Kenmore Elite 79671552610 dryer Parts

To hard reset your Kenmore Elite dryer model 79671552610, unplug the dryer (or switch off the breaker) for 5 minutes, then restore power and start a cycle. This clears many temporary control glitches and restores normal operation.

Hard reset steps (power reset)

• Turn the dryer OFF.
• Unplug the power cord; if it is hardwired, turn OFF the dryer breaker.
• Wait 5 minutes (10 minutes if the control seems unresponsive).
• Restore power.
• Press Power, select a cycle, and press Start.
• If the panel is still acting up, repeat once and then move to the checks below.

If the reset does not fix it

A reset helps when the control board is “stuck”, but it will not correct a door switch issue, airflow restriction, or a failed component.

• No power at all: check the breaker (electric dryers often need a full 240V supply).
• Won’t start: confirm the door fully latches; try a different cycle.
• Stops early or dries poorly: clean the lint screen and verify strong airflow.
• Error code showing: use the troubleshooting chart in the 79671552610 owner's manual.

Quick symptom guide

What you see	What it usually means	What to do next
Display frozen or buttons lag	Control glitch	Do the 5-minute hard reset
Runs but no heat	Heating system or airflow problem	Check venting, then test heat components
Starts then stops	Door/venting/overheat protection	Check door closure and airflow
Code on display	Detected fault	Follow the manual’s code steps

Why it matters

A hard reset is the fastest safe first step for electronic control issues. If the problem returns quickly, it points to an underlying condition (like restricted venting or a failing control) that needs troubleshooting instead of repeated resets.

Last updated: January 2026

On Kenmore Elite dryer model 79671552610, the AF code means the dryer is sensing restricted airflow. In most cases, fixing the venting restriction (lint buildup, crushed duct, blocked exterior hood) clears the code and improves drying performance.

What to check first (fast airflow fixes)

• Clean the lint screen completely; wash it with warm water if you see fabric softener residue.
• Check the lint screen housing for lint buildup below the screen.
• Inspect the vent hose behind the dryer for kinks, crushing, or long runs.
• Make sure the exterior vent hood opens freely and is not blocked by lint, snow, or a bird nest.
• Run a timed dry cycle with the vent disconnected briefly (air should blow strongly); reconnect before regular use.

Why AF happens

AF shows up when the dryer cannot move enough air through the drum and exhaust. Poor airflow makes clothes take longer to dry and can cause overheating, which may trip safety thermostats.

Parts that can contribute to airflow problems

If the vent path is clear but airflow is still weak, these parts can be involved:

• Lint screen or grille not sealing or clogged
• Blower wheel loose, broken, or packed with lint
• Blower housing clogged
• Thermostats reacting to overheating from restricted airflow

Symptom	Most common cause	What to do
AF plus long dry times	Blocked vent duct	Clean/shorten vent run; clear exterior hood
AF plus burning smell	Heavy lint restriction	Stop dryer; clean lint path and venting
AF persists with clear vent	Blower issue	Inspect blower area; replace if damaged

Model-specific help

For cleaning points and access panels on this Kenmore Elite dryer, follow the steps in the 79671552610 owner's manual. If you suspect a damaged blower, the dryer blower wheel 5835EL1002A is the correct blower wheel listed for this model.

Why it matters

Restoring proper airflow helps the dryer heat correctly, dry faster, and reduces strain on components like the motor, belt, and thermostats.

Last updated: January 2026

On Kenmore Elite dryer model 79671552610, the model number is printed on the appliance’s rating label. You’ll typically find that label when you open the dryer door and look around the door opening area, or on the door itself.

Most common places to check

Look for a sticker or metal tag that lists the model and serial number. Check these spots first:

• Door opening (cabinet frame) near the lint screen housing
• Inside the door opening on the front panel
• On the dryer door edge or inner door area
• Back panel of the dryer cabinet (upper area)
• Side panel near the rear edge (less common)

For diagrams and label-location notes specific to this dryer, use the 79671552610 owner’s manual.

What the label looks like (and what to copy)

The rating label usually includes several identifiers. Copy these exactly:

Label item	What it’s used for
Model number (79671552610)	Matching parts and service info
Serial number	Production details, warranty/service reference
Electrical rating	Confirming power requirements

Why it matters

We use the full model number to match the correct Kenmore parts and diagrams for your exact dryer configuration. Even one digit off can point to a different drum, belt routing, or control setup.

Quick tip for parts matching

If you’re ordering common wear items after you find the model number, these are frequently replaced on this style of dryer:

• Drum belt
• Idler pulley
• Drum support roller
• Lint screen

Example part listing for this model: lg dryer drum belt 4400EL2001F.

Last updated: January 2026