KitchenAid KESS907SSS06 30" electric slide-in oven Parts

On your KitchenAid KESS907SSS06 electric range, you can clear many error codes by pressing Cancel/Off once to stop the cycle and reset the control. If the code returns, do a full power reset at the breaker for 1 minute, then restore power and retry the function.

Quick reset steps (safe order)

• Press Cancel/Off and wait 30 seconds.
• If the display stays in an error state, turn OFF the range circuit breaker.
• Leave power OFF for 60 seconds.
• Turn the breaker ON and set the clock if prompted.
• Start Bake and confirm the oven heats normally.
• If the code returns immediately, stop using the oven and troubleshoot the likely cause below.

What the error code usually points to

Most KitchenAid range error codes fall into a few common groups. Use this as a fast guide before replacing parts.

What you see	What it often means	What to check next
Code returns right after reset	Control is still detecting a fault	Wiring connections, sensor, door lock
Oven won’t heat or heats poorly	Heating circuit problem	Bake element, wiring, power supply
Temperature seems inaccurate	Sensing problem	Oven sensor, sensor harness
Self-clean issues or door won’t unlock	Lock system problem	Door lock assembly, switch alignment

Model-specific checks we recommend for KESS907SSS06

1. Confirm proper power supply: This range must be connected to the correct voltage and wiring method for safe operation. Use the electrical connection guidance in the installation guide.
2. Inspect the terminal block for overheating: A loose connection can cause power faults and repeated codes. If you see heat damage, check the range terminal block WPW10245259.
3. Check oven temperature sensing: If the oven overheats, underheats, or throws temperature-related codes, test the sensor circuit and consider the wall oven temperature sensor WPW10131825.

Why it matters

Clearing the code without fixing the underlying issue can lead to repeated shutdowns, poor baking performance, or unsafe electrical conditions. A quick reset is a good first step, but a returning code is a diagnostic clue.

Last updated: February 2026

A KitchenAid electric oven like model KESS907SSS06 typically lasts 15 years. With normal home use and basic care (keeping vents clear, avoiding frequent high-heat self-clean cycles, and fixing heating issues early), many ranges reach the 10 to 20 year range.

Typical lifespan ranges

Most 30-inch electric slide-in ranges fall into these expectations:

• Typical: 15 years
• Common range: 10 to 20 years
• Shorter lifespan drivers: heavy daily use, frequent self-clean, power surges, overheating from blocked airflow
• Longer lifespan drivers: steady electrical supply, prompt part replacement, gentle cleaning habits

What you do	What it affects	Result over time
Run self-clean often	Control electronics, door lock, wiring	More heat stress, earlier failures
Keep the oven clean manually	Bake/broil performance, odors	More consistent heating
Fix uneven heating quickly	Elements and temperature control	Prevents secondary damage
Ensure proper installation clearances	Cooling airflow, cabinet heat	Reduces overheating risk

Parts that most often determine “end of life”

On the KESS907SSS06, the range usually becomes frustrating when key heating or control parts start failing repeatedly. These are common wear items we see:

• Heating element issues (no heat, slow preheat, uneven baking): range bake element WPW10207398
• Temperature regulation problems (overheats, underheats, long preheat): wall oven temperature sensor WPW10131825
• Self-clean lock problems (door won’t lock or unlock): range oven door lock assembly WPW10195934
• Cooktop heat control problems (burner stuck high/low): range surface element control switch WP9763761
• Power connection damage or intermittent power: range terminal block WPW10245259

Why installation and airflow matter

This KitchenAid range is designed to meet cabinet temperature limits when installed with the required clearances and safety hardware. Proper setup helps the oven cool correctly, which protects wiring, controls, and sensors over the long run. For model-specific requirements, use the KESS907SSS06 installation guide.

When replacement makes more sense than repair

Replacement is the better call when you see a pattern like this:

• Multiple major parts fail within 12 to 24 months
• The oven won’t maintain temperature even after an element or sensor replacement
• The control panel becomes unreliable (random beeps, unresponsive keys)
• You smell repeated overheating at the power connection area

Last updated: February 2026

On the KitchenAid range model KESS907SSS06, the model and serial number plate is located inside the oven door on the right-hand side oven door trim. Open the oven door fully and look along the right-side trim for the rating plate.

Where to look (fast checklist)

• Open the oven door and use a flashlight
• Check the right-hand oven door trim (not the left)
• Look for a model/serial number plate or rating plate sticker/metal tag
• Wipe grease or residue off the trim so the print is readable
• Write down the full model number and serial number exactly as shown

What the plate looks like and why it matters

The plate is the appliance’s identification tag. We use it to match the correct KitchenAid parts and to confirm electrical requirements listed for your range.

Common label wording

You might see	What it means
Model	The exact model number (KESS907SSS06) used to match parts diagrams
Serial	Production code used for manufacturing date and version
Rating plate	Electrical information (voltage/amps) used for safe installation

Tips if the label is hard to read

• Clean the area with a damp cloth and mild soap; dry completely
• Take a close-up photo and zoom in
• If the label is damaged, use the installation paperwork to confirm the model number and then match parts by diagram

Why it matters

Using the exact model number prevents ordering the wrong bake element, oven sensor, or control parts for your 30-inch electric slide-in range.

For a diagram showing the plate location, see the installation guide.

Last updated: March 2026