Owner’s manual
Error Codes
What size is a Kenmore Model 11070812990 dryer?
Kenmore gas dryer model 11070812990 is a full-size, standard-width dryer. Most Kenmore 110-series dryers measure about 27 inches wide, 27 to 29 inches deep, and 43 to 44 inches high. For the exact cabinet dimensions for your unit, use the specs listed in the 11070812990 owner's manual.
These are the measurements we see most often for this style of Kenmore (Whirlpool-built) gas dryer:
- Width: ~27 inches
- Height: ~43 to 44 inches
- Depth (cabinet): ~27 to 29 inches
- Depth (door open): typically increases several inches beyond cabinet depth
- Capacity class: “Super Capacity Plus” (from the manual)
If you are fitting the dryer into a laundry alcove or replacing an older unit, measure your actual dryer and compare to the space.
- Measure width at the widest point of the cabinet (not the knobs).
- Measure height from floor to the top of the cabinet.
- Measure depth from the back panel to the front of the closed door.
- Add space for the gas line connection and exhaust vent behind the dryer.
- Confirm the model/serial plate inside the door matches 11070812990.
| What you are planning for | What to allow | Why |
|---|---|---|
| Side clearance | 0 to 1 inch each side | Prevents rubbing and vibration noise |
| Rear clearance | 4 to 6 inches typical | Room for venting and gas hookup |
| Top clearance | 0 to 1 inch | Helps with airflow and easier installation |
Dryer “size” is not just the cabinet dimensions. Vent routing, the gas hookup, and door swing can change whether a dryer fits and operates safely. Using the exact specs from the manual helps avoid crushed vents, poor airflow, and longer dry times.
If you are also planning a repair while moving the dryer, common fit-related parts for this model include the dryer drum belt 341241 and the dryer door seal W10906683. You can order replacement parts from the parts list for model 11070812990, or search by model number on Sears PartsDirect.
Last updated: February 2026
How do I find out what size dryer belt I need?
For Kenmore gas dryer model 11070812990, the most reliable way to get the correct belt size is to match the belt to the model’s specified replacement part. If you’re measuring an old belt, measure its width and its total loop length (outside circumference) while keeping it flat and taut; stretched belts can read long.
- Use the model-based parts list to avoid guesswork.
- Order the model-matched belt: dryer drum belt 341241.
- Confirm installation routing and access steps in the owner's manual.
- If the old belt is broken or missing, skip measuring and use the model match.
- Unplug the dryer and shut off the gas supply before opening panels.
- Remove the belt (or use a piece of string to trace the belt path if it’s still installed).
- Measure:
- Width: measure across the belt.
- Loop length: measure the full outside circumference (wrap string around the belt loop, then measure the string).
- Keep the belt flat and lightly tensioned; don’t stretch it.
| What you measure | How to measure it | Common mistake |
|---|---|---|
| Belt width | Straight across the belt | Measuring a frayed edge |
| Belt loop length | Outside circumference of the loop | Pulling tight and overstretching |
| Belt condition | Look for glazing/cracks | Reusing a belt that slips |
A belt that’s too long can slip and cause slow tumbling or squealing; a belt that’s too short can overload the motor and idler system. Using the model-correct belt helps the drum turn at the right speed and keeps drying performance consistent.
We recommend ordering by model number first, then selecting the exact part from the list for 11070812990. If you’re shopping for additional maintenance items at the same time, you can also search by model on Sears PartsDirect.
Last updated: February 2026
How do I tell what model my Kenmore dryer is?
Your Kenmore dryer’s model number is printed on the model and serial number plate; on Kenmore model 11070812990, that plate is typically located around the door opening area. Once you have the full model number, we can match the correct parts list and the right owner’s manual for your exact dryer.
Check these common locations on Kenmore gas dryers like 11070812990:
- Along the door opening on the cabinet (often on the inner frame)
- On the inside of the dryer door
- On the front panel just inside the door opening
- On the back panel (less common, but possible)
- Near the lint screen housing area (varies by design)
If you see multiple numbers, use the one labeled Model (not the serial number).
Kenmore model numbers are usually a long string of digits. For this dryer, the model number is 11070812990.
- Ensures you get parts that fit your exact drum, motor, and burner setup
- Helps you pull the correct wiring diagram and troubleshooting steps
- Prevents ordering look-alike parts that do not match your version
Use this table to avoid mix-ups:
| Label on tag | What it’s used for | Example for this dryer |
|---|---|---|
| Model | Parts lookup, manuals, diagrams | 11070812990 |
| Serial | Manufacturing code, production info | Varies |
Once you confirm the model number, we recommend:
- Compare it character-for-character (no spaces) to 11070812990
- Use the 11070812990 owner’s manual to confirm features and control layout
- If you’re ordering common wear items, match by model first, then choose the part
- Dryer drum belt 341241 (belt slips or breaks; drum will not tumble)
- Dryer door switch WP3406107 (dryer will not start if the switch fails)
For additional parts searches by model number across appliances, use Sears PartsDirect.
Last updated: February 2026
