Kenmore 10656722600 side-by-side refrigerator Parts

Most Kenmore side-by-side refrigerators are about 32 to 36 inches wide; your Kenmore model 10656722600 is in this common size range. For the exact cabinet width and required clearances for door swing and airflow, we use the measurements listed in the 10656722600 owner's manual.

Typical width ranges (what you can expect)

Side-by-side refrigerators are built in a few standard widths. Use this as a quick sizing guide before you measure your opening.

• 32 to 33 inches: narrower side-by-side models
• 35 to 36 inches: most common full-size side-by-side models
• 36+ inches: larger or specialty configurations

Refrigerator type	Typical width	Best for
Narrow side-by-side	32 to 33 in.	tighter kitchen cutouts
Standard side-by-side	35 to 36 in.	most existing 36-in. openings
Oversize side-by-side	36+ in.	larger kitchens, more capacity

How to measure width the right way

We recommend measuring both the refrigerator and the space so you avoid surprises with trim, hinges, and door swing.

• Measure the cabinet width (main box), not just the doors
• Measure at the widest point (often near hinges)
• Measure your opening in three places (top, middle, bottom)
• Confirm you have room for door swing next to walls or cabinets
• Plan for ventilation space: the manual calls for 1/2 inch on each side and at the top, and about 2 inches minimum next to a fixed wall (varies by setup)

Why it matters

Width affects more than fit. If the refrigerator is too tight in the opening, airflow can suffer and doors may not open fully, which can lead to temperature issues and everyday usability problems.

Last updated: February 2026

The most common problems we see on Kenmore refrigerators like model 10656722600 are cooling issues, water or ice dispenser problems, leaks, door sealing problems, and unusual noises. Many of these come down to airflow (dirty coils or a failing fan), defrost system trouble, or worn water-system components; our owner's manual troubleshooting section is a good first stop.

Common symptoms and what usually causes them

• Not cooling or warm temperatures: dirty condenser coils, evaporator fan issues, defrost failure (ice buildup), or control problems
• Ice maker not making ice: water supply issue, clogged filter, bad inlet valve, or ice maker failure
• Water dispenser slow or not dispensing: clogged filter, frozen water tube, or inlet valve problem
• Water leaking or puddles: clogged defrost drain, loose water line, or door not sealing
• Noises (buzzing, clicking, rattling): fan blade hitting ice, failing fan motor, or compressor start components

Quick checks we recommend before replacing parts

1. Confirm power and controls: the manual notes to verify the outlet works and controls are on; after a new install, allow 24 hours to cool fully.
2. Check airflow: keep vents clear inside; clean condenser coils (dust buildup is a top cause of poor cooling).
3. Look for frost buildup: heavy frost on the freezer back wall points to a defrost problem.
4. Inspect the door seal: gaps or a torn gasket cause moisture, frost, and temperature swings.
5. Verify water supply: make sure the refrigerator is connected to a cold water pipe; flush the system after changing a filter.

Parts that commonly solve these problems (for model 10656722600)

Problem area	Common fix	Example part on this model
Poor water flow, bad ice production	Replace clogged filter	Genuine Kenmore refrigerator water filter EDR3RXD1
No water to dispenser/ice maker	Replace inlet valve	Refrigerator water inlet valve W10408179
Frost buildup, warm temps	Check defrost thermostat	Refrigerator defrost bi-metal WPW10225581
No ice production	Replace ice maker	Refrigerator ice maker WPW10190965
Warm temps, noise in freezer	Inspect fan blade/ice	Refrigerator evaporator fan blade WP2169142

Why it matters

Cooling, ice, and water issues often share the same root causes: restricted airflow, ice buildup from defrost trouble, or low water flow from a clogged filter or failing inlet valve. Fixing the underlying cause prevents repeat failures and helps protect food temperatures.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10656722600, the model number is printed on the appliance identification label inside the fresh food (refrigerator) compartment. We typically see it on a label along the side wall near the crisper drawers or around the door opening; confirm the exact spot in the 10656722600 owner's manual.

Common label locations to check first

• Inside the refrigerator section on the left or right side wall
• On the frame around the refrigerator door opening (near the gasket)
• Near the crisper pan area (above or beside the drawers)
• Behind the base grille area (less common for the model tag, but worth a quick look)

How to find it fast (no tools)

1. Open the refrigerator door and look around the door opening (the cabinet frame).
2. Scan the side walls at eye level, then lower near the crisper pans.
3. Use a flashlight and wipe condensation or dust off the label so the numbers are readable.
4. Write down both the model number and serial number exactly as shown.

What the label usually includes

Item on label	What it’s used for	Why you need it
Model number (example: 10656722600)	Identifies the exact design	Ensures parts diagrams match your refrigerator
Serial number	Identifies production run	Helps confirm compatible revisions of parts

Why it matters

Kenmore side-by-side refrigerators can look identical across multiple model numbers. Using the exact model number helps us match the correct parts list and diagrams for items like the water filter, ice maker, or water inlet valve.

Last updated: February 2026