Craftsman 917376220 lawn mower Parts

Common problems on the Craftsman walk-behind mower model 917376220 usually come down to starting issues (fuel, spark, or safety controls), loss of power from airflow or deck buildup, excessive vibration from a damaged or loose blade, and drive problems on self-propelled units. Our 917376220 owner's manual troubleshooting chart covers these symptoms and the fastest checks.

Most common symptoms and what they usually mean

• Won’t start: dirty air filter, stale fuel, water in fuel, disconnected spark plug wire, bad spark plug, or the control bar not held against the handle.
• Loss of power: cutting too much grass at once, dirty air filter, grass and debris packed under the deck, or too much oil in the engine.
• Poor cut quality: worn, bent, or loose blade; uneven wheel height settings; heavy buildup under the mower deck.
• Excessive vibration: bent or loose blade, damaged blade adapter, or a bent crankshaft after striking an object.
• Hard to push or loss of drive (power-propelled): drive control cable out of adjustment, worn drive components, or transmission wear.

Quick checks we recommend before buying parts

1. Confirm the control bar is fully depressed to the handle while starting.
2. Drain old fuel and refill with fresh gasoline; stale fuel is a top cause of no-start.
3. Inspect the blade and underside of the deck; clean packed grass and check for damage.
4. Check the blade mounting hardware and tighten if loose; replace damaged parts.
5. Inspect self-propel drive engagement; if it slips, check the cable and drive parts.

Parts that commonly solve these problems

Symptom	Common fix	Example part for 917376220
Vibration, poor cut	Replace a worn/bent blade	Lawn mower 22-in deck 3-in-1 blade 532420463
Loss of drive	Restore drive engagement	Lawn mower drive control cable 588479201
Poor discharge/bagging	Replace damaged rear door/deflector parts	Lawn mower clipping deflector 532426129

Why it matters

These issues affect safety and cut quality. For example, a loose or bent blade can cause severe vibration and damage the crankshaft, while deck buildup can choke airflow and reduce engine power.

Model-specific notes for 917376220

• The manual notes the carburetor is not adjustable and engine speed is factory set; if the engine runs abnormally fast/slow, service is the right next step.
• For storage-related problems (stale fuel, corrosion), follow the storage steps in the manual to prevent repeat no-start issues.

Last updated: February 2026

The Craftsman model 917376220 uses a Briggs & Stratton 650 Series engine (as shown in the model’s owner’s manual). This mower is a power-propelled, 22-inch multi-cut rotary walk-behind design with an operator presence control bar for safe operation.

Where to confirm the exact engine details

We recommend using the model documentation to match the engine family and service parts (air filter, spark plug, carburetor parts) to the engine’s ID label.

• Check the cover page and specifications in the 917376220 owner's manual
• Locate the engine model/type/code on the engine shroud or valve cover label
• Use the engine ID (not just mower model) when ordering engine-specific parts
• Keep the operator presence control bar functioning; the blade turns when the engine runs

Quick reference: mower model vs. engine identification

Item	What it identifies	Where to find it	Used for
Mower model 917376220	The Craftsman mower platform	Mower deck tag or paperwork	Mower chassis parts (wheels, cables, blade, bagging parts)
Briggs & Stratton 650 Series	The engine series family	Manual cover and engine shroud	Engine tune-up parts and engine service info
Engine model/type/code	The exact engine build	Engine label/stamp	Correct spark plug, air filter, carb parts

Related parts you might replace on this mower

If you are servicing the cutting system or drive system on this 22-inch deck mower, these model-matched parts are common:

• Lawn mower 22-in deck 3-in-1 blade 532420463 for cutting, mulching, and bagging performance
• Husqvarna lawn mower zone control cable 532420939 if the engine control cable is stretched or damaged
• Lawn mower drive control cable 588479201 if self-propel engagement is inconsistent

Why it matters

Briggs & Stratton “series” names (like 650 Series) narrow the engine family, but the engine model/type/code is what ensures you get the right maintenance parts and settings for starting, fuel, and ignition.

Last updated: February 2026

For the Craftsman lawn mower model 917376220, we use SAE 30W engine oil; the initial fill is 18 oz, and an oil change typically takes about 20 oz. Check the dipstick level before each use and fill only to the full mark (do not overfill). See the 917376220 owner's manual for the oil section and maintenance intervals.

Oil type and capacity for model 917376220

• Oil type: SAE 30W (small engine 4-cycle oil)
• Initial fill: 18 oz (new mower first fill)
• Refill after draining (oil change): about 20 oz
• Check frequency: before each use
• Change interval: every 25 hours of operation or each season

Quick reference

Task	Amount to add	What to do next
First time adding oil (new mower)	18 oz	Install dipstick, then recheck level
Routine oil change	~20 oz	Run briefly, shut off, recheck dipstick
Topping off	Small amounts	Recheck often to avoid overfill

How we recommend filling oil (no mess, no overfill)

1. Park the mower on a level surface.
2. Remove the oil cap/dipstick and wipe it clean.
3. Add oil slowly (start with about 16 oz if you are unsure how much is in the crankcase).
4. Reinsert the dipstick, then pull it and confirm the level is at the full line.
5. Add small amounts until full; stop as soon as it reaches the mark.

Why it matters

Using the correct SAE 30W oil and the right fill amount helps prevent hard starting, smoking from overfill, and accelerated engine wear on the Briggs & Stratton-powered 650 Series engine used on this mower.

Last updated: February 2026

The model number for a Craftsman 917376220 lawn mower is 917.376220 (often written without the dot as 917376220). On this mower, the model and serial number are listed on a decal on the rear of the mower housing; confirm it there and in the 917376220 owner's manual.

Where to find the model number on the mower

Look for the identification decal in these common spots:

• Rear of the lawn mower housing (most common on this model)
• Near the rear door or discharge area
• On the deck near the wheel height adjuster
• On the handle bracket area

Why you might see a different number online

Craftsman walk-behind mowers can look similar across multiple model numbers, and listings sometimes mix them up. For parts and diagrams, the exact model number matters because it controls the correct blade, drive system, and handle hardware.

What you see	What it means	What to do
917.376220	Full model format with dot	Use this for manuals and parts lookups
917376220	Same model without dot	Also acceptable for searches
A different 917.xxxxx number	Different mower configuration	Re-check the rear housing decal

Why it matters (parts fit and repairs)

Using the correct model number helps us match the right Craftsman parts for your mower, especially for high-fit items like the blade and self-propel drive components.

Common model-specific parts you may need include:

• Lawn mower 22-in deck 3-in-1 blade 532420463 (cut quality and vibration issues)
• Drive control cable (self-propel not engaging)
• Wheel dust cover and drive pawl (drive wheel slipping)
• Grass bag frame and discharge components (bagging and rear door fit)

Last updated: February 2026

On the Craftsman walk-behind mower model 917376220, the model and serial numbers are printed on a decal on the rear of the lawn mower housing. Use that model number when ordering non-engine parts like the blade, drive cable, or wheels; see the 917376220 owner's manual for the exact decal location.

Where to look on the mower

Check these common spots first (rear housing is the primary location for this model):

• Rear of the mower deck or housing (look for a decal/label)
• Near the rear discharge door area
• On the handle support area close to the deck
• On the side of the deck near the wheel height adjusters
• Under grass buildup; wipe the area clean to reveal the label

What to write down (and why)

Record both numbers from the decal so we can match the correct Craftsman parts list.

Item on the decal	Example format	What we use it for
Model number	917.376220	Identifies the mower and its parts diagrams
Serial number	Varies	Helps confirm production run and correct part variations

Tips if the label is hard to read

A faded or dirty decal is common on walk-behind mowers.

• Brush off dried grass and dirt; then wipe with a damp rag
• Use a flashlight at a low angle to make embossed printing easier to see
• Take a close-up photo and zoom in
• If only part of the number is visible, look for the full “917.” prefix pattern

Why it matters

Craftsman mowers often share similar decks and handles across model families, but parts like the drive control cable, discharge deflector, and blade can differ. Using the exact model number helps ensure the right fit the first time.

Last updated: February 2026