Whirlpool DU1100XTPQA dishwasher Parts

On a Whirlpool dishwasher model DU1100XTPQA, the quickest way to clear most error indicators and “reset” the control is to press CANCEL/DRAIN; the dishwasher runs up to a 2-minute drain (if needed) and clears the lights. Then select a cycle and press START/RESUME with the door fully latched (see the DU1100XTPQA owner's manual).

• Press CANCEL/DRAIN once.
• Wait for the drain to finish (up to about 2 minutes).
• If you still see water in the bottom, press CANCEL/DRAIN again to restart draining.
• Close the door firmly until it latches.
• Select your wash cycle and options, then press START/RESUME.

A repeating error plus water left in the bottom usually points to a drain or heater-related issue, not just a one-time glitch.

• Make sure the door is fully closed; if the door is opened mid-cycle, START/RESUME can flash and the cycle will not resume until you latch the door and press START/RESUME.
• Run CANCEL/DRAIN before starting a new cycle (the manual recommends draining before restarting).
• Confirm the dishwasher has power (breaker not tripped).
• If the Clean light is flashing, the manual indicates a malfunction that often involves the heater circuit.

Clearing the indicators with CANCEL/DRAIN resets the cycle logic so you can restart cleanly. If the same error returns after a proper reset and drain, troubleshooting the drain system, heater circuit, or control components prevents repeat stoppages and standing water.

Last updated: February 2026

Whirlpool Corporation manufactures dishwashers sold under several major brands, including Whirlpool, Maytag, KitchenAid, JennAir, and Amana. For your Whirlpool DU1100XTPQA dishwasher, our DU1100XTPQA owner's manual is the best place to confirm features and service information for this specific model.

These are the most common dishwasher brand names produced within the Whirlpool family:

• Whirlpool
• Maytag
• KitchenAid
• JennAir
• Amana

Brand families matter because parts, controls, and wash systems can be shared across multiple model lines, but the exact fit still depends on the model number.

• Always match parts to the full model number (DU1100XTPQA)
• Use the model to confirm electrical and mounting details before ordering
• Compare the symptom to the correct troubleshooting section for your platform
• If you see a fault or blinking pattern, check the right error-code family first

When you are diagnosing issues like not draining, not drying, or no heat, the brand name alone is not enough. The model number (DU1100XTPQA) is what ensures you get the correct parts and the correct repair steps.

If you are troubleshooting a display or blinking-code issue, use our Whirlpool dishwasher error codes reference to narrow the problem to the right system (drain, heating, fill, or control).

Last updated: February 2026

On a Whirlpool dishwasher like model DU1100XTPQA, an F13 code points to a water-heating or water-temperature sensing problem during the cycle. In practice, we treat it as a “water not heating as expected” condition and troubleshoot the heater circuit, wiring, and control.

• Reset the cycle and try again using the steps in the DU1100XTPQA owner's manual.
• Make sure the hot water supply is on and the sink water runs hot before starting.
• Confirm the door is fully latched; a paused or interrupted cycle can create confusing symptoms.
• Run a normal cycle and listen for filling, washing, then a drain; note where it stops.
• If the unit is not drying and the Sanitized light flashes at the end, that supports a heating issue.

If the dishwasher fills and washes but does not heat or dry, these are the most common suspects:

• Heating circuit: dishwasher heating element W10518394
• Temperature/soil sensing: sensor WPW10705575
• Main control (commands heat): dishwasher electronic control WPW10084141

Heating is what boosts wash performance and activates drying. When the dishwasher cannot raise water temperature, cycles can run poorly, leave residue, and trigger sanitation-related indicators.

For model-specific button sequences and indicator behavior, use the DU1100XTPQA owner's manual. For general Whirlpool code patterns and what they mean, we also use the Whirlpool dishwasher error codes guide.

Last updated: February 2026

On a Whirlpool dishwasher, the F9 E1 error means the dishwasher is having a drain problem (it is not pumping water out fast enough or it senses water is still in the tub). On model DU1100XTPQA, start by checking simple drain and power items in the DU1100XTPQA owner's manual.

• Cancel the cycle and let the unit try to drain; then check for standing water in the bottom.
• Make sure the door is fully closed and latched.
• Check the kitchen sink drain for a slow clog (a backed-up sink can block dishwasher draining).
• Inspect the drain hose routing for kinks, crushing, or a low loop that is missing.
• If the dishwasher is dead or acts erratic, check the house breaker or fuse.

Drain errors are usually caused by a restriction in the drain path or a weak pump.

When the dishwasher cannot drain, dirty water can be recirculated, cycles can stop mid-wash, and the unit may protect itself by ending the cycle and displaying F9 E1. Fixing the drain path restores normal wash performance and helps prevent odors.

After clearing the drain issue, a reset can help clear the code and restart normal operation. Use the steps in how to reset a Whirlpool dishwasher.

Last updated: February 2026

If you can’t find a part for your Whirlpool DU1100XTPQA dishwasher, we recommend confirming the full model number and then using the parts diagrams and part lists in the DU1100XTPQA owner's manual; if it still doesn’t show up, contact Sears PartsDirect so a parts specialist can cross-reference the correct replacement.

• Match the model number exactly: DU1100XTPQA (letters and numbers matter).
• Check the model and serial tag on the tub frame (commonly visible when the door is open).
• Search by the part name (example: “drain pump” or “door seal”), not just a number.
• Try alternate terms: “control board” vs. “electronic control”, “circulation pump” vs. “pump motor”.
• Look in the correct section of the diagrams (door, tub, pump and motor, wiring).
• If you have an old part number, ask us to cross-reference it to the current substitute.

These are frequently replaced items for this Whirlpool dishwasher model:

Dishwasher parts are often model-specific; even small design changes can affect fit, wiring connectors, and mounting points. Using the exact DU1100XTPQA model number helps ensure the replacement part fits and works correctly.

Last updated: February 2026

On a Whirlpool DU1100XTPQA dishwasher, error code 11 (often shown as “FA” or 11 flashes on some Whirlpool platforms) points to a problem with the optical water indicator (turbidity) sensor that monitors how clean the wash water is; the dishwasher may extend or repeat rinsing when it reads the water as dirty.

• Cancel the cycle and run a reset sequence from the DU1100XTPQA owner’s manual.
• Turn off power at the breaker for 1 minute, then restore power and try a normal cycle.
• Clean the filter area and sump; heavy soil can keep water cloudy and trigger the sensor.
• Verify the water is hot enough at the sink before starting (run hot water 30 to 60 seconds).
• Use fresh detergent and the correct amount; too much detergent can cause filming and false “dirty water” readings.

If the dishwasher keeps repeating rinses, cleans poorly, or shows the code again after cleaning and resetting, the turbidity sensor circuit is the next place to focus.

Common causes include:

• Sensor lens coated with grease or mineral buildup
• Loose or corroded wiring connection at the sensor
• Failed sensor
• Control not interpreting the sensor signal correctly

The turbidity sensor helps the dishwasher decide whether to advance the cycle or add extra rinsing. When it misreads water clarity, you can get longer cycles, higher water use, and inconsistent cleaning.

For code display patterns and related faults, use our Whirlpool dishwasher error codes guide alongside the DU1100XTPQA owner’s manual.

Last updated: February 2026