Frigidaire LGHB2867PF3 refrigerator Parts

On the Frigidaire LGHB2867PF3 bottom-mount refrigerator, the “bottom part” most people mean is the compressor area (the machinery compartment near the floor). That area houses key cooling components and needs clear airflow for proper operation; see the LGHB2867PF3 installation guide.

What’s typically located at the bottom

Depending on where you’re looking (front toe area vs. back lower area), the bottom section can include:

• Compressor (pumps refrigerant through the sealed system)
• Condenser fan motor (moves air across condenser coils and compressor)
• Toe grille (front lower grille that lets air circulate)
• Drain pan (collects defrost water so it can evaporate)
• Water components for the dispenser and ice maker (on many models)

Quick identification guide

Use this to match what you’re seeing to the common name.

What you see	Common name	Why it matters
Black “tank” or canister at the back bottom	Compressor	Main cooling pump; problems can stop all cooling
Fan noise from the back bottom	Condenser fan area	Poor airflow can cause warm temps and loud running
Slotted grille at the very bottom front	Toe grille	Must stay unblocked for airflow
Water line and valve near the back bottom	Water inlet valve	Affects ice maker and dispenser water

Why it matters

The bottom compartment is where heat is rejected from the refrigerator. If airflow is blocked (especially at the toe grille), the refrigerator can run longer, cool poorly, and sound louder than normal.

Helpful tips for owners

• Keep the toe grille clear; do not push rugs or boxes against it.
• Leave typical clearances for airflow (many installations use about 3/8 inch at sides/top and 1 inch at the rear).
• If you’re troubleshooting ice or water issues, check the water supply connection and look for leaks.
• For operating expectations, review the “normal operating sights and sounds” section in your guide.

Last updated: February 2026

The most common Frigidaire refrigerator problem is a cooling complaint, especially when the fresh food section warms up while the freezer still seems cold. On the Frigidaire LGHB2867PF3, this is usually tied to airflow (evaporator fan), heat removal (condenser area), or defrost-related ice buildup; water and ice maker issues are also frequent.

Most common symptoms we see

• Refrigerator section too warm, freezer OK
• Frost or ice buildup on the back wall or inside the freezer
• Loud humming, rattling, or a fan noise that comes and goes
• Ice maker not making ice or dispensing slowly
• Water dispenser flow is weak or sputters

Quick checks that solve many “not cooling” calls

1. Confirm airflow: Make sure vents inside the refrigerator are not blocked by food containers.
2. Check door sealing and leveling: Poor door alignment can cause warm temps and frost. The installation checklist calls out that doors should seal on all sides and the cabinet should be level and slightly tilted back. Use the LGHB2867PF3 installation guide for the leveling and door-alignment steps.
3. Clean heat-rejection areas: Keep the toe grille area clear because airflow is essential for proper operation.
4. Look for defrost clues: Heavy frost often points to a defrost problem (heater, sensor, or control issue).

Parts commonly involved (when symptoms match)

Symptom	Common cause	Example part for LGHB2867PF3
Warm fridge, freezer OK	Weak/no evaporator airflow	Evaporator fan blade (inspect for damage)
Slow water, poor ice production	Restricted filter or supply issue	Refrigerator water filter ULTRAWF
No ice or intermittent ice	Ice maker issue or water supply problem	Refrigerator ice maker assembly 243297613
Water won’t fill ice maker	Valve not opening fully	Refrigerator water inlet valve assembly

Why it matters

Cooling and ice maker complaints often share the same root causes: restricted airflow, poor door sealing, or water supply restrictions. Fixing the basics first prevents unnecessary part replacement and helps the refrigerator maintain stable temperatures.

Last updated: February 2026

On your Frigidaire refrigerator, the model number is printed on the appliance ID label; on LGHB2867PF3 it is typically inside the fresh food (refrigerator) compartment along the side wall or near the ceiling, and sometimes on the door frame. Match the full model number exactly when ordering parts.

Where to look first (fastest checks)

• Open the fresh food doors and check the left and right interior side walls
• Look along the door frame area behind the gasket line
• Check near the top interior ceiling panel (by the lights and controls)
• If you cannot find it in the fresh food section, check the freezer compartment side wall
• Use a flashlight; the label is often small and can be partially hidden by bins or shelves

What the label looks like

Most Frigidaire ID labels include:

• Model number (example format: LGHB2867PF3)
• Serial number (unique to your unit)
• Electrical ratings (volts/amps)
• Sometimes a bar code

You need this	Why it matters
Model number (LGHB2867PF3)	Ensures diagrams and parts match your exact configuration
Serial number	Helps confirm production variation when a part changes by revision

Why it matters for parts and troubleshooting

Frigidaire often uses similar-looking cabinets across multiple models, but parts like a water filter housing, door gasket, or user interface can vary by revision. Using the exact model number helps us match the correct replacement part the first time.

For model-specific label location notes and diagrams, use the LGHB2867PF3 owner's manual.

Last updated: March 2026