Kenmore 11026852504 washer Parts

A hard reset on our Kenmore washer model 11026852504 is simple: unplug the washer (or switch off the breaker) for 2 minutes, then restore power. This clears many temporary control glitches; if the washer still acts up, use the reset and restart steps in the 11026852504 owner's manual.

Hard reset steps (power reset)

• Turn the cycle knob to Off.
• Unplug the washer (or turn the breaker Off).
• Wait 2 minutes.
• Restore power.
• Set a normal cycle and start the washer.

If it still will not run: quick checks that often look like a “needs reset” problem

Many “won’t start” complaints are caused by a stop condition, not a bad control.

• Make sure the lid is fully closed; this model uses a lid safety switch.
• If the washer stopped mid-cycle, push in the cycle control knob to stop, then pull out to restart (lid closed).
• Confirm the washer is level; excessive vibration can interrupt operation.
• Verify the drain can handle flow; a slow/clogged drain can cause backing up and odd behavior.
• Check for a loose or damaged lid switch; consider inspecting the washer lid switch assembly WP8318084 if the washer will not agitate or spin with the lid closed.

Reset vs. restart: what’s the difference?

Action	What it does	When to use it
Hard reset (unplug 2 minutes)	Clears temporary control state	Random stopping, odd timer behavior
Restart cycle (push in/pull out knob)	Resumes operation safely	Paused cycle, lid opened
Leveling adjustment	Prevents vibration-related issues	Walking, banging, out-of-balance

Why it matters

A proper hard reset is fast and safe, but repeated “reset fixes” usually point to an underlying issue such as a lid switch problem, draining restriction, or an out-of-level installation. Following the correct restart procedure also prevents unnecessary part replacement.

Last updated: January 2026

Most Kenmore washers, including model 11026852504, typically last 10 to 15 years with normal household use and basic maintenance. Heavy loads, frequent use, and poor installation conditions can shorten lifespan; timely repairs often extend it.

What affects washer lifespan the most

• Load size and frequency: frequent oversized loads strain the drive system and suspension.
• Water quality and detergent use: too much detergent can leave residue and increase wear.
• Drain and spin health: slow draining or repeated off-balance spins accelerate component wear.
• Installation conditions: a level, sturdy floor and proper water pressure help prevent vibration and premature failures.
• Temperature exposure: operating or storing at or below 32°F (0°C) can leave trapped water that damages components.

Quick maintenance habits that add years

Use these habits alongside the care guidance in the 11026852504 washer use & care guide.

• Keep loads balanced; mix large and small items.
• Use the correct detergent amount; avoid over-sudsing.
• Periodically check fill hoses and the drain path for kinks or restrictions.
• If the washer will be exposed to freezing temperatures, winterize it as outlined in the manual.
• Address new noises, burning smells, or weak agitation early to avoid secondary damage.

Common “end-of-life” symptoms and likely repair areas

Symptom	What it often points to	Example part for this model
Won’t spin or agitates poorly	Drive train wear	Washer motor coupling 285753A
Won’t drain or drains slowly	Pump blockage or failure	Washer drain pump WP3363394
Won’t start or stops when lid opens	Lid switch issue	Washer lid switch assembly WP8318084

Why it matters

A washer that is installed correctly and maintained tends to reach the full 10 to 15 year lifespan, while chronic vibration, draining problems, or freezing exposure can turn small issues into major repairs. For model 11026852504, following the setup requirements in the 11026852504 installation guide helps prevent avoidable wear from day one.

Last updated: January 2026

On Kenmore washer model 11026852504, an FE error code typically points to an overfill condition; the washer may keep filling or the drain pump may run to prevent flooding. The most common fix is correcting a water-inlet problem (stuck inlet valve) and then verifying the washer is installed and operating correctly per the 11026852504 owner's manual.

What to check first (fast, safe steps)

• Unplug the washer and turn both water faucets off.
• If the tub is overfilled, set the timer to drain/spin after restoring power briefly, then unplug again.
• Inspect the fill hoses for kinks and confirm hot and cold hoses are connected correctly.
• Make sure the washer is not siphoning (drain hose pushed too far down the standpipe).
• If the washer keeps filling with power off, the inlet valve is mechanically stuck open and needs replacement.

Likely causes and the best fix

Symptom	Most likely cause	What we recommend
Water continues to enter with washer unplugged	Inlet water valve stuck open	Replace the inlet valve assembly
FE shows and pump runs, water level seems wrong	Pressure system issue (hose/air dome)	Check for a loose, pinched, or clogged pressure hose
FE happens during install or after moving	Drain hose/standpipe setup causing siphon	Reposition drain hose and secure it properly

Parts that commonly relate to FE-type symptoms

If the washer will not complete cycles after correcting the fill issue, these parts are often involved in related no-spin or no-drain complaints:

• Washer drain pump WP3363394 (helps clear water when the washer is trying to protect against overfill)
• Washer lid switch assembly WP8318084 (can stop agitation/spin on many top-load designs)
• Hose-wl WP353244 (commonly associated with water-level pressure sensing)

Why it matters

An FE overfill condition can lead to leaks, poor wash performance, and repeated drain-pump operation. Fixing the fill control issue first protects the washer cabinet, flooring, and drive components.

After the repair: confirm normal operation

Follow the setup and test steps in the 11026852504 installation guide, including leveling and running a test cycle with detergent to verify the washer fills, agitates, drains, and spins normally.

Last updated: January 2026

The exact tub capacity (cubic feet) for Kenmore washer model 11026852504 is listed in the product specifications section of the 11026852504 owner's manual. This model is a full-size top-load washer; most washers in this class are roughly 3.0 to 3.6 cu. ft. depending on the basket design.

How to find the exact capacity for 11026852504

Use the manual specs so you get the rated capacity for your specific version.

• Open the 11026852504 owner's manual
• Look for “Specifications”, “Capacity”, or “Washer dimensions”
• If the manual lists basket size by diameter and depth instead of cu. ft., use those values to compare to typical full-size top-load baskets
• Match the rating label information (model and serial) to ensure you are using the correct document

What that capacity means for real loads

Capacity is tub volume; usable load size depends on fabric type and how freely items can move for agitation.

• Mixed everyday laundry: load loosely to the top of the basket, not packed down
• Towels and denim: run smaller loads to reduce off-balance spinning
• Bulky items: wash one large item at a time if it fills more than about 2/3 of the basket

Load type	Best fill level	Why
Mixed clothes	3/4 full (loose)	Better turnover and rinsing
Towels/jeans	1/2 to 2/3 full	Helps balance and spin
Bulky bedding	1 item (varies)	Prevents strain and poor agitation

Why it matters

Using the correct capacity helps you choose the right cycle and load size; that improves cleaning, reduces vibration, and helps protect wear parts such as the clutch and suspension.

Last updated: January 2026