Amana AFI2538AES refrigerator Parts

To reset the ice maker on your Amana AFI2538AES, turn the ice maker switch OFF, then back ON, and allow time for a new harvest cycle. If you need a full reset, unplug the refrigerator for 1 minute, restore power, and confirm the ice maker is switched ON.

Quick reset steps (most common)

• Make sure the ice bin is seated fully.
• Turn the ice maker switch to OFF.
• Wait 10 seconds.
• Turn the switch back to ON.
• Discard the first 3 harvests after restarting (or any ice made in the first 12 hours).

Full power reset (when it is unresponsive)

1. Unplug the refrigerator (or switch off the breaker).
2. Wait 1 minute.
3. Restore power.
4. Verify the ice maker switch is ON.
5. Give the unit time to make ice; most refrigerators need several hours to refill the mold and drop cubes.

What to check if it still will not make ice

• Water supply valve is fully open and the line is not kinked.
• Freezer temperature is cold enough; most ice makers need about 0°F to cycle normally.
• Filter or bypass is installed correctly; after filter changes, run water to purge air.
• Ice maker shutoff arm (if equipped) moves freely and is not stuck in the up position.
• If the ice maker is physically damaged or not cycling, replacement is often the fastest fix: refrigerator ice maker W10583817.

Reset options at a glance

Reset method	What it does	When to use it
Switch OFF then ON	Restarts the ice maker cycle	Ice maker is on but not producing
Unplug for 1 minute	Reboots controls and ice maker circuit	Ice maker seems frozen or unresponsive
Purge water system	Removes air after filter or water work	After filter change or water line service

Why it matters

A proper reset confirms the ice maker is actually enabled and clears minor control glitches. It also helps after a water filter change or a long power outage, when air in the line can delay ice production.

For model-specific control locations and restart notes, use the AFI2538AES owner's manual.

Last updated: February 2026

Amana refrigerators like model AFI2538AES are a good choice when you want dependable, straightforward cooling and solid storage without paying for lots of extra features. They are built to do the basics well; keeping performance strong depends on simple upkeep like cleaning coils and keeping door seals tight (see the AFI2538AES owner's manual).

What “good” usually means for this model type

For a bottom-mount refrigerator, most owners judge “good” by stable temperatures, reasonable operating sound, and low day-to-day hassle.

• Simple controls and fewer complex features can mean fewer complicated repairs over time
• Normal operating sounds (clicking, humming, gurgling) are expected as the compressor cycles
• Efficiency and cooling performance improve when airflow is not blocked and coils are kept clean
• Odor control is manageable with proper cleaning and food storage habits
• Door sealing and leveling matter for consistent temperatures and energy use

How to keep an Amana refrigerator running like a “good” one

The AFI2538AES manual emphasizes habits that directly affect reliability and performance.

• Keep shelves not overcrowded so air circulates
• Avoid loading large amounts of warm food at once
• Do not use foil, wax paper, or paper towels as shelf liners (they restrict airflow)
• Clean door gaskets about every 3 months so doors seal properly
• Clean condenser coils about every 3 months to maintain cooling and efficiency

Quick performance checklist

What you notice	Most common cause	What to do
Food too warm	Dirty coils, frequent door opening, blocked air grille	Clean coils, reduce door-open time, clear vents
Food too cold	Controls set too cold, food near air inlet	Adjust controls, reposition items
Odors	Spills, old food, trapped smells	Deep clean; use the charcoal/newspaper method in the manual

Why it matters

A “good refrigerator” is mostly about consistent temperatures and good airflow. When coils are dirty or doors do not seal, the unit runs longer, temperatures swing more, and noise can seem worse even when nothing is actually broken.

Helpful DIY reading

If your model uses a water filter, following the right replacement steps helps protect water flow and taste: how to replace the water filter in an Amana refrigerator.

Last updated: February 2026

Food freezing in the fresh-food section of your Amana AFI2538AES is usually caused by the temperature controls being set too cold, blocked airflow at the upper left air inlet, or a door that is not sealing and closing properly. Start by adjusting settings and restoring normal airflow per the AFI2538AES owner's manual.

Quick checks that fix most freezing issues

• Raise the refrigerator temperature setting 1 step and wait 24 hours to recheck.
• Make sure food is not pushed against the upper left air inlet (common cause of frozen produce and drinks).
• Avoid overcrowding shelves; poor air circulation can create cold spots.
• Confirm doors close fully and gaskets seal all the way around.
• Turn off Max Cool if it is on; it forces temperatures to the minimum and auto-cancels after about 2 hours.

What to inspect if it keeps happening

Airflow and loading

Cold air enters from the freezer and can freeze items placed directly in the airflow path.

Door sealing and alignment

A door that does not close properly can cause longer run times and uneven temperatures.

Symptom	Most likely cause	What to do first
Items freeze near top/left	Air inlet blowing directly on food	Move items, improve spacing
Random freezing throughout	Controls set too cold or Max Cool used often	Warm setting, stop Max Cool
Freezing plus moisture/frost	Door not sealing	Clean/inspect gasket, check closure

Parts that can be involved (when adjustments do not help)

If temperatures stay erratic after proper loading and control adjustments, a sensing or control issue is possible.

• Refrigerator temperature sensor 12002355 (can misread temperature and overcool)
• High voltage complete board W10890094 (can affect cooling control logic)

Why it matters

Freezing in the refrigerator compartment can ruin food and also points to airflow or control problems that can make the unit run longer than necessary. Correct airflow and settings help stabilize temperatures and improve efficiency.

Last updated: February 2026