Kenmore 66513293K113 undercounter dishwasher Parts

Your Kenmore dishwasher model number is printed on the rating label inside the door area. On model 66513293K113, you will find the label just inside the dishwasher door, typically along the left-hand side, and it lists both the model and serial number.

Where to look (fast checklist)

• Open the dishwasher door fully.
• Look along the inner edge of the tub opening.
• Check the left-hand side first (most common location).
• Find a sticker or metal tag labeled Model and Serial.
• Write the model number exactly as shown (letters and numbers matter).

What the label helps you do

Having the exact model number lets us match the correct Kenmore parts and diagrams for your dishwasher, including common repair items like the drain pump, water inlet valve, and rack components.

What you need	Where it appears	Why it matters
Model number (example: 66513293K113)	Rating label inside the door	Ensures correct part fit and instructions
Serial number	Same label	Helps identify production details for some parts

Why it matters

Kenmore model numbers can look similar, and a single digit difference can change the correct dishwasher drain hose, heater, or control parts. Using the rating label prevents ordering the wrong replacement.

Helpful next step

Use the model number you find to reference the 66513293K113 owner’s manual for operating details and the 66513293K113 installation guide for installation and connection requirements.

Last updated: February 2026

To hard reset your Kenmore dishwasher model 66513293K113, we recommend using the control-panel reset sequence (often called a “cancel/drain reset”) and then restoring power if needed. This clears a stuck cycle and reboots the electronic control so you can start a fresh wash.

Quick reset steps (most common)

• Press Cancel/Drain once, then wait about 2 minutes for the drain to run.
• If the dishwasher has a Heated Dry and High Temp option, press them in an alternating pattern (for example: Heated Dry, High Temp, Heated Dry, High Temp) until the indicators change, then wait 3 minutes.
• If the controls are unresponsive, turn power off at the breaker for 1 minute, then turn it back on.
• Close the door fully and select a new cycle.
• If the unit immediately returns to the same problem, check for a drain or fill issue before repeating resets.

If it will not reset: check the two most common causes

A “reset” often fails because the dishwasher is protecting itself from a drain or fill problem.

• Standing water in the tub: check the sink/disposer connection and the drain path; a blocked hose can prevent the control from completing cancel/drain.
• No water entering: confirm the shutoff valve is on and the supply line is clear.

Parts that commonly relate to reset-like symptoms

Symptom after reset	What to check	Example part for this model
Won’t drain, hums, or stops mid-cycle	Drain path, pump operation	Dishwasher drain pump WPW10348269
Fills slowly or not at all	Water supply, inlet screen/valve	Dishwasher water inlet valve W11175771
Drains but leaves soil, poor wash	Filter and circulation	Dishwasher filter W10872845

Why it matters

A hard reset is useful for clearing a frozen keypad or canceling a stuck cycle, but it does not fix the underlying cause. If the dishwasher cannot drain or fill correctly, the control will often repeat the same behavior right after the reset.

Helpful reference

For model-specific control behavior and cycle cancellation details, use the 66513293K113 owner’s manual.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher like model 66513293K113 is worth it when the problem is isolated (draining, filling, heating, rack hardware) and the tub and door seal are in good shape; a targeted repair typically restores performance without the cost and hassle of replacement. Use the 66513293K113 installation guide and 66513293K113 owner’s manual to confirm basic checks and safe service steps.

Quick way we decide: repair vs replace

• Repair when the dishwasher still fills, washes, and the leak risk is low.
• Repair when the failure is a common service part (pump, valve, heater, spray arm, rack parts).
• Replace when the tub is damaged, the unit has repeated major failures, or multiple expensive parts are needed at once.
• Replace when the door will not align or seal even after centering and leveling.
• Repair when you want to avoid cabinet fit issues; installation requires proper clearances and secure mounting.

Common repairs that are usually “worth it”

These are frequent, straightforward fixes on many Kenmore undercounter dishwashers:

Symptom	What to check first	Part that often fixes it (if failed)
Won’t drain or leaves water	Kinked/clogged drain path, disposer plug, drain loop	Dishwasher drain pump WPW10348269 or dishwasher drain hose 8269144A
Won’t fill or fills slowly	Water supply valve on, inlet screen debris	Dishwasher water inlet valve W11175771
Poor cleaning	Loading, spray arm holes blocked, filter area dirty	Dishwasher spray arm WPW10491331 or dishwasher filter W10872845
Dishes not drying	Heated dry setting, rinse aid, heater circuit	Dishwasher heater W10703867

Installation and “hidden cost” checks

A dishwasher that is loose, unlevel, or rubbing the cabinet can feel “broken” even when parts are fine. From the install guidance, we focus on:

• Confirm the unit is secured to the countertop or side-mounted so it does not shift when the door opens.
• Verify corner clearance (2 inches minimum between door and wall/cabinet in corner installs).
• Make sure the floor is level; use shims if needed and secure them so the dishwasher cannot shift.
• Ensure drain and water lines do not contact the motor or legs.

Why it matters

A well-chosen repair saves money, avoids re-installation risks (clearance, leveling, mounting), and keeps your kitchen setup consistent. A poor repair choice usually happens when the real issue is installation alignment or multiple major components failing together.

Last updated: February 2026

Common problems we see with the Kenmore 66513293K113 dishwasher include not starting (door not fully latched or power issue), poor draining, poor cleaning from spray issues, and weak drying when rinse aid is low. Use the 66513293K113 installation guide checks to quickly rule out basic setup and start problems.

Quick checks first (fast, no parts)

• Confirm the door closes tightly and latches; a loose latch prevents starting.
• Check the house breaker or fuse.
• Verify the cycle is selected correctly, then press Start/Resume.
• Make sure the water supply valve is turned on.
• If Start/Resume flashes, close the door within 3 seconds after pressing Start/Resume.

Most common symptoms and what usually causes them

Symptom	Most common cause	What to do next
Won’t start	Door not latched, breaker/fuse tripped, cycle not set	Do the quick checks above; then follow the start-up steps in the 66513293K113 owner’s manual
Won’t drain	Clogged hose/air gap, drain pump issue	Check for kinks/clogs; inspect the dishwasher drain pump WPW10348269 if the motor hums but water stays
Dishes still dirty	Clogged filter, blocked spray arm holes, weak wash action	Clean the filter area; inspect/clean the dishwasher spray arm WPW10491331
Poor drying	No rinse aid, heater issue	Fill rinse aid; if water is cold at end of cycle, test the dishwasher heater W10703867

Why it matters

These dishwashers rely on proper latching, correct water supply, and clear circulation and draining paths. A simple issue like a door that is not fully latched or low rinse aid can look like a major failure, so the basic checks save time and prevent unnecessary part replacement.

Last updated: February 2026

On Kenmore dishwasher model 66513293K113, a “Start/Resume” button that won’t start a cycle is usually caused by the door not latching fully, a missed 3-second door-close window after pressing Start/Resume, or a power supply issue. Use the checks in the 66513293K113 installation guide to confirm basic operating conditions.

Quick checks that fix most “won’t start” problems

• Press Start/Resume, then close the door within 3 seconds; if you miss the window, press Start/Resume again and close the door promptly.
• Make sure the door is closed tightly and latched (a loose latch prevents the cycle from starting).
• Check the home circuit breaker or fuse for the dishwasher circuit.
• Confirm the cycle is set correctly (a cycle must be selected before Start/Resume will run).
• Verify the water supply valve is turned on.

What to do next if the button still doesn’t respond

If the console lights work but the dishwasher will not start, focus on the door-latch circuit and the control inputs.

Common causes and what you’ll notice

What’s happening	What you’ll see	What to check first
Door not fully latched	Start/Resume light flashes or cycle won’t begin	Door closure, latch alignment, strike position
Power interruption	No response or intermittent response	Breaker, junction box connection, power cord (if used)
Control not accepting input	Buttons light but won’t start	User interface and control connections

Parts that are often involved

• Door latch or latch switch (not listed in the parts shown for this model; check the door/latch section in the parts list)
• Electronic control (if the control is not sending start commands)
• User interface (if the Start/Resume key is not registering)

Why it matters

The dishwasher is designed to prevent starting unless the door is safely latched and the cycle is set correctly. That interlock protects against leaks and ensures the fill and wash sequence begins normally.

Last updated: February 2026