Kenmore 11018202790 washer Parts

A Kenmore washer typically lasts 10 to 15 years with normal household use. For your Kenmore 11018202790, regular cleaning, correct loading, and fixing small issues early (drain, spin, fill problems) are the biggest factors in reaching the high end of that range; see the owner's manual.

What affects washer lifespan most

• Load size and balance: chronic overloading and unbalanced loads strain the drive system and suspension.
• Water quality and detergent use: too much detergent can cause residue buildup and extra wear.
• Drain performance: slow draining makes the pump work harder and can leave standing water.
• Spin system wear: slipping or noisy spin components accelerate damage.
• Leaks: even small leaks can lead to corrosion and bearing issues.

Signs your washer is nearing end of life

• Loud grinding, rumbling, or repeated burning smells during agitation or spin
• Frequent no-spin or weak-spin complaints even after redistributing the load
• Water not draining consistently (or draining very slowly)
• Oil or grease marks under the washer (often tied to drive system wear)
• Repeated leaks around the tub area

Common wear parts that can extend service life

Replacing a failed wear part is often the difference between a quick fix and a full replacement.

Symptom	Common part to check	Example part for this model
Won’t drain or drains slowly	Drain pump, drain path	Washer drain pump WP3363394
Agitates but won’t spin (or vice versa)	Motor coupling, clutch	Coupling 285753A or clutch 285785
Loud spin, poor spin, tub movement	Suspension components	Washer suspension spring WP63907

Why it matters

A washer that is maintained and repaired early usually runs quieter, cleans better, and avoids secondary damage (for example, a drain issue that leads to odors, leaks, or motor strain). Following the care and operating guidance in the owner's manual helps you get the full expected lifespan.

Last updated: February 2026

To unclog the drain hose on your Kenmore washer model 11018202790, unplug the washer, remove the hose from the standpipe (and from the washer if needed), clear the blockage, then reinstall the hose so it is clamped securely and not kinked. Use the owner's manual drain-hose connection steps to prevent leaks afterward.

Quick steps to clear a clog

• Unplug the washer to prevent the motor from running unexpectedly.
• Pull the hooked end of the drain hose out of the standpipe or laundry tub.
• Check for kinks, crushed sections, or a tight fit in the standpipe (a tight fit can cause drain problems).
• If the clog is near the end, flush the hose with hot water; a hot water and vinegar soak can help loosen residue.
• If the clog is deeper, disconnect the straight end at the bottom drain outlet and flush from that end.
• Reinstall the hose: twist and push it fully onto the washer drain connector until it reaches the ribbed stop, then position the clamp over the marked “CLAMP” area.

Reinstall it correctly (prevents leaks and repeat clogs)

The manual procedure for this model matters because a loose or mispositioned clamp can cause leaks.

What to check	What “right” looks like	What it prevents
Clamp position	Clamp sits about 1/4 inch from the hose end, then over the marked clamp area	Leaks at the washer outlet
Hose routing	No sharp bends; hook rotated to eliminate kinks	Slow drain, no-drain, siphoning
Standpipe fit	Hose is not sealed or taped; there is an air gap	Cycle stuck draining, backflow

When a clog points to a part problem

If the hose is clear but the washer still will not drain or leaves wet loads, the drain pump can be jammed or failing. For this model, the replacement pump is the washer drain pump WP3363394.

Why it matters

A restricted drain hose can cause “won’t drain/won’t spin” symptoms, longer cycle times, and water leaks. Correct hose height and a loose standpipe fit also help prevent siphoning and repeat drain issues.

Last updated: February 2026

To reset your Kenmore washer model 11018202790, we recommend doing a simple power reset: stop the cycle, turn the washer off, unplug it for 1 to 5 minutes, then plug it back in and restart the cycle using the timer knob as normal (push in to stop, pull out to run). See the owner's manual for the exact stop and restart steps for this model.

Quick reset steps (power reset)

• Push the Cycle Selector (Timer) knob in to stop the washer.
• Turn the control to Off (if your console has an Off position).
• Unplug the power cord from the grounded outlet.
• Wait 1 to 5 minutes.
• Plug the washer back in.
• Set the cycle by turning the timer knob to the right, then pull the knob out to start.

If it still will not start after resetting

These checks solve most “won’t start” complaints on this style of Kenmore top-load washer:

• Confirm the outlet has power (reset the breaker if needed).
• Do not use an extension cord.
• Make sure the timer is lined up on a cycle; turn it slightly to the right, then pull to start.
• Close the lid fully (an open lid can prevent spin and drain).
• If the washer is overloaded, remove a few items and try again.

What “reset” can and cannot fix

Symptom	Reset helps most when	Likely next step if it returns
Controls seem stuck or cycle won’t advance	Timer paused or control got out of sequence	Re-set the cycle and restart using the timer knob
Won’t drain or won’t spin	Temporary control interruption	Check drain hose height/kinks; reduce suds
Stops mid-cycle	Overload or pause in cycle	Wash smaller loads; allow pause to finish

Why it matters

A power reset clears a temporary control hang-up and gets the timer sequence back on track. If the washer repeatedly will not drain or spin, the issue is usually mechanical or installation-related (for example a kinked drain hose or excessive suds), not something a reset can permanently correct.

Last updated: February 2026

Kenmore washer model 11018202790 is a full-size, top-load washer. For fit planning, the manual notes this washer’s cabinet width is either 24 inches or 27 inches (width varies by model configuration); confirm your exact cabinet measurements in the 11018202790 owner's manual.

What “size” usually means for this washer

Most customers mean one of these:

• Cabinet width (space between walls or in a closet)
• Overall height (including the control console)
• Depth (front-to-back clearance for hoses and lid opening)
• Capacity class (this manual family covers standard to extra-large capacity designs)

Model-specific sizing detail from the manual

The installation section calls out a key planning spec:

Spec	What to expect	Why it matters
Cabinet width	24 in. or 27 in.	Determines whether it fits in a recessed area or closet
Side clearance (recommended)	1 in. each side	Helps reduce vibration and sound transfer
Closet ventilation	Openings at top and bottom of door	Helps prevent heat and moisture buildup

How we recommend measuring your exact washer

Measure before building shelving, ordering a pan, or moving the washer into a tight space:

• Measure width across the cabinet at the widest point.
• Measure depth from the front edge to the farthest rear point (often hoses add depth).
• Measure height to the top of the console.
• Add room for lid swing and hose bend radius.

Why it matters

Correct dimensions prevent common install problems like a closet door that will not close, kinked drain hoses, and excessive vibration from a too-tight side-to-side fit.

Last updated: February 2026