Frigidaire FFSC2323LS1 refrigerator Parts

For a Frigidaire FFSC2323LS1 side-by-side refrigerator, we troubleshoot by confirming power, verifying temperature settings, checking door sealing and airflow, and cleaning heat-transfer surfaces. If the unit still has issues after these basics, use the model’s built-in “Solutions to Common Problems” steps in the FFSC2323LS1 owner’s manual.

• Make sure the plug is fully seated in the outlet.
• Check the home breaker or fuse (use a 15-amp time-delay fuse if applicable).
• Confirm the Fresh Food and Freezer temperature settings are set (then allow 24 hours to stabilize after changes).
• Verify doors close completely; keep food packages from blocking the door.
• Inspect and clean the door gaskets; leaks make the refrigerator run longer.
• Clean the condenser area; a dirty condenser can cause poor cooling and long run times.

If cooling is OK but ice or water performance is off, we start with installation basics:

• Confirm the house water supply is connected and not leaking.
• Make sure the ice maker is turned ON.
• Check that the water filter above the fresh food compartment is fully seated.

Helpful how-to: how to replace the water filter in a Frigidaire refrigerator.

A fully automatic defrost refrigerator runs a defrost cycle periodically (about 30 minutes). During that time, temperatures and run patterns can look different than usual.

These checks prevent unnecessary part replacement and protect major components like the compressor; low or inconsistent power can damage the compressor, and door seal leaks force longer run times.

Last updated: January 2026

On the Frigidaire FFSC2323LS1 side-by-side refrigerator, CF indicates the electronic control system has detected a performance or communication problem, so the refrigerator may not cool correctly or may show flashing temperature displays. Follow the checks below, then use the diagnostic guidance in the FFSC2323LS1 owner’s manual.

• Reset power: unplug the refrigerator (or switch off the breaker) for 5 minutes, then restore power.
• Confirm the outlet has power and the cord is fully plugged in.
• Make sure the doors close and seal completely; warm air leaks can trigger performance issues.
• Verify the water filter is fully seated (it should sit flush and click into place).
• Allow 24 hours after any reset or temperature change for temperatures to stabilize.

CF is most often tied to a control-related issue such as a loose connection, wiring problem, or a failing control board. If the code returns after the quick checks, focus on the control and sensor side of the cooling system.

When CF is active, the refrigerator may run longer, cool unevenly, or stop maintaining safe food temperatures. Addressing door sealing, airflow, and control feedback (sensor signals) prevents unnecessary compressor run time and helps restore stable cooling.

If CF returns immediately after a power reset, or if the refrigerator is not cooling after 24 hours, we recommend professional diagnosis because live-voltage testing and sealed-system checks may be required.

Last updated: January 2026

For the Frigidaire FFSC2323LS1 side-by-side refrigerator, the most reliable reset is a power reset: unplug the refrigerator (or switch off the breaker) for about 5 minutes, then restore power. For control-related issues, you can also turn cooling off and back on from the user interface as described in the FFSC2323LS1 owner's manual.

• Power reset (best for glitches): unplug for ~5 minutes, then plug back in.
• Cooling system reset (panel-based): press and hold power on/off for 3 seconds to turn cooling OFF; press and hold again for 3 seconds to turn cooling back ON.
• Filter light reset (after replacing filter): press and hold water filter (or filter reset, depending on display style) for 3 seconds.
• Dispenser lock check: press and hold control lock for 3 seconds to unlock if the dispenser seems “dead.”

1. Move any perishable items to a cooler if you expect the unit to be off longer than a few minutes.
2. Unplug the power cord from the wall outlet (or turn off the circuit breaker).
3. Wait 5 minutes.
4. Restore power and allow 24 hours for temperatures to fully stabilize.

A reset clears minor electronic glitches and restores normal control logic, but it will not correct mechanical issues like a dirty condenser, a leaking door gasket, or a water supply problem. Using the correct reset method helps you avoid unnecessary part replacement.

For model-specific button locations and display behavior, follow the control panel details in the FFSC2323LS1 owner's manual.

Last updated: January 2026

If your Frigidaire FFSC2323LS1 side-by-side freezer isn’t freezing, the most common causes are restricted airflow (blocked vents or a weak evaporator fan), warm air leaking past the door seal, or a cooling/defrost issue that prevents the freezer from staying cold enough.

• Confirm the freezer temperature is set correctly and give changes 24 hours to stabilize.
• Make sure the freezer door closes fully and seals to the cabinet on all sides.
• Verify the refrigerator is level and tilted about 1/4 inch (6 mm) front-to-back so doors self-close.
• Check that vents inside the freezer are not blocked by food packages.
• Listen for the evaporator fan running when the door is closed (you may hear airflow).

These parts are often involved when temperatures rise or airflow is weak:

• Refrigerator evaporator fan blade 5308000010 (air movement across the evaporator)
• Refrigerator temperature sensor 240597220 (reports temperature to the control)
• Refrigerator defrost bi-metal thermostat 5303918214 (helps control defrost heating)

A side-by-side like the FFSC2323LS1 depends on steady airflow from the freezer to maintain freezing temperatures. If airflow is restricted or warm air leaks in, the freezer warms quickly and food safety becomes a concern.

For model-specific operating settings, leveling guidance, and “normal sounds” versus problem symptoms, use the FFSC2323LS1 owner’s manual.

Last updated: January 2026