Kenmore 11026852503 washer Parts

The exact wash capacity (in cubic feet) for Kenmore washer model 11026852503 is listed in the product specifications section of the 11026852503 owner's manual. This model is a full-size top-load washer; most washers in this class typically fall in the 3.2 to 3.6 cu. ft. range.

How to confirm the capacity for model 11026852503

Use the manual specs so you get the correct number for your exact version.

• Open the 11026852503 owner's manual
• Look for “Specifications”, “Product dimensions”, or “Capacity”
• If the manual lists basket size by diameter/depth instead of cu. ft., use the cu. ft. value when available (it is the most comparable spec)
• Match the model number exactly: 11026852503
• If you are comparing to another washer, compare cu. ft. (not “large/extra-large” marketing terms)

Typical capacity ranges (for context)

If you are planning loads or comparing machines, these ranges are a reliable guide for full-size top-load washers like this Kenmore.

Washer type	Typical capacity range	Best for
Standard top-load (agitator)	3.0 to 3.6 cu. ft.	Everyday mixed loads
High-efficiency top-load	4.0 to 5.5 cu. ft.	Larger loads, bulky items
Compact top-load	1.5 to 2.8 cu. ft.	Small spaces, lighter use

Why it matters

Capacity affects how well clothes move during agitation and rinse. Overloading reduces cleaning performance and can increase wear on drive components such as the washer motor coupling 285753A and the spin system.

Last updated: January 2026

To hard reset a Kenmore washer model 11026852503, we typically power-cycle it: turn the washer off, unplug it for about 1 minute, then plug it back in and restart a cycle. This clears many temporary control glitches and stuck cycle states.

Hard reset steps (power reset)

• Push in the cycle control knob to stop the washer.
• Unplug the washer from the wall outlet (or switch the breaker off).
• Wait 60 seconds.
• Restore power.
• Close the lid and pull the cycle control knob out to start.

For model-specific start/stop behavior, follow the steps in the 11026852503 owner’s manual.

If the washer still will not start after a reset

A “reset” will not fix a failed safety switch or a no-drain condition. Check these common causes:

• Lid not fully closed; the washer will not run if the lid switch is not made.
• No drain or slow drain; water left in the tub can stop the cycle from advancing.
• Stuck timer/cycle control knob; the knob must be pulled out to run.
• Power issue; outlet, breaker, or loose cord connection.

Quick part checks that often solve “won’t run” symptoms

Symptom after reset	Most common check	Related part for this model
Nothing happens when you pull the knob	Lid switch not engaging	Washer lid switch assembly WP8318084
Hums but will not drain/spin	Pump jammed or failed	Washer drain pump WP3363394
Agitates but will not spin (or vice versa)	Drive coupling worn	Washer motor coupling 285753A

Why it matters

Resetting clears minor electronic or timer interruptions, but it also helps us separate a one-time glitch from a repeatable failure (like a lid switch, drain pump, or drive coupling problem). That saves time and prevents unnecessary part replacement.

Helpful installation-related tip (vibration after moving the washer)

If the washer was recently moved, leveling issues can look like a “control problem.” Use the 11026852503 installation guide to confirm the self-adjusting rear feet are set and the unit is level.

Last updated: January 2026

Yes, most Kenmore Elite washers use a drain pump filter or a self-cleaning pump system, depending on the design. For Kenmore model 11026852503, the most common “filter” you service is the drain pump inlet area where debris can collect; cleaning it helps prevent no-drain and slow-drain problems. See the 11026852503 owner's manual for the exact cleaning and access method.

Where the “filter” is on this washer

On many Kenmore top-load designs like 11026852503, lint and small items are typically caught at the drain pump rather than a removable lint screen.

Common places debris collects:

• Drain pump inlet (coins, socks, hair pins)
• Inner drain hose between tub and pump
• Tub outlet area (lint buildup)
• Standpipe or household drain (can mimic a clogged pump)

If you suspect a pump restriction, the replacement part for this model is the washer drain pump WP3363394.

How to check and clean it (safe, practical steps)

1. Unplug the washer.
2. Turn off both water faucets.
3. Bail out water if the tub is full.
4. Access the pump area (method varies by cabinet style).
5. Remove the pump hoses and clear debris; check for broken plastic pieces.
6. Reinstall hoses securely and run a rinse and spin to confirm draining.

Quick symptom-to-cause guide

Symptom	Most likely cause	What to check first
Won’t drain	Pump jam or failed pump	Pump inlet and impeller
Drains slowly	Partial clog	Hose from tub to pump
Stops mid-cycle	Lid switch issue	Lid switch operation
Hums but won’t drain	Jammed impeller	Debris in pump

Why it matters

A clogged pump area can leave water in the tub, cause odors, and strain the drive system during spin. Keeping the drain path clear is one of the simplest ways to extend washer life and avoid repeat no-drain calls.

Last updated: January 2026