Kenmore 10653552201 refrigerator Parts

For Kenmore side-by-side refrigerator model 10653552201, cleaning the condenser coils means safely removing dust and pet hair so the refrigerator can transfer heat properly. Dirty coils make the compressor run longer and can reduce cooling performance; follow the steps in the 10653552201 owner's manual.

• Unplug the refrigerator or disconnect power at the breaker.
• Pull the refrigerator straight out to avoid kinking the water line.
• Remove the base grille (most side-by-sides have coils behind or underneath it).
• Use only nonflammable cleaners on and around the refrigerator.
• Keep water and spray cleaners away from electrical parts.

• Vacuum loose dust from the grille area and coil surface using a brush attachment.
• Use a coil brush to loosen packed lint, then vacuum again.
• Clean the floor area under the unit so dust does not get pulled back in.
• Reinstall the base grille firmly when finished.
• Restore power and confirm the refrigerator is running normally.

When condenser coils are dirty, airflow and heat transfer drop. The manual notes that dirty condenser coils make the motor work harder and run longer; cleaning the coils helps efficiency, temperature stability, and can reduce noise from extended run time.

If you are also seeing weak ice production or dispenser issues, coil cleaning is a good first step, but water supply problems can also be involved. For prevention steps, use how to prevent water dispenser and ice maker problems.

Last updated: February 2026

To replace the ice maker in your Kenmore side-by-side refrigerator model 10653552201, we shut the ice maker off, remove the ice bin or bucket for access, swap the ice maker assembly, then restore power and water and verify ice production. Follow the exact access steps in the 10653552201 owner's manual.

• Unplug the refrigerator or switch off the circuit breaker.
• Turn off the household water supply shutoff valve.
• Empty the ice container; melt stuck ice with warm water if needed.
• Keep a plastic utensil handy to clear any ice jam at the ejector.

1. Turn the ice maker off:
   • Style 1: lift the wire shutoff arm to OFF (up) until it clicks.
   • Style 2: slide the ON/OFF control to OFF (right).
2. Remove the ice bin or bucket to reach the ice maker.
3. Remove mounting screws, then disconnect the wiring harness/connector.
4. Install the new ice maker, reconnect the harness, and secure the screws.
5. Reinstall the bin or bucket fully (the dispenser may not work if it is not seated).
6. Restore water and power; turn the ice maker back on.

For model 10653552201, a common replacement is the refrigerator ice maker assembly 2198597.

Turning the ice maker off correctly and fully reinstalling the bin or bucket prevents dispenser problems and lets the automatic shutoff work as the container fills.

Last updated: February 2026

On a Kenmore 10653552201 side-by-side refrigerator, a “bad compressor” usually shows up as poor or no cooling along with unusual compressor behavior (repeated clicking, running constantly, or not running at all). Before condemning the compressor, we verify airflow, control settings, and normal operating sounds using the 10653552201 owner's manual.

• Confirm the refrigerator and freezer controls are set correctly for the room conditions.
• Make sure air vents are not blocked by food packages (blocked vents can mimic sealed-system problems).
• If your model has digital controls, turn the unit OFF then ON to reset.
• Listen for normal sounds: a high-pitched or pulsating sound can be normal as the compressor and fans adjust.
• Note whether the unit runs longer than an older refrigerator; high-efficiency designs often do.

These signs typically mean the compressor is not pumping refrigerant correctly or is not starting reliably:

• Refrigerator runs most of the time but temperatures stay warm
• Repeated clicking from the start device area (start attempt then shutdown)
• Compressor is very hot to the touch after trying to run (use caution)
• Little to no vibration or sound from the compressor when it should be running
• Frost pattern issues on the evaporator (often requires removing panels to inspect)

A compressor diagnosis is confirmed with electrical and performance checks.

The compressor is part of the sealed refrigeration system; misdiagnosing it can lead to unnecessary cost. Many “not cooling” complaints are caused by blocked vents, control settings, or normal longer run times described in the manual.

Last updated: February 2026

Most Kenmore side-by-side refrigerators are about 32 to 36 inches wide; for your Kenmore 10653552201, the exact cabinet width is listed in the 10653552201 owner's manual and the 10653552201 installation guide. Plan for extra clearance so the doors can swing fully and airflow stays unrestricted.

Side-by-side refrigerator widths commonly fall into these buckets:

• 32 to 33 inches: space-saving models
• 35 to 36 inches: most full-size side-by-sides
• 36+ inches: larger capacity or premium configurations

Even if the cabinet width fits, you still need room around it. The Kenmore side-by-side installation guidance calls for ventilation space and added side clearance near walls for door swing.

• Allow about 1/2 inch on each side and at the top for airflow
• If installed next to a fixed wall, allow about 2 inches minimum on the hinge side (varies by setup) so the door can open
• Leave extra space behind the unit if you have an ice maker water line
• Measure with doors closed and also confirm door swing clearance

Use a tape measure and check more than one spot.

• Measure the cabinet (main box) width at the front
• Measure the widest point (often the hinge area)
• If you are fitting into a cutout, measure the opening in three places (top, middle, bottom)
• Confirm whether you are measuring with or without handles

Width affects more than fit. Proper clearance helps the refrigerator cool efficiently, prevents door interference, and reduces the chance of vibration noise or warm spots from restricted airflow.

Last updated: February 2026

The cubic-foot capacity for Kenmore refrigerator model 10653552201 is listed in the specifications section of the product literature; the fastest way to get the exact total capacity (and the refrigerator vs. freezer breakdown) is to check the 10653552201 owner's manual.

In the manual, capacity is typically shown as total volume and may also be split by compartment.

• Check the “Specifications” or “Product data” section
• Look for “Total capacity” (overall cubic feet)
• If shown, note “Refrigerator capacity” and “Freezer capacity” separately
• Use the model and serial label inside the fresh food compartment to confirm you are matching the correct model

Most Kenmore 106-series side-by-side refrigerators are in the low-to-mid 20 cu. ft. range total. Your exact number depends on the specific configuration and interior layout.

Cubic feet helps you compare replacement refrigerators, plan storage, and understand why usable space can feel smaller when bins, shelves, and an ice bucket are installed.

If you are trying to reclaim freezer room or troubleshoot ice production, the common refrigerator ice maker problems and solutions guide covers common causes such as low water flow, a frozen fill tube, or a misaligned ice bin.

Last updated: February 2026

Most Kenmore refrigerators average 10 to 15 years of service life with normal household use. For Kenmore model 10653552201, consistent maintenance (cleaning, good door sealing, and prompt repairs) is what most often determines whether it lands closer to 10 years or pushes beyond 15.

• 10 to 15 years: common for many refrigerators with average maintenance
• 15 to 20 years: achievable when the sealed system stays healthy and upkeep is consistent
• Under 10 years: more likely when airflow is restricted (dirty condenser), doors do not seal, or cooling issues go unaddressed

We recommend focusing on the items that reduce compressor run time and prevent moisture and frost problems:

• Clean the condenser area regularly (dust buildup makes the refrigerator work harder).
• Keep door gaskets clean so doors close and seal properly.
• Maintain steady temperatures (avoid frequent warm-ups from long door openings).
• Keep air vents inside the refrigerator and freezer unblocked.
• Replace failed cooling or defrost components promptly (frost buildup can strain the system).

For model-specific care and cleaning steps, follow the schedule and instructions in the 10653552201 owner's manual.

A refrigerator that runs longer and harder than it should (because of dirty coils, air leaks, or frost restriction) typically has a shorter lifespan. Good airflow and a tight door seal reduce wear on major components like the compressor and fans.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10653552201, the model number is printed on the model and serial number label located on the inside wall of the refrigerator (fresh food) compartment. Use that label to record both the model and serial number for parts and service.

• Open the refrigerator (fresh food) door, not the freezer door
• Look along the inside walls of the fresh food compartment
• Check near the crisper area and side walls where labels are commonly placed
• Use a flashlight; the label can be small and easy to miss
• Write down the full model number and serial number exactly as shown

We use the model number to ensure you get the correct Kenmore refrigerator parts (for example, an ice maker assembly, water inlet valve, or door gasket) because similar-looking side-by-side models can use different components.

For the exact label location notes and record-keeping section, check the 10653552201 owner’s manual.

Last updated: February 2026