Installation guide
Owner’s manual
Error Codes
Can you still get parts for a Kenmore dishwasher?
Yes. We still support Kenmore dishwasher parts, and for Kenmore model 58712332F01B you can buy common replacement parts like a door latch, water inlet valve, drain pump, and detergent dispenser; match parts by the full model number shown in your 58712332F01B owner's manual.
Use the model number 58712332F01B (not just “Kenmore 587”) and confirm the part’s name and identifiers before ordering.
- Match the full model number from the rating label to the parts list
- Compare the part name to the symptom (leak, no fill, no drain, won’t start)
- Check for included hardware (brackets, screws, seals) when applicable
- Replace any disturbed seals or O-rings during reassembly
- Follow shutoff and wiring steps in the 58712332F01B installation guide when removing the dishwasher
These are examples of parts available for 58712332F01B that often solve common problems:
| Symptom | Common fix | Example part for this model |
|---|---|---|
| Door won’t latch or unit won’t start | Replace door latch | Dishwasher door latch 5304535183 |
| Dishwasher won’t fill | Replace inlet valve | Dishwasher water inlet valve (model-matched) |
| Dishwasher won’t drain | Replace drain pump | Dishwasher drain pump (model-matched) |
| Detergent door won’t open | Replace dispenser | Electrolux dishwasher detergent dispenser assembly (model-matched) |
Kenmore dishwashers are built across multiple manufacturing platforms, so parts are model-specific. Using 58712332F01B ensures you get the correct fit, wiring connections, and mounting style for your dishwasher.
Last updated: February 2026
How do I tell which Kenmore dishwasher I have?
To tell which Kenmore dishwasher you have, we look up the model number and serial number on the rating label (serial plate) located inside the dishwasher, typically just inside the door. For your unit, the model number format matches the 587.1233* series shown in the 58712332F01B owner's manual.
On Kenmore dishwashers like model 58712332F01B, the label is inside the tub area and is easiest to see with the door open.
- Open the dishwasher door fully.
- Look along the inner frame of the tub opening (often on the left side or near the door opening).
- Find the sticker or metal plate labeled Model and Serial.
- Write the numbers down exactly as shown (letters and numbers matter).
- Use that full model number when ordering parts such as a door latch, water inlet valve, or drain pump.
Your model number is the key to getting the right parts list, diagrams, and instructions.
| What you see on the label | What it’s used for |
|---|---|
| Model number (example: 58712332F01B) | Matching the correct parts and diagrams |
| Serial number | Identifying production details for service and support |
| Series pattern (example: 587.1233*) | Confirming the family of Kenmore dishwasher designs |
Kenmore dishwashers can look similar across different series, but parts like the dishwasher door latch, detergent dispenser assembly, and wire harness can vary by model. Using the exact model number helps prevent ordering a part that does not fit.
- Wipe the label gently with a damp cloth to remove film.
- Use a flashlight and take a close-up photo to zoom in.
- If the door will not close or latch, inspect the dishwasher door latch 5304535183 because a misaligned or failing latch can make identification and operation harder.
Last updated: February 2026
What is the code F2E2 on a Kenmore Elite dishwasher?
On a Kenmore dishwasher, error code F2E2 means the user interface (keypad) is not communicating correctly with the main control, so button presses may not respond or the cycle may stop. For model 58712332F01B, we use the troubleshooting and reset steps in the 58712332F01B owner’s manual.
- Press Start/Cancel to turn the unit off, then wait about 1 minute and try a normal cycle again.
- Make sure no keys are stuck; wipe the console with a soft, slightly damp cloth and dry it.
- Turn off power at the breaker for 2 minutes, then restore power and retry.
- If the dishwasher was recently installed or moved, confirm the unit is fully secured and not flexing when you press keys (movement can stress wiring).
- If the code returns immediately, plan on inspecting the console and control connections.
| Likely cause | What you’ll notice | Typical fix |
|---|---|---|
| Loose or oxidized connector between UI and control | Code comes and goes, random beeps | Reseat connectors, check for corrosion |
| Damaged wire harness | Works until door moves, then fails | Repair/replace harness |
| Failed user interface (keypad/console) | Certain keys never work | Replace console/UI |
| Failed main control board | Multiple odd behaviors | Replace control board |
If the dishwasher also will not start because the door is not registering as closed, check the latch first. A weak latch can cause intermittent operation that looks like an electronic problem.
- Consider inspecting the dishwasher door latch 5304535183 for wear, binding, or a loose mounting.
F2E2 is a control communication fault; continuing to run cycles can lead to mid-cycle stops, poor cleaning, and repeated resets. Fixing the connection or the failed control component restores reliable keypad response and normal cycle operation.
Last updated: February 2026
