Installation guide
Owner’s manual
Error Codes
How do I tell what model my Kenmore dryer is?
To tell what model your Kenmore dryer is, we look for the model number on the appliance ID label (a sticker or metal plate). On Kenmore model 11079133411, it’s most often found around the door opening or on the cabinet; once you have it, matching parts and instructions is straightforward.
Where to find the model number label
Check these common locations first (use a flashlight and wipe dust off the label):
- Inside the dryer door opening on the front frame
- On the back panel of the dryer cabinet
- Along the door opening edge near the latch area
- On the lower front cabinet area (behind a small access panel on some builds)
- Near the lint screen housing (some designs place the label close by)
What the model number looks like (and why it matters)
Kenmore dryer model numbers are typically all digits and often start with a prefix like 110. The full model number is what we use to pull the correct gas burner parts, drum support parts, and control components.
| What to capture | Example for this dryer | Why it matters |
|---|---|---|
| Model number | 11079133411 | Ensures correct part fit and diagrams |
| Serial number | (varies) | Helps identify production run details |
| Fuel type | Gas dryer | Confirms ignition and gas valve parts |
Tips to avoid ordering the wrong part
Before you shop for items like a belt, thermal fuse, or igniter, we recommend:
- Write the model number exactly as shown (all digits, no spaces)
- Take a clear photo of the label for reference
- Use the model number when checking procedures in the 11079133411 owner’s manual
- If you’re troubleshooting heat issues, confirm you have a gas model before replacing ignition parts like the igniter 279311
Why it matters
The model number is the fastest way to match the right Kenmore gas dryer parts and the correct troubleshooting steps. Even small model variations can change the drum support roller style, control panel layout, or burner/ignition components.
Last updated: February 2026
What is the average lifespan of 11079133411?
A Kenmore gas dryer like model 11079133411 typically lasts 13 years with normal household use and routine vent and lint maintenance. Keeping airflow strong and heat controls working correctly is the biggest factor in reaching that lifespan.
What affects lifespan the most
- Venting: long runs, crushed flex duct, or clogged exterior hood shortens life
- Lint buildup inside the cabinet and blower housing increases heat stress
- Overloading strains the drum support rollers and belt
- High heat cycles used constantly wear thermostats and fuses faster
- Gas ignition issues (igniter, coils, radiant sensor) cause repeated no-heat cycling
Maintenance checklist (best return for the effort)
- Clean the lint screen every load; replace a damaged screen such as dryer lint screen (white) W10859086
- Verify strong airflow at the outside vent while the dryer runs
- Clean the full vent line at least yearly (more often with pets)
- Keep the drum turning smoothly; squealing or thumping points to roller wear
- Follow the cleaning and care steps in the owner's manual
Common wear items and what they do
| Symptom | Likely wear area | Example part for this model |
|---|---|---|
| Squealing, rumbling | Drum support | Dryer drum support roller WPW10314173 |
| Long dry times | Airflow or blower | Dryer blower wheel WP697772 |
| No heat or heat cuts out | Heat safety/control | Thermal fuse W10909685 |
Why it matters
A dryer that runs hot or can’t move air dries slower, overheats components, and trips safety devices. Fixing airflow and early wear symptoms helps the 11079133411 dry faster, run safer, and reach its full service life.
Last updated: March 2026
What replacement parts are most commonly needed for the 11079133411?
For Kenmore gas dryer model 11079133411, the most commonly replaced parts are the heat safety parts, gas ignition parts, and drum support parts. These items address the most frequent symptoms: no heat, heat cutting out, loud squealing, thumping, and long dry times.
Most common replacement parts (and what they fix)
- Thermal fuse W10909685: dryer overheats and stops heating (often caused by a clogged vent)
- Dryer thermal cut-off kit WP8573713: heat shuts down due to high temperature conditions
- Igniter 279311: burner won’t light, no heat
- Dryer valve coil kit 279834: burner lights once then quits, intermittent heat
- Dryer drum support roller WPW10314173: squealing, rumbling, thumping as the drum turns
- Belt-4 rib, W10849499: drum won’t turn or slips
- Dryer blower wheel WP697772: weak airflow, long dry times, rattling noise
Quick symptom-to-part guide
| What you notice | What to check first | Common part(s) |
|---|---|---|
| Runs but no heat | Ignition and safety circuit | Igniter, coils, thermal fuse |
| Heats then stops | Coils overheating or airflow restriction | Coil kit, venting, thermal cut-off |
| Loud squeal or thump | Drum support wear | Support roller, repair kit |
| Takes too long to dry | Venting and blower | Blower wheel, lint screen |
Before you order: 5 checks that prevent repeat failures
- Clean the entire exhaust vent run and outside hood
- Confirm the lint screen is intact and seated; use dryer lint screen (white) W10859086 if yours is torn or warped
- Make sure the dryer is not pushed back crushing the vent
- Verify the drum turns smoothly by hand (unplugged)
- Use the wiring diagram and troubleshooting steps in the installation guide
Why it matters
Replacing the failed part is only half the fix on a gas dryer. Restoring airflow and correcting the root cause (usually vent restriction or drum friction) prevents blown fuses, weak heat, and repeat breakdowns.
Last updated: March 2026
