Kenmore 58715072200 dishwasher Parts

Your Kenmore dishwasher model number is printed on the model and serial number label inside the tub; on Kenmore model 58715072200, the label is on the right side of the tub when you open the door. Write down the full model number exactly as shown before ordering parts or troubleshooting.

• Open the door and look along the right interior tub wall for the model/serial label.
• Check the inner door frame area near the latch and hinges.
• Look along the top edge of the door (visible when the door is open).
• If the label is dirty or faded, wipe it gently and use a flashlight.

For this Kenmore dishwasher family, the model number is typically a long number and may appear with punctuation in the manual (for example, 587.15072). For parts lookup, use the full model number format shown on the label, such as 58715072200.

Kenmore dishwashers can share a similar look but use different components (door latch, heating element, drain hose routing, and control parts). Using the exact model number helps us match the correct diagrams and compatible parts the first time.

Once you confirm the model, the most common leak points around the door area are the lower door seal and related sealing surfaces. For Kenmore 58715072200, a common replacement is the gasket 809006501. For label location and recording model/serial details, use the 58715072200 owner's manual.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher is usually worth it when the issue is a leak, drain problem, or door-latch failure and the repair cost is reasonable compared to replacement. For Kenmore model 58715072200, many common fixes involve serviceable parts and basic troubleshooting steps in the 58715072200 owner's manual.

• Repair if the dishwasher is cleaning well overall and you’re fixing one clear failure (leak, won’t drain, won’t start).
• Repair if the problem is a wear item such as a seal, hose, or latch.
• Replace if you have repeated major failures (motor, wiring, multiple leaks) and the total repair cost approaches the price of a new unit.
• Replace if the tub or inner door panel is damaged beyond a simple seal fix.
• Repair if you can DIY safely and the part is accessible.

These are typical “high value” repairs on 58715072200 because they address frequent symptoms without replacing the whole dishwasher:

• Door leaks at the bottom edge: replace the gasket 809006501
• Won’t drain or drains slowly: inspect/replace the hose 807117001
• Won’t fill or fills slowly: check the water valve 154637401
• Door won’t latch or starts then stops: inspect the latch and strike alignment (common on many Kenmore units)

A targeted repair can extend the life of your 58715072200 and restore cleaning performance. This model’s wash system is designed to filter wash water and manage temperature for cleaning and drying; when one component (like a valve, hose, or seal) fails, the rest of the machine is often still in good shape.

Last updated: February 2026

Yes. On Kenmore dishwasher model 58715072200, you can replace the rubber door seal when it’s torn, flattened, or leaking. The job is usually straightforward: remove the racks for access, pull the old seal out, clean the channel, then press the new seal in evenly.

For the lower door sealing surface, use the correct model-matched seal:

• Gasket 809006501

1. Turn off power to the dishwasher at the breaker.
2. Open the door and slide out the upper and lower racks for working room.
3. Pull the old seal straight out of the channel (work slowly to avoid tearing pieces off in the groove).
4. Clean the seal channel and surrounding tub edge with a damp cloth; remove detergent residue and grit.
5. Press the new seal into place a few inches at a time; keep it fully seated and even end-to-end.
6. Close the door and run a short cycle to confirm the leak is gone.

• Make sure the seal is fully seated in the channel with no twists or gaps.
• Check the door closes squarely and doesn’t hit the cabinet or countertop.
• Look for food debris around the tub gasket area and wipe it clean.
• Avoid loading knives or sharp items where they can nick the seal.

A good door seal keeps wash water inside the tub, protects the floor and cabinetry, and helps the dishwasher maintain proper spray pressure for better cleaning.

For model-specific diagrams and placement details, follow the 58715072200 installation guide.

Last updated: February 2026

Yes. We still support replacement parts for Kenmore dishwashers, and for Kenmore model 58715072200 many common repair items (like door seals, drain hoses, and water inlet valves) are available. The key is matching parts to your exact model number so fit and connections are correct.

Use your model number exactly as shown on the serial label (typically on the right side of the tub) and confirm the part’s name and ID before ordering. The parts diagrams and procedures in the 58715072200 owner's manual help you identify what you’re seeing inside the tub.

• Match the full model number: 58715072200
• Identify the symptom first (leak, no drain, no fill, won’t latch)
• Compare the part name to what you’re replacing (seal vs gasket vs O-ring)
• Replace clamps or fasteners if they are corroded or distorted
• After installation, run a short cycle and check for leaks

These are frequent fixes for leaks, draining problems, and door-closing issues on this model.

Dishwashers use a sealed wash system and controlled fills; the wrong gasket, hose, or valve can cause leaks, poor cleaning, or no-start conditions. Using model-matched parts helps restore proper water flow, temperature control, and wash performance.

For safe access and correct reassembly steps, follow the 58715072200 installation guide for mounting and door handling guidance, and use the manual for operating and care details.

Last updated: February 2026