Kenmore Elite 79047153401 gas range Parts

For your Kenmore Elite gas range model 79047153401, the reliable “reset” for the oven control is a power reset: turn the range power off at the breaker (or unplug it) for about 5 minutes, then restore power. If the control is beeping with an F-code, press STOP/CLEAR to stop the beeping and clear the display.

Quick reset steps (safe, first)

• Press STOP/CLEAR once to cancel any active cooking mode.
• Turn OFF the circuit breaker to the range (or unplug the power cord).
• Wait 5 minutes.
• Restore power.
• Set the clock, then test BAKE and BROIL.

If the control is locked (looks “stuck” but is not broken)

This model has an Oven Lockout feature that can make the oven seem unresponsive.

• Press and hold STOP/CLEAR for 3 seconds to toggle Oven Lockout.
• Watch for the lock indicator and “DOOR LOCKED” message to change.
• Wait for the door to fully unlock before trying to start a cycle.

Reference the exact key sequence and indicators in the owner's manual.

When an error code keeps coming back (F1, F2, F3, F9)

If the oven control beeps and shows F1, F2, F3, or F9, the control is detecting a fault.

What you see	What to do next	What it usually means
Continuous beeping + F-code	Press STOP/CLEAR, power reset, then reprogram	A fault was detected during operation
F-code returns after reset	Record the code and symptoms	A component or the electronic control may need service

Why it matters

A power reset clears temporary control glitches after a surge or keypad confusion. If the same fault code returns, the range is protecting itself by stopping operation, which helps prevent unreliable heating or unsafe cycling.

Last updated: February 2026

PF on the Kenmore Elite range model 79047153401 means power failure; it appears when the range is first plugged in or when electrical power to the range is interrupted. To clear it, press STOP/CLEAR; after about 10 seconds, PF should disappear.

What causes PF on this range?

PF is not a “bad part” code by itself. It is the control telling you it lost power long enough to reset the clock.

Common causes include:

• A brief power outage or flicker in your home
• The range being unplugged, even momentarily
• A tripped breaker or loose outlet connection
• A loose power cord connection at the range terminal block
• Service work where power was shut off and restored

How to clear PF and reset the clock

Use these steps for model 79047153401:

• Press STOP/CLEAR once to acknowledge the PF message
• Wait about 10 seconds for the beep and for PF to clear
• Press CLOCK
• Use the number pads to set the correct time
• Press CLOCK again to start the clock

For the exact key sequence and display behavior, follow the owner's manual.

If PF keeps coming back (what to check next)

If PF returns repeatedly without a known outage, focus on the power supply path.

What to check	What you are looking for	What it affects
Wall outlet and plug	Plug fully seated, outlet not loose	Prevents intermittent power loss
Breaker	Breaker not tripping, no overheating	Stops repeated resets
Power cord connections	Tight, not burned or discolored	Prevents arcing and dropouts
Terminal block	Signs of heat damage, loose lugs	Common point of failure on ranges

If you find heat damage or loose connections at the terminal block area, replacing the terminal block 5304409888 is a common repair.

Why it matters

When the control loses power, cooking functions can stop and the clock and timed features reset. Clearing PF is normal after an outage; repeated PF points to a power connection issue that should be corrected to prevent further interruptions.

Last updated: February 2026

On the Kenmore Elite range model 79047153401, an NCAL message typically points to an oven control calibration or control fault. Start with a power reset; if the code returns, the next step is diagnosing the electronic oven control and related wiring using the procedures in the owner's manual.

What to do first (safe, quick checks)

• Press STOP/CLEAR to silence beeping and clear the display.
• Unplug the range (or switch the breaker off) for 1 minute, then restore power.
• If the code returns immediately, avoid using Bake/Broil/Clean until you troubleshoot.
• Check for a recent power outage or surge; control faults often show up after power events.
• If the display is beeping with other fault codes (such as F1, F2, F3, or F9), record the exact code and symptoms.

What NCAL usually means on this type of range

NCAL is commonly treated as a control calibration-related error. In practical terms, that means the electronic oven control (clock/control board) is not operating within its expected parameters, or it is seeing an abnormal signal from a monitored circuit.

Common causes

Likely cause	What you may notice	Typical fix
Control glitch after power interruption	Code appears after outage	Power reset, then retest
Loose or damaged wiring connection	Intermittent code, random beeping	Inspect and repair wiring/connectors
Failing electronic oven control	Code returns quickly after reset	Replace the control board

How to narrow it down

• If the oven beeps continuously: press STOP/CLEAR; if it returns, treat it as an active fault.
• If the oven temperature seems wrong: test the oven temperature sensor circuit; a bad sensor can contribute to control errors. For this model, the sensor is frigidaire range oven temperature sensor 316217002.
• If you see signs of heat damage behind the control panel: inspect wiring and terminals; overheated connections can cause repeated control faults.

Why it matters

When the control loses calibration or detects an internal fault, it can stop heating mid-cycle, misread temperature, or lock out functions. Addressing the code early helps prevent inconsistent baking and repeated shutdowns.

Last updated: February 2026