Kenmore 41743142200 washer Parts

On Kenmore washer model 41743142200, an FE code points to an overfill condition; the washer may keep filling or the drain pump may run to protect against flooding. Fixes focus on the water inlet valve shutting off correctly and the fill sensing system. See the 41743142200 owner's manual for control and cycle details.

Quick checks to stop the FE condition

• Turn off both water faucets (hot and cold) to stop incoming water.
• Unplug the washer for safety.
• If the tub is overfilled, run a Drain/Spin after restoring power and water control.
• Check that the drain hose is installed correctly with an air gap to prevent siphoning (a siphon can confuse fill behavior).

Most common causes and what to do

• Water inlet valve stuck open: If water continues to enter with power off, replace the inlet valve assembly.
• Pressure switch or air hose issue: A loose, kinked, or clogged pressure hose can prevent the washer from sensing the correct water level.
• Siphoning through the drain hose: If the drain hose is shoved too tightly into a standpipe or lacks a proper U shape, the washer can drain while filling and keep trying to refill.

Parts that are often involved

Symptom	Likely part/system	What you’ll notice
Water keeps flowing when washer is off	Water inlet valve	Tub slowly fills on its own
Fills too long, then errors	Pressure sensing (switch/hose)	No obvious leak, but level never “registers”
Fills and drains at the same time	Drain hose setup	Gurgling, inconsistent fill level

If you confirm the valve is the issue, the correct replacement for this model is the washer valve 134190200.

Why it matters

An FE overfill condition can lead to leaks, poor wash results, and repeated drain pump operation. Correcting the inlet valve or the drain hose installation prevents water waste and protects the door lock and control system.

Last updated: January 2026

For the Kenmore 41743142200 washer, a hard reset is done by disconnecting power long enough for the control to fully power down, then restoring power and restarting a cycle. This clears many temporary control glitches and lets the washer restart normally (use the 41743142200 owner's manual for model-specific control behavior).

Hard reset steps (recommended)

• Press the cycle selector knob in to stop the washer.
• Unplug the washer (or switch the breaker OFF).
• Wait 2 minutes.
• Restore power.
• Select a normal cycle and start the washer.

If the washer still will not start after a reset

These checks solve the most common “dead” or “won’t start” symptoms on this front-load design:

• Confirm the power cord is fully seated in the outlet.
• Check the house breaker or fuse and reset if tripped.
• Make sure the door is fully closed; the door locks during operation.
• Make sure the dispenser drawer is completely closed.
• If the motor overheated, wait up to 30 minutes for the overload protector to reset, then try again.

What a hard reset can and cannot fix

Situation	Hard reset helps?	What to do next
Control glitch, cycle won’t respond	Yes	Power reset, then restart cycle
Door will not lock	Sometimes	Inspect latch alignment; consider door catch 131763256
Washer stops mid-cycle from overheating	No (by itself)	Let it cool up to 30 minutes, improve airflow
Repeated drain or fill problems	Sometimes	Check hoses, pump, and inlet screens

Why it matters

A hard reset is the fastest safe first step because it removes “stuck” control logic without disassembly. If the issue returns immediately, the symptom usually points to a door-locking problem, an overheated motor condition, or a power supply issue rather than a one-time glitch.

Last updated: January 2026

Most Kenmore washers last 10 to 15 years with normal household use; your Kenmore 41743142200 front-load washer can often reach that range when it is installed correctly, kept level, and maintained (especially the door area and drain system). See the 41743142200 owner's manual for model-specific care and cleaning steps.

Typical lifespan and what affects it

A washer’s service life depends more on use and maintenance than the brand name on the console.

• Loads per week: more cycles equals faster wear on bearings, shocks, and the drain pump
• Overloading: increases vibration and stress on the tub and suspension
• Detergent use: too much HE detergent can cause residue and odors that lead to extra cleaning and service
• Water quality: hard water can accelerate buildup in valves and hoses
• Leveling and installation: an unlevel washer can shorten the life of shocks and other moving parts

Maintenance that helps a Kenmore front-load washer last longer

Use these habits to reduce leaks, odors, and vibration issues.

• Wipe the door boot and glass dry after laundry day
• Leave the door slightly open between loads to help the tub dry
• Run a monthly cleaning cycle (or hot wash) to reduce residue
• Check the drain path if you notice slow draining or standing water
• Keep the washer level; recheck if it starts walking or shaking

Common wear items (and what they usually cause)

Part or system	Common symptom	Example model-matched part
Door lock/catch	Door won’t latch, won’t start	Door catch 131763256
Drain system	Won’t drain, long drain times	Washer drain pump 137108000
Suspension/shocks	Excessive vibration, banging	Level shock 5304485917

Why it matters

A washer that is kept clean, level, and not overloaded typically runs quieter, drains better, and avoids repeat breakdowns; that is what most often separates a 7-year washer from a 15-year washer.

Last updated: January 2026