Amana BZ22RL-P1161601WL bottom-mount refrigerator Parts

On the Amana BZ22RL-P1161601WL bottom-mount refrigerator, the bottom of the freezer door usually won’t seal because the door is slightly out of alignment, the gasket is dirty or deformed, or the door is being held open by ice buildup or an overfilled bin.

• Make sure nothing inside the freezer is pushing the door outward (bags, pizza boxes, baskets).
• Look for frost or ice along the bottom rail that prevents the gasket from contacting the cabinet.
• Clean the gasket and the cabinet sealing surface with warm water and mild dish soap; dry fully.
• Do the “paper test”: close the door on a strip of paper at the bottom; it should drag when you pull.
• Confirm the refrigerator is level and slightly tilted back so doors self-close.

A gasket can look “fine” but still leak at the bottom if it is stiff, wavy, or torn.

If the gasket is torn or won’t hold shape after cleaning and warming, replacement is the lasting fix. For this model, the freezer door gasket is gasket,fz dr WP12550116Q.

• Check that the freezer drawer is fully seated on both slides.
• Verify the door closes evenly without rubbing.
• If the door “springs back” open, re-level the refrigerator so the front is slightly higher than the back.

A poor freezer door seal lets warm, moist air in; that causes frost buildup, longer run times, temperature swings, and can lead to ice maker and defrost complaints.

For more seal troubleshooting steps, use how to fix a fridge door seal.

Last updated: January 2026

On the Amana BZ22RL-P1161601WL bottom-mount refrigerator, you typically adjust the bottom freezer drawer by turning the drawer-front adjustment screws a small amount, then closing the drawer to recheck the gap and alignment. A common starting point is two full turns, then fine-tune.

• Unload heavy items from the freezer drawer to reduce sag while you set alignment.
• Make sure the refrigerator is level front-to-back and side-to-side (leveling issues mimic a “crooked” drawer).
• Check for ice buildup, packaging, or a bin that is preventing full closure.
• Confirm both drawer slides move smoothly and evenly.

1. Open the freezer drawer and locate the left and right adjustment screws (usually behind caps or on the inside of the drawer front brackets).
2. Turn each side in small, equal increments.
3. Close the drawer and check the gap along the top edge and the seal contact.
4. Repeat until the drawer front is even and the gasket seals all the way around.

• Inspect the gasket for twists, tears, or areas not contacting the cabinet; a warm, damp cloth can help relax minor waves.
• Look for a bent bracket or loose fastener; tighten hardware if you find play.
• If the drawer is aligned but warm air still leaks in, the gasket may need replacement; see gasket,fz dr WP12550116Q.
• If the refrigerator compartment door is the issue (not the freezer), see refrigerator door gasket WP12550115Q.

A properly aligned bottom freezer door helps the gasket seal tightly, which prevents frost buildup, reduces compressor run time, and keeps temperatures stable for better food preservation.

Last updated: January 2026

If your Amana BZ22RL-P1161601WL bottom-mount refrigerator freezer isn’t freezing, the most common causes are poor airflow from frost buildup, an evaporator fan problem, or a temperature control issue. Start with simple checks (settings, door seal, vents) before testing parts.

• Confirm the freezer temperature is set cold enough; most freezers should be near 0°F.
• Make sure food packages are not blocking interior air vents.
• Check that the freezer door closes fully and the gasket seals all the way around.
• Look for heavy frost on the back freezer panel (often points to a defrost problem).
• Verify the condenser area is not packed with dust and the unit has airflow around it.

When the compressor is running, you should typically hear or feel airflow in the freezer.

If the quick checks point to a component issue, these model-matched parts are common suspects:

• Evaporator motor WP10513803: circulates cold air through the freezer and into the fresh food section.
• Refrigerator defrost heater WP10428409: melts frost off the evaporator during defrost cycles.
• Refrigerator thermostat WP10442411: helps regulate cooling based on temperature.
• Refrigerator temperature control W10752646: sets and manages the cooling level.
• Refrigerator door gasket WP12550115Q and gasket,fz dr WP12550116Q: prevent warm air leaks that cause poor freezing.

A freezer that is not freezing is usually an airflow or frost issue first; fixing the root cause prevents repeat icing, food spoilage, and extra strain on the compressor.

Last updated: January 2026

If your Amana bottom-mount refrigerator model BZ22RL-P1161601WL is leaking water from the bottom, the most common causes are a clogged defrost drain (water overflows and runs to the floor), a cracked or shifted drain pan, or a door gasket leak that creates excess condensation.

• Unplug the refrigerator before inspecting near wiring or the evaporator area.
• Look for a sheet of ice or standing water under the crisper drawers (classic defrost drain clog sign).
• Check the drain pan underneath for cracks, warping, or being out of position.
• Inspect the door seals for gaps, tears, or areas that do not grip paper when the door is closed.
• Confirm the refrigerator is level (front slightly higher helps doors seal and drain correctly).

If you find a sealing problem, these model-matched gaskets are common leak contributors:

• Refrigerator door gasket WP12550115Q
• Gasket,fz dr WP12550116Q

Bottom leaks often start as a small drain restriction or air leak. Fixing it early helps prevent ice buildup in the drain path, recurring puddles, and temperature swings that can stress the compressor and evaporator fan system.

For step-by-step cleaning and prevention tips, use our guide: how to get rid of refrigerator puddles.

Last updated: January 2026