Owner’s manual
Error Codes
How much does it cost to replace a gas shut off valve on a dryer?
Replacing the gas shutoff valve for a Kenmore gas dryer model 11094821300 typically costs $20 to $75 for the valve plus labor, which commonly brings the total to about $150 to $350 depending on access, local rates, and whether the gas line needs updates to meet code. See the 11094821300 owner's manual for shutoff valve location guidance.
- Valve type and size (common household gas shutoff valves are inexpensive, but specialty fittings add cost)
- Labor time (tight laundry closets and rigid piping increase time)
- New connector or fittings (a new flexible connector is often used during rework)
- Leak testing (every connection must be checked with an approved leak-detection solution)
- Local code requirements (for example, shutoff valve placement and approved materials)
For this Kenmore gas dryer, the shutoff valve is normally installed within 6 feet of the dryer and should be easy to reach for opening and closing. The valve is open when the handle is parallel to the gas pipe. Those details help a technician estimate access time and whether the existing valve placement is acceptable. Refer to the 11094821300 owner's manual.
| Cost item | Typical range | Notes |
|---|---|---|
| Gas shutoff valve (part) | $20 to $75 | Part cost varies by style and supplier |
| Labor | $100 to $250 | Often 1 to 2 hours depending on access |
| Fittings/connector (if needed) | $10 to $50 | May be needed when reworking the gas line |
| Total installed | $150 to $350 | Common real-world range |
Because this is a gas connection, we recommend professional service unless you are fully qualified.
- A pro will shut off gas safely and confirm the valve is installed correctly
- A pro will leak test every joint after installation
- A pro can correct issues like kinked flexible tubing or improper fittings
A properly working, easy-to-reach shutoff valve lets you safely stop gas flow for moving, maintenance, or troubleshooting a no-heat condition. It also helps prevent leaks by ensuring connections are tightened and tested correctly.
Last updated: January 2026
Does a gas dryer need a special outlet?
No. The Kenmore gas dryer model 11094821300 plugs into a standard grounded 120-volt, 3-prong outlet (15- or 20-amp). It does not use the 240-volt outlet that most electric dryers require; the gas supplies the heat and the outlet powers the motor and controls (see the 11094821300 owner's manual).
Use these requirements when choosing the outlet location and circuit:
- Grounded 3-prong receptacle
- 120-Volt, 60-Hz, AC-only power
- 15- or 20-amp fused electrical supply
- No adapter, no extension cord, and do not remove the ground prong
- Outlet should be within about 2 ft of either side of the dryer
A gas dryer’s special requirements are the gas and venting, not the electrical outlet.
| Requirement | Gas dryer (11094821300) | Typical electric dryer |
|---|---|---|
| Electrical outlet | 120V grounded 3-prong | 240V dryer receptacle |
| Heat source | Natural gas or LP | Electric heating element |
| Venting | Must exhaust outdoors | Usually exhaust outdoors |
Using the correct grounded 120V outlet helps prevent nuisance tripping, control issues, and shock hazards. Separately, proper venting and a correctly installed gas shutoff valve help the dryer heat safely and dry efficiently.
- Confirm the outlet is grounded and not controlled by a wall switch
- Use a dedicated circuit if possible
- Keep the vent from being crushed or kinked when you push the dryer back
- On gas models, verify the flexible gas line is not kinked and connections are leak-tested
Last updated: January 2026
Is a gas dryer 120 or 240?
A Kenmore gas dryer like model 11094821300 typically uses a standard 120-volt household outlet to run the motor, controls, and igniter; the heat source is gas, not 240-volt electric heat. Confirm the exact electrical requirements in the 11094821300 owner's manual.
Most gas dryers are designed to run on 120 VAC and do not use a 240-volt dryer receptacle.
- Uses 120 VAC for the timer/control board, drum motor, and blower
- Uses gas for heating (natural gas or LP with proper conversion)
- Plugs into a standard grounded outlet located near the dryer
- Does not use a 30-amp 240-volt dryer cord like most electric dryers
- Still requires proper venting to the outdoors for safe operation
| Dryer type | Typical outlet voltage | Typical circuit | What makes the heat |
|---|---|---|---|
| Gas dryer (like 11094821300) | 120 V | 15 to 20 amp | Gas burner + igniter |
| Electric dryer | 240 V | 30 amp | Electric heating element |
Using the correct voltage and outlet prevents nuisance no-start issues, protects the dryer’s controls, and helps ensure safe grounding. For gas models, correct installation also includes proper gas supply connection and outdoor venting.
The manual for this Kenmore gas dryer also calls out key safety and installation items that go along with the electrical hookup:
- Use a properly grounded outlet near the dryer
- Install a gas shut-off valve within the recommended distance
- Use an approved new gas supply line/connector
- Keep lint buildup under control; clean the exhaust vent periodically
- Exhaust a gas dryer to the outdoors
Last updated: January 2026
