Kenmore 41748102700 washer Parts

A Kenmore washer typically lasts 10 to 15 years. For your Kenmore 41748102700 front-load washer, regular maintenance (proper loading, cleaning, and keeping it level) helps you reach the high end of that range and reduces wear on key parts.

Most washer life comes down to how hard it works and how well it is maintained.

• Loads per week: more cycles equals faster wear
• Overloading: strains the motor, tub, and suspension
• Out-of-balance spinning: increases stress on shocks and bearings
• Water quality and detergent use: excess suds and buildup shorten component life
• Basic care: cleaning the door area and using correct settings improves reliability

These symptoms often show up as a washer approaches the end of its service life:

• Frequent drain problems or slow draining
• Door that will not lock or unlock reliably
• Excessive vibration or banging during spin
• Leaks around the door opening
• Intermittent no-start or cycle stopping mid-cycle

If your washer is otherwise in good shape, replacing a failed wear part can extend its usable life.

Knowing the 10 to 15 year average helps you decide whether to repair or replace. If the washer is within that range and the issue is isolated (like a drain pump or door lock), a targeted repair often restores normal operation and prevents secondary damage.

For cycle choices, loading guidance, and operating steps (including door lock behavior and adding a garment), follow the 41748102700 owner's manual. For setup and long-term reliability items like placement and installation basics, use the 41748102700 installation guide.

If you need to purchase replacement parts for this model, we list compatible parts on this page; you can also search by model number on Sears PartsDirect.

Last updated: February 2026

To hard reset your Kenmore washer model 41748102700, we recommend a power reset first: unplug the washer (or switch off the breaker) for 1 minute, then restore power and start a cycle. This clears many control glitches without changing your saved cycle settings; see the 41748102700 owner's manual for model-specific control behavior.

• Power reset (best first step): Unplug for 60 seconds, then plug back into a grounded outlet.
• Stop and clear the current cycle: Press Pause/Cancel twice to stop the washer.
• Unlock the controls (if Control Lock is on): Press and hold OPTIONS and Select together for about 10 seconds until the Control Lock light turns off.
• Door lock patience reset: If you interrupted a spin, wait 2 to 3 minutes for the door lock to release; do not force the door.
• Run a quick verification cycle: Start a simple cycle and confirm the washer fills, tumbles, drains, and spins normally.

A reset helps when the control is confused, but it will not fix a mechanical failure (drain, door lock, or vibration issue). Check these common causes:

• Washer will not start: door not fully closed or door lock not engaging
• Will not drain: drain hose routing issue or a failing pump
• Excessive shaking: load out of balance or worn suspension
• Controls unresponsive: intermittent power, stuck keys, or a failing control

Resetting correctly prevents unnecessary part replacement and avoids forcing the door lock. On the 41748102700, the washer is designed to keep the door locked during the cycle, and it can take a few minutes to unlock after a spin interruption.

We list model-matched replacement parts for Kenmore 41748102700 on this page, and you can also search by model number on Sears PartsDirect.

Last updated: February 2026

Kenmore washer model numbers are structured so the first 3 digits identify the manufacturer, the next set of digits identifies the base design, and the final digits indicate feature or production variations. For your Kenmore washer model 41748102700, the 417 prefix is the key manufacturer identifier.

Most Kenmore washer model numbers break down like this:

• Prefix (first 3 digits): manufacturer code (example: 417)
• Middle digits: base model or platform family
• Ending digits: version details such as color, control style, or production run

For model 41748102700, you will typically use the full model number when ordering parts, but the 417 prefix is especially helpful when you are comparing parts diagrams across similar Kenmore-built platforms.

We recommend confirming the full model number from the appliance ID tag before ordering parts.

• Open the door and check around the door opening
• Look along the front frame behind the door
• Check the rear panel if you do not see it at the door
• Write down the full model number, including any leading zeros

For diagrams, safety notes, and operating details tied to this platform, use the 41748102700 owner's manual.

A single digit difference can change the correct door lock, control board, or drain pump. Using the exact model number helps ensure the part fits and the wiring connectors match.

If you are troubleshooting a symptom and shopping parts, these are often model- and revision-sensitive:

• Door lock and door strike alignment
• Drain and spin components
• Electronic control and motor control
• Door boot (bellows) sealing surfaces

If the washer will not start because the door will not lock, the door lock switch 131763256 is a common related part for this model family.

You can order replacement parts for Kenmore 41748102700 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

Yes, repairing a Kenmore washer is worth it when the fix restores reliable operation for less than the cost of replacing the machine. For Kenmore model 41748102700, common repairs like a door lock, drain pump, or shock absorbers often bring the washer back to normal performance.

Use these practical checkpoints before you spend money on parts or labor:

• Total repair cost vs. replacement cost: if the repair is clearly cheaper, repair wins.
• What failed: wear items (pump, door lock, shocks, hoses) are usually good repair candidates.
• How the washer is behaving: repeated no-drain, no-spin, or door-won’t-lock issues point to specific parts.
• Condition of the tub and cabinet: severe rust, heavy leaks, or structural damage usually pushes toward replacement.
• Downtime: if you need a fast fix, in-stock parts can make repair the quickest path.

These are frequent failure points on front-load washers and are available for this model:

• Door won’t lock or cycle won’t start: door lock switch 131763256
• Won’t drain or leaves water in the tub: water pump 137221600
• Excessive shaking or banging: shock absorber 5304485917

A targeted repair prevents repeat breakdowns and protects major components (motor, control boards, tub) from extra strain caused by poor draining, out-of-balance spinning, or a door that will not latch.

1. Confirm the symptom and any display indicators using the 41748102700 owner's manual.
2. Run a complete cycle after any repair and check for leaks and proper operation (the installation instructions recommend a full test cycle).
3. If you’re ordering parts beyond what’s listed for this model, search by model number on Sears PartsDirect.

Last updated: February 2026

Yes. Kenmore Elite is Kenmore’s higher-end lineup; it typically adds more premium features, quieter operation, and upgraded styling compared with standard Kenmore models. Your Kenmore washer model 41748102700 is a Kenmore-branded washer; use the 41748102700 owner's manual to confirm the exact cycles, options, and controls it includes.

Kenmore Elite models are positioned above standard Kenmore appliances in features and finish. In washers, that commonly includes:

• More specialty cycles and option combinations
• Higher spin performance for better water extraction
• Improved vibration control and noise reduction
• More advanced electronic controls and diagnostics
• Convenience features such as additional dispensers or cycle customization (varies by model)

The most accurate way to judge “high end” is to compare real capabilities, not just the badge. For 41748102700, check the cycle list, temperature selections, spin choices, and available options in the manual.

“High end” usually translates to better fabric care flexibility, stronger water removal (shorter dry times), and a quieter, smoother wash experience. Comparing cycles and options helps you decide if an Elite model offers benefits you will actually use.

Use model-family troubleshooting to interpret symptoms and codes before replacing parts:

• Check the displayed code and when it appears
• Note whether the issue happens during fill, wash, drain, or spin
• Match the code to the recommended checks and resets

A good starting point is Kenmore 417 front load washer error codes.

Last updated: February 2026