, unplug the dryer, access the blower housing or heater housing area, disconnect the thermistor wires, remove the mounting screw(s), and install the new sensor in the same position. Reassemble and test a timed dry cycle.

Safety first

• Unplug the dryer (or switch off the breaker) before opening any panels
• Let the heater housing cool completely
• Wear cut-resistant gloves around sheet-metal edges
• Take a quick photo of wire placement before disconnecting anything
• If you smell burning or see melted wiring, stop and repair the wiring before running the dryer

Where the thermistor is usually located

On most Kenmore 110-series electric dryers, the thermistor mounts on or near the blower housing (airflow side). Some versions place it on the heater housing. You will typically reach it by removing the rear panel.

Quick access checklist

• Remove lint screen and clear lint from the chute area
• Remove the rear panel screws and lift the panel off
• Find the blower housing (near the exhaust outlet) and look for a small sensor with 2 wires

Replacement steps (typical)

1. Disconnect power.
2. Remove the rear panel.
3. Locate the thermistor and pull off the wire connectors (grip the connector, not the wire).
4. Remove the mounting screw(s) and take the thermistor off.
5. Install the new thermistor in the same orientation and tighten the screw(s).
6. Reconnect wires firmly.
7. Reinstall the rear panel.
8. Run Timed Dry, High Heat for 5 to 10 minutes and confirm steady heat and normal cycling.

If you are troubleshooting a “no heat” or “overheating” complaint

A failed thermistor is only one possibility. Airflow problems are just as common.

Symptom	Most common cause	What to check first
Long dry times	Restricted venting	Lint screen, vent hose, outside hood
Overheating / burning smell	Blocked airflow	Lint chute, blower wheel area
Runs but no heat	Heating circuit issue	Power supply (240V), heater, thermostats

For model-family diagnostics, we use the same style of fault-code guidance found in Kenmore 110 series electronic control model dryer error codes.

Why it matters

The thermistor helps the control regulate temperature. If it reads wrong, the dryer can underheat (long dry times) or overheat (fabric damage and thermal shutdowns). Fixing airflow and replacing a bad sensor restores normal cycling.

Last updated: February 2026

A Kenmore electric dryer like model 11076455110 typically lasts 13 years with normal household use. Keeping airflow strong (clean lint screen, clear venting) and replacing wear items like the belt when needed helps you reach that lifespan.

Typical lifespan and what affects it

Most dryers fail early from heat and airflow issues or from normal wear in moving parts.

• Heavy loads and frequent cycles shorten life
• Restricted venting overheats the heater and thermostats
• Worn drum support parts increase friction and strain the motor
• Running with a slipping belt can damage the drum drive system
• Regular lint removal reduces fire risk and improves drying performance

Quick maintenance checklist (high impact)

• Clean the lint screen before every load
• Inspect and clean the exhaust duct regularly (especially long runs)
• Avoid overloading; it strains the motor and drum supports
• Listen for squealing, thumping, or scraping and address it early
• If the drum stops turning or slips, check the belt and idler system

Common wear items for this model

If your 11076455110 is noisy, not tumbling, or taking longer to dry, these are frequent culprits:

Symptom	Common cause	Example part to check
Drum will not turn	Broken or stretched belt	Whirlpool dryer drum belt 341241
Loud rumble or vibration	Worn blower wheel or loose drive parts	Dryer blower wheel WP694089
Overheating or poor temperature control	Weak cycling thermostat or airflow restriction	Thermostat WP694674

Why it matters

A dryer that runs hot or with extra friction wears out the motor, heater circuit, and drum supports faster. Fixing airflow problems and replacing a worn belt or blower wheel is usually cheaper than running the dryer until a major component fails.

Last updated: March 2026