Kenmore 11082870820 washer Parts

A Kenmore washer typically lasts 10 to 15 years. For your Kenmore model 11082870820, lifespan depends most on load size, how often you run it, and whether wear items (like the drive coupling, pump, and suspension parts) are replaced when symptoms first show up.

Typical lifespan by use level

Most washers land in the same general range, but usage changes the outcome.

• Light use (1 to 3 loads/week): often closer to 15 years
• Average use (4 to 7 loads/week): typically 10 to 15 years
• Heavy use (8+ loads/week): often closer to 8 to 12 years

What you notice	What it usually means	Common next step
Won’t drain or leaves water in tub	Drain restriction or failing pump	Check hoses, then consider replacing the water pump WP3363394
Agitates poorly or “slips”	Worn agitator drive parts	Inspect and replace the agitator dog 80040 if worn
Loud during spin, weak spin	Drive train wear (coupling, clutch, gear case)	Inspect coupling and clutch; replace as needed

How to make a Kenmore washer last longer

These habits reduce strain on the motor, clutch, and gear case.

• Keep loads balanced; mix large and small items
• Avoid overloading; it accelerates clutch and coupling wear
• Use the right amount of detergent to reduce residue and drag
• Check fill and drain hoses for kinks and slow draining
• Level the washer to reduce vibration and suspension wear
• Address new noises early (grinding, squealing, banging)

Why it matters

Washer failures are often caused by a few high-wear components. Replacing a relatively small part early (for example, a pump or agitator drive part) helps protect bigger, higher-cost assemblies like the gear case and drive basket.

Last updated: February 2026

Kenmore washer model numbers use a consistent pattern: the first 3 digits identify who built the washer for Kenmore, the next group identifies the base design, and the final digits show the specific version. Your model number 11082870820 follows that same format.

What each section of a Kenmore model number means

Most Kenmore washer model numbers break down like this:

• Prefix (first 3 digits): manufacturer identifier (who produced the washer for Kenmore)
• Middle digits: base model or platform (the core design family)
• Ending digits: variation details (features, color, revision, or production run)

How this helps when buying parts

We use the full model number to match parts that fit your exact washer configuration. Even small suffix changes can affect items like the lid switch, water inlet valve, or drive system.

Common part categories that can vary by model version include:

• Agitation and drive parts (agitator components, clutch, coupling)
• Drain components (pump and hoses)
• Fill components (water inlet valve)
• Safety and control parts (lid switch)
• Tub and basket hardware (drive block, spanner nut, gasket)

Quick examples for model 11082870820

Here are a few common replacement parts we list for Kenmore 11082870820 (examples of why the exact model matters):

What you are fixing	Part you may need	What it affects
Agitator not moving properly	Agitator dog 80040	Agitator “ratcheting” action
Washer will not spin or agitates poorly	Coupling 285753A	Motor-to-transmission drive connection
Washer will not drain	Water pump WP3363394	Draining water out of the tub

Why it matters

Reading the model number correctly prevents ordering the wrong Kenmore washer parts and saves time on repairs. Using the full 11082870820 model number is the most reliable way to match the correct fit.

Last updated: February 2026

The exact cubic-foot capacity for Kenmore washer model 11082870820 is not listed in the model details we have here; most Kenmore 110-series top-load, direct-drive washers of this style typically fall in the about 3.0 to 3.5 cu. ft. range, depending on the tub and basket used.

How to estimate capacity (quick, accurate method)

If you need a working number for load sizing, you can estimate tub volume by measuring the inside of the wash basket.

• Unplug the washer for safety.
• Measure the inside diameter of the basket (in inches).
• Measure the usable depth from the bottom to the highest fill line you normally use (in inches).
• Use the formula below.
• Convert cubic inches to cubic feet.

Formula

• Cubic inches = 3.1416 × (diameter ÷ 2)² × depth
• Cubic feet = cubic inches ÷ 1728

Typical capacity guidance for this Kenmore style

For Kenmore 110-series, agitator-equipped top-load washers, capacity usually lands in a narrow band. Use this as a practical guide for detergent dosing and load size.

Capacity (cu. ft.)	What it usually means	Typical load examples
3.0 to 3.3	Standard to large	Mixed everyday laundry, 1 queen sheet set
3.4 to 3.5	Large	Bulkier towels, small comforter (check balance)
3.6+	Extra-large	Larger bedding loads (model-dependent)

Why it matters

Capacity affects cleaning and wear. Overloading reduces agitation and rinsing, increases out-of-balance spinning, and can accelerate wear on drive components like the coupling 285753A and clutch 285785.

If your goal is “what size load can I wash?”

Use these practical rules for a Kenmore agitator top-load washer:

• Load loosely to the top of the basket; do not pack items down.
• Keep a palm-width gap at the top so clothes can circulate.
• Wash bulky items in pairs (two towels, two jeans) to balance.
• If the washer struggles to spin or bangs, reduce the load size.
• If draining is slow, check for pump or hose restrictions; the water pump WP3363394 is a common service part.

Last updated: February 2026

Yes, repairing a Kenmore washer is worth it when the fix restores reliable washing and spinning for less than the cost of replacing the machine. For Kenmore model 11082870820, many common failures are repairable with standard mechanical parts, so a targeted repair often delivers years of additional service.

How we decide if repair makes sense

We use three practical checks before buying parts:

• Symptom severity: No-spin, no-agitate, or no-drain problems are often straightforward; cabinet rust, severe leaks, or repeated electrical failures are not.
• Repair cost vs. replacement: If parts plus labor stay well below a comparable new washer, repair wins.
• Overall condition: If the tub, basket, and cabinet are solid and the washer has not been flooding, repairs tend to hold.

Common repairs that are usually worth doing on this model

These are frequent wear items on many Kenmore top-load designs; they are typically cost-effective compared with replacement:

• Agitation issues (worn dogs or cam): agitator dog 80040, agitator cam 285748
• No-agitate or loud grinding at start (drive coupling): coupling 285753A
• Won’t drain or leaves water in tub (pump): water pump WP3363394
• Spin problems or burning smell (clutch): clutch 285785

Quick symptom-to-part guide

What it’s doing	Most likely area	Part on this page to check
Agitator moves weakly or “ratchets”	Agitator drive	Agitator dog 80040
Motor runs but washer won’t agitate/spin	Motor-to-transmission drive	Coupling 285753A
Hums, won’t drain, or drains slowly	Drain system	Water pump WP3363394
Spins poorly, especially with heavier loads	Spin drive	Clutch 285785

Why it matters

A repair-first approach is often the fastest way to get dependable wash performance back, especially when the failure is a single wear part (coupling, pump, clutch, or agitator components). Replacing the right part also prevents secondary damage, such as overheating the drive motor or stressing the gear case.

Last updated: February 2026