Kenmore Elite 66513962K013 undercounter dishwasher Parts

To reset the control on your Kenmore Elite dishwasher model 66513962K013, we recommend using the built-in reset sequence: press CANCEL/DRAIN twice, then choose a new cycle and press START/RESUME. This clears the current cycle and restarts the control logic. See the 66513962K013 owner's manual for the exact button sequence.

• Open the door slightly to pause the cycle; wait for spraying to stop.
• Open the door fully.
• Press CANCEL/DRAIN two times to reset the control.
• Select your new cycle and any options.
• Press START/RESUME.

If there is water sitting in the bottom, use the cancel and drain procedure:

• Open the door slightly to stop the cycle; wait for spraying to stop.
• Press CANCEL/DRAIN once.
• Close the door within 3 seconds so the drain cycle can run.
• Let it drain completely (the cancel/drain indicator typically turns off after about 2 minutes).

Resetting the control is the fastest way to recover from a stuck cycle, flashing option lights, or a cycle you want to restart. If the dishwasher still will not drain or refill after a reset, the issue is usually mechanical (filter restriction, drain hose routing, or a failing pump/valve).

• Dishwasher drain pump WPW10348269 (moves water out of the tub)
• Dishwasher drain hose 8269144A (carries drain water to the sink drain or disposer)
• Dishwasher filter W10872845 (helps prevent debris from reaching the pump)

Last updated: January 2026

On the Kenmore Elite dishwasher model 66513962K013, the AE code (often paired with E1) points to a water-level problem: the circulation pump can run abnormally fast when the tub water level is too low, or water in the base can trip the flood switch. Follow the reset and leak checks in the 66513962K013 owner’s manual.

• Press Cancel/Drain (if the controls respond) to stop the cycle.
• Unplug the dishwasher or switch OFF the breaker.
• Shut off the water supply valve under the sink.
• If you see water on the floor, dry it up to prevent slipping.
• Wait 5 minutes, then restore power and try a quick cycle to see if the code returns.

AE is usually triggered by one of these conditions:

• Low water level in the tub (fill problem)
• Water in the base pan (leak or overflow tripping the float or flood switch)
• Drain issue that leaves the unit partially empty during wash
• Suds/over-foaming from the wrong detergent (hand soap or too much detergent)

AE is a protection signal. Running with low water level can reduce cleaning performance and strain the wash system; water in the base indicates a leak condition that can keep the dishwasher from operating normally.

Last updated: January 2026

On the Kenmore Elite dishwasher model 66513962K013, the F4E1 service code points to a wash motor or wash pump problem (the dishwasher is not circulating water correctly). In most cases, the fix is to diagnose the wash motor circuit and replace the failed motor/pump component, then clear the code using the reset steps in the 66513962K013 user manual.

• Dishes come out dirty because spray pressure is weak or missing
• You hear a drain pump running, but little or no “wash” sound during the cycle
• The unit may fill and then stop washing, or end early with a service message
• Water may be present in the tub but not moving through the spray arms

Turn off power at the breaker before any inspection.

• Confirm the dishwasher is getting water (listen for fill at the start)
• Check for a clogged filter and clean it if needed (a restricted filter can reduce circulation)
• Make sure spray arms can spin freely and are not blocked by tall items
• Run a Cancel/Drain and restart a cycle to see if the code returns immediately

If the dishwasher fills but does not circulate, these are common suspects:

Many Kenmore Elite dishwashers require a keypad sequence to exit a service state after the underlying problem is corrected. Use the exact reset procedure and button sequence shown in the 66513962K013 user manual.

When the wash motor is not circulating water, detergent cannot dissolve and spray arms cannot clean properly. Continuing to run cycles with an F4E1 condition typically leads to repeated service codes and consistently poor cleaning.

Last updated: January 2026

Common problems on the Kenmore Elite 66513962K013 dishwasher include not starting or stopping mid-cycle (door not fully latched or Start/Resume blinking), not draining (kinked hose or disposer knockout plug still in place), poor cleaning from hard water buildup, and detergent not dispensing when items block the wash system. See the 66513962K013 owner's manual for model-specific troubleshooting steps.

• Dishwasher does not run: door not closed and latched, Start/Resume light blinking, cycle not selected, or a tripped breaker/fuse.
• Detergent remains in the dispenser: loading blocks the wash system or dispenser area; cycle pauses are normal.
• Not draining: kinked drain hose, food obstruction in drain/disposer, or disposer knockout plug not removed.
• Hard water residue or cloudy glassware: mineral deposits; rinse aid missing; filters need cleaning.
• Odors or noisy operation: food debris in filtration area or drain path; occasional noise from normal water movement.

1. Confirm the door closes fully and latches; if Start/Resume is blinking, close the door and press START/RESUME.
2. Verify power: check the house breaker or fuse.
3. If connected to a food waste disposer, confirm the disposer inlet knockout plug was removed.
4. Inspect the drain hose for kinks and check for food obstructions.
5. Address hard water: incoming water should be at least 120°F (49°C); use rinse aid and clean the filtration system regularly.

Most “dishwasher problems” on the 66513962K013 trace back to airflow and waterflow basics: a fully latched door, correct fill temperature, clear drain path, and a clean filtration system. Fixing those first prevents repeat clogs, poor wash results, and unnecessary part replacement.

Last updated: January 2026