Samsung RF31FMEDBWW/AA-00 refrigerator Parts

To remove the bottom glass shelf in your Samsung RF31FMEDBWW, lift the front edge, slide the shelf forward, then angle the glass sideways to clear the cabinet stops. The key is rotating the shelf to line up with the notch so it can pass through.

Steps to remove the bottom shelf safely

• Remove food and bins/drawers that block the shelf from sliding forward.
• Lift the front of the shelf slightly to unseat it from the rear supports.
• Slide the shelf forward until it stops.
• Rotate the shelf glass sideways (vertical) to align with the cabinet notch/clearance.
• Pull the shelf out slowly, keeping the glass supported with both hands.
• Set the shelf on a flat surface to avoid twisting the frame.

Common hang-ups (and what they mean)

What you feel	Most likely cause	What to do
Shelf stops after sliding forward	It is hitting the cabinet stop	Lift slightly and rotate the glass sideways
Shelf won’t lift at the front	It is still loaded or wedged	Remove items and check for a bin lip catching
Glass feels stuck in the frame	Normal tight fit or minor binding	Support both sides and avoid flexing the glass

Why it matters

Removing the shelf the right way prevents chipped glass edges, cracked shelf frames, and damage to the liner rails. It also makes it easier to clean spills and access the crisper area without forcing parts.

Model-specific reference

For shelf handling and interior component removal guidance for Samsung RF31FMEDBWW, follow the diagrams and cautions in the RF31FMEDBWW owner's manual.

Last updated: January 2026

For Samsung refrigerators like model RF31FMEDBWW, the most common customer-reported problems are ice maker issues (no ice, small cubes, freezing up) and cooling complaints (warm fresh food section, frost buildup, noisy fan). These symptoms usually trace back to airflow restrictions, sensor problems, or water supply issues.

Most common issues we see (and what they point to)

• Ice maker not making ice or freezing up: often caused by low water flow, a restricted filter, or ice buildup around the ice room
• Water dispenser slow or not dispensing: commonly a clogged filter or a weak/closed supply valve
• Fresh food section warm but freezer cold: typically an airflow problem (blocked vents, frost on evaporator cover)
• Loud humming, buzzing, or rattling: frequently an evaporator fan issue or ice contacting the fan
• Temperature swings: can be related to a failing temperature sensor or control response

Quick checks before replacing parts

1. Confirm the temperature settings are at normal targets (about 37°F fresh food, 0°F freezer).
2. Make sure air vents are not blocked by food packages.
3. If water flow is weak, replace the filter and flush several gallons.
4. Inspect for frost or ice buildup on the back wall inside the refrigerator section.
5. Review the troubleshooting and diagnostic steps in the RF31FMEDBWW owner's manual.

Parts that commonly relate to these symptoms

Symptom	Common cause	Example part for RF31FMEDBWW
Slow water, no ice	Restricted filter	Refrigerator water filter DA29-00020B
Warm fridge, frost buildup	Sensor or airflow/defrost issue	Refrigerator temperature sensor (model-specific)
Noisy fan, warm temps	Fan/air movement problem	Refrigerator evaporator fan (model-specific)

Why it matters

Ice maker and cooling problems can quickly lead to food spoilage, leaks, and extra strain on the sealed system. Catching airflow restrictions and water flow problems early is the fastest way to restore normal performance.

Last updated: January 2026

Your Samsung refrigerator’s model number is printed on the rating label; on RF31FMEDBWW units it’s typically inside the fresh food compartment on a side wall near the crisper drawers, or on the ceiling area near the top hinge. Use the full model number when ordering parts.

Where to look on the refrigerator

Check these common label locations first:

• Inside the refrigerator section on the left or right side wall
• Near the crisper drawers (above or beside the drawers)
• On the ceiling of the fresh food compartment
• Along the door frame (hinge side) when the door is open
• On the back exterior panel (less common, but possible)

What to write down (so parts match)

Samsung model labels often include more than one identifier. Record:

• Model number (example: RF31FMEDBWW)
• Version code (often shown as something like “/AA”)
• Serial number (helpful for service history and age)

Quick ID guide

Label item	What it’s used for	Why it matters
Model number	Finding diagrams and parts	Ensures correct fit and compatibility
Version code	Matching exact production run	Prevents ordering a similar but different part
Serial number	Dating and service reference	Helps narrow down configuration

Why it matters

Small differences in a Samsung bottom-mount refrigerator (controls, ice room fan, water filter housing, door parts) can change which replacement part fits. Using the complete model and version code helps us match the correct components the first time.

If the label is hard to read

• Wipe the label gently with a damp cloth and dry it
• Take a clear photo and zoom in
• Compare the characters carefully (0 vs O, 1 vs I)

For label examples and additional location notes, use the RF31FMEDBWW owner's manual.

Last updated: March 2026