Installation guide
Owner’s manual
Error Codes
Who makes the Roper washer?
Roper washers (including model RAS7133RQ4) are made by Whirlpool Corporation and sold under the Roper brand. You will often see Whirlpool referenced in the documentation and parts system because Whirlpool is the manufacturer behind the Roper product line.
The RAS7133RQ4 documentation is branded and published by Whirlpool Corporation, which is a clear indicator of who manufactures the washer.
- The user instructions show Roper branding with Whirlpool Corporation as the publisher
- Service and assistance references point to Whirlpool support channels in the manual
- Replacement parts guidance references factory-specified parts used for Roper appliances
Knowing Whirlpool is the manufacturer helps you match the correct replacement parts and repair procedures for your Roper washer.
Common Whirlpool-built, direct-drive style washer parts you may see for RAS7133RQ4 include:
- Washer lid switch assembly WP8318084 (if the washer will not spin with the lid closed)
- Washer drain pump WP3363394 (if the washer will not drain)
- Washer motor coupling 285753A (if the motor runs but the tub will not agitate or spin)
| Brand on the washer | Manufacturer behind the brand | What to use for repairs |
|---|---|---|
| Roper | Whirlpool Corporation | Model number RAS7133RQ4 and the parts list for that model |
For model-specific identification, safety info, and operating details, use the owner's manual.
Last updated: February 2026
How long does a roper washer last?
A Roper washer like model RAS7133RQ4 typically lasts 10 years. You can often extend that lifespan by keeping the washer level, avoiding overloads, cleaning the tub and dispensers regularly, and replacing wear items (like inlet hoses) on schedule.
Most washers average about 10 years of service. What usually shortens life is chronic overloading, running unbalanced loads, and small leaks that go unnoticed.
Common life-extenders for RAS7133RQ4:
- Keep the washer level to reduce vibration and suspension wear
- Wash balanced loads (mix items, avoid single heavy pieces)
- Clean the washer interior periodically (hot cycle cleaning)
- Inspect for leaks at hoses, drain connections, and tub area
- Replace inlet hoses on a schedule (see the owner's manual)
Use this quick routine to keep performance strong year after year:
- Monthly: wipe spills, run a hot cleaning cycle when odors build up
- Every load: avoid overfilling; distribute items evenly
- Every few months: check fill hoses for bulges, cracks, or seepage
- At 5 years: replace inlet hoses to reduce the risk of hose failure
- Anytime: correct rocking or shaking by re-leveling (see the installation guide)
These symptoms often show up as major drive, drain, or spin wear:
| Symptom | What it often points to | Example part on this model |
|---|---|---|
| Won’t spin or agitates poorly | drive system wear | Washer motor coupling 285753A |
| Won’t drain or drains slowly | drain pump issue or blockage | Washer drain pump WP3363394 |
| Stops mid-cycle or won’t run with lid closed | lid switch problem | Washer lid switch assembly WP8318084 |
A washer that is kept level, leak-free, and not overloaded runs with less strain on the motor, clutch, suspension, and seals. That reduces breakdowns and helps your RAS7133RQ4 reach (or beat) the typical 10-year lifespan.
Last updated: February 2026
What are the common problems with Roper washing machines?
Common problems on a Roper washer like model RAS7133RQ4 include not draining or spinning (often tied to the lid being open, a drain hose setup issue, or excess suds), shaking from an unbalanced load or leveling problem, and filling issues caused by hose or water-supply problems. See the owner's manual for the model-specific troubleshooting checks.
- Won’t drain or spin: Confirm the lid is fully closed; the washer will not agitate or spin with the lid open.
- Slow drain or no drain: Check for a kinked or clogged drain hose; verify the drain hose height is not more than 96 in. (244 cm) above the floor.
- Cycle seems stuck (fills and drains): Make sure the top of the drain hose is higher than the washer’s water level; keep an air gap (do not tape or seal the standpipe connection).
- Shaking or walking: Balance the load, avoid overloading, and level the washer; tighten the front feet locknuts and reset rear leveling legs if needed.
- “Not filling enough” concern: A high agitator top compared to the water level is normal on this design.
If the basic checks above do not fix the issue, these parts are frequent repair solutions for this model:
| Symptom | Common part to inspect/replace | What it affects |
|---|---|---|
| Won’t spin or agitate | Washer lid switch assembly WP8318084 | Stops spin/agitate when lid is open or switch fails |
| Won’t drain | Washer drain pump WP3363394 | Pumps water out during drain/spin |
| Won’t agitate/spin, motor runs | Washer motor coupling 285753A | Connects motor to transmission/drive |
| Won’t fill or fills slowly | Washer inlet valve 285805 | Controls hot/cold water entering the tub |
Most “major” washer complaints are caused by setup or safety interlocks, not the motor or gearcase. Correct drain hose height, a level cabinet, and a working lid switch prevent no-spin, no-drain, and out-of-balance problems that leave clothes wet.
- Measure detergent to prevent excessive sudsing.
- Load items loosely; do not wrap items around the agitator.
- Keep the washer level and loads balanced to reduce vibration.
- Ensure hot and cold hoses are connected to the correct faucets.
Last updated: February 2026
