Whirlpool 2DWTW4705EW2 washer Parts

The most common Whirlpool washer problems are draining or spinning issues (clothes stay wet), water leaks, and excessive shaking or noise. On your Whirlpool 2DWTW4705EW2, these symptoms often trace back to the drain system, lid locking, suspension, or shifting components.

Most common symptoms and what they usually mean

• Won’t drain or won’t spin: drain pump issue, kinked drain hose, or a lid lock that is not engaging
• Leaking water: loose hose connections, a worn drain hose, or a failing pump
• Loud banging or walking: unbalanced load or worn suspension/dampers
• Won’t start or stops mid-cycle: lid lock problem or shifting/actuator issue
• Agitates poorly: drive block or gear case wear

Quick checks we recommend first (no parts needed)

1. Redistribute the load and run a Spin/Drain cycle again.
2. Confirm the washer is level on the floor; re-level the feet if needed.
3. Check the drain hose routing for kinks, clogs, or an overly tight standpipe.
4. Listen during drain: a loud hum with little water flow points to a pump or blockage.
5. Watch the lid lock: if the lid never locks, the washer may refuse to spin.

Parts that commonly fix these problems on model 2DWTW4705EW2

Symptom	Common part to check	What it affects
Won’t spin / won’t start	Lar, 120v pi W11307244	Lid locking and spin enable
Shakes, bangs, off-balance	Damper assembly W10780045	Tub suspension and vibration control
Won’t drain	Water pump WPW10297342	Draining water from the tub
Won’t shift between agitate and spin	Actuator, shift W11481722	Shifting the drive system

Why it matters

Drain, spin, and vibration problems can quickly turn into bigger wear issues (gear case, basket, tub components) if the washer keeps running out of balance or with poor draining. Catching the root cause early helps protect the drive system and reduces repeat breakdowns.

Last updated: February 2026

To reset the lid lock on your Whirlpool washer model 2DWTW4705EW2, we recommend starting with a power reset and a simple lid check. If the washer still shows a lid lock problem, the lid lock assembly or lid strike is often the cause and may need replacement.

Quick reset steps (most common)

• Unplug the washer (or turn off the breaker) for 5 minutes.
• Restore power.
• Lift and close the lid firmly, then try Start again.
• If the lid was recently slammed or forced open, inspect the strike and lock for cracks or looseness.

If the lid still will not lock or unlock

These checks help you decide whether you are dealing with a control reset issue or a failed lock/strike.

• Make sure the lid is closing squarely; a tilted cabinet can prevent the lock from aligning.
• Listen for a click when the washer tries to lock; no click often points to a failed lock or broken strike.
• Check for a loose or broken lid strike; replace it if worn.
• If the washer will not start and the lid lock light stays on, the lock assembly can be sticking internally.

Parts that commonly fix lid lock problems

Symptom	Most likely part	Model-matched part to consider
Lid will not lock, no click	Lid lock assembly	Lar, 120v pi W11307244
Lid closes but does not “catch”	Lid strike	Strike pima W10837741

Why it matters

The lid lock is a safety switch; if it does not confirm the lid is closed and locked, the washer can stop, refuse to spin, or get stuck mid-cycle. Fixing the lock alignment or replacing a worn lock/strike restores normal cycle operation.

Helpful DIY reference

If your washer is showing an error code along with the lid lock issue, use our Whirlpool compact top load washer error codes guide to narrow down the failure and the most likely repair.

Last updated: February 2026

Yes. In a Whirlpool washer like model 2DWTW4705EW2, using too much detergent can create excess suds that interfere with water-level sensing and draining; the washer may pause, try to protect against overflow, and trigger an E3-type drain/overfill error.

What to do right now

• Press Pause/Cancel to stop the cycle.
• Let suds settle for 30 to 60 minutes with the lid closed.
• Run a Rinse/Spin (or Drain/Spin) with no detergent.
• If suds remain, run an additional rinse using cold water.
• Reduce detergent next load (HE detergent only; measure carefully).

Why too much detergent triggers E3 symptoms

Too many suds can trap air and slow water flow, which makes the washer behave like it is overfilled or not draining correctly.

Common results include:

• Longer drain times
• Repeated attempts to drain
• Poor spin performance (clothes stay wet)
• Error codes related to water level or draining

If the error keeps coming back (even with correct detergent)

Excess suds is common, but repeated E3-type errors usually point to a real drain or lock issue.

What you notice	Most likely cause	What to check next
Won’t drain or drains very slowly	Drain restriction or weak pump	Kinked hose, standpipe height, pump noise
Stops and won’t spin	Lid not locking consistently	Lid strike alignment, lock engagement
Loud banging, off-balance, won’t complete spin	Suspension not controlling tub movement	Leveling, load size, suspension wear

Parts that commonly relate to E3-type drain/spin problems on this model

• Hose asm - d W11244231 (drain hose; check for kinks, clogs, or poor routing)
• Water pump WPW10297342 (if the pump hums but won’t move water, or leaks)
• Lar, 120v pi W11307244 and strike pima W10837741 (lid lock and strike; spin can stop if the lid won’t lock)
• Damper assembly W10780045 (if the tub swings excessively and the washer aborts spin)

Why it matters

Using the right detergent amount prevents false water-level and drain faults, improves rinsing, and helps protect components like the pump, lid lock, and gearcase from extra strain.

Last updated: February 2026