Kenmore Elite 79571054010 refrigerator Parts

The Kenmore Elite model 79571054010 has a 30.6 cubic foot total capacity.

We recommend double-checking the capacity using the model and rating information for your exact unit.

• Look for the model and serial label inside the fresh food compartment (often on a side wall)
• Match the model number exactly: 79571054010
• Check the specifications section in the owner's manual
• If you have the original sales paperwork, it often lists total capacity

Knowing the cubic feet helps when you are comparing replacement refrigerators, planning kitchen fit, and choosing compatible storage accessories (bins, drawers, and door components) for your Kenmore Elite bottom-mount refrigerator.

Last updated: February 2026

On Kenmore Elite model 79571054010, the model and serial number are printed on an identification label located on the right-hand side of the refrigerator compartment. Use the label information when ordering parts or checking the specifications in the owner's manual.

• Open the fresh food (refrigerator) door, not the freezer drawer
• Look along the right interior wall of the refrigerator compartment
• Check near the crisper drawer area and side wall surfaces
• Use a flashlight; the label is often small and easy to miss
• Write down both the model number and the serial number

We use the model number to match the correct Kenmore Elite refrigerator parts list for 79571054010, such as the refrigerator door switch 6600JB1010A or the genuine Kenmore refrigerator water filter 9690 AGF80300801. Even small model variations can change which door bins, control boards, or ice maker parts fit.

• Match the full model number exactly: 79571054010
• If a part is tied to the dispenser or ice system, confirm the exact configuration first
• Use the manual diagrams and parts list together to avoid returns

Last updated: February 2026

To adjust door height on your Kenmore Elite refrigerator model 79571054010, use the included wrench to turn the hinge adjustment nut: turn counterclockwise to raise the door or clockwise to lower it. Recheck the door gap and closing after each small adjustment; see the owner's manual.

• Unload heavy items from the door bins to reduce weight while adjusting.
• Open both fresh food doors and compare the top edges and the center gap.
• Use the included wrench to turn the hinge adjustment nut:
  • Counterclockwise: raises the door
  • Clockwise: lowers the door
• Make small changes, then close both doors to confirm the seal and alignment.
• If the doors still do not close easily, adjust the refrigerator tilt using the front leveling legs.

Your refrigerator has two front leveling legs. Turning them changes the cabinet tilt, which affects door alignment.

• Remove the base cover (open the freezer drawer, remove the cover screws).
• Turn the leveling legs:
  • Clockwise: lowers the front (tilts back more)
  • Counterclockwise: raises the front
• Set the front slightly higher than the back so doors close more easily.

Proper door height and leveling help the door gaskets seal evenly. That prevents warm air leaks, reduces frost and moisture, and helps the compressor run less.

Last updated: February 2026

Common problems we see with the Kenmore Elite 79571054010 bottom-mount refrigerator include weak or no cooling, ice maker or dispenser issues, water leaks, and normal-to-loud operating noises. Many of these trace back to airflow (dirty condenser coils or a fan issue), defrost/drain problems, or a control setting such as Demo mode; use the owner's manual for model-specific checks.

• Not cooling or warm temperatures: dirty condenser coils, evaporator fan problems, defrost system trouble, or Demo mode enabled
• Ice maker not making ice: ice compartment door not sealing, ice bin uneven or overfilled, ice maker switched off
• Water leaking or puddles: clogged/iced drain path, loose water line connection, cracked tubing
• Noisy operation: fan airflow noise, defrost sizzling, popping from normal expansion, water running to the drain pan
• Dispenser not working: actuator/switch failure, door switch issue, or ice chute/auger drive problem

1. Confirm cooling is actually enabled: If lights and display work but it will not cool, check for Demo (Demonstration) mode. The manual procedure disables Demo mode by opening a door and pressing Ultra Ice and Refrigerator Temp together for 5 seconds.
2. Clean the condenser coils: Dust buildup reduces cooling and can increase noise and run time.
3. Check door closing and sealing: Doors should close fully; gaskets should be clean and making full contact.
4. Ice maker basics: Keep the ice compartment door closed tightly; level the ice in the bin if it “bridges” and stops production.

Cooling, ice, and leak complaints often share the same root causes: restricted airflow, incorrect settings, or water system restrictions. Addressing the simple items first (Demo mode, coils, doors, ice bin) prevents unnecessary part replacement and food spoilage.

Last updated: February 2026

On Kenmore model 79571054010, the water filter is installed in the filter housing (manifold) inside the fresh food section; you remove the old cartridge and push the new one straight into the manifold until it stops. Use the owner's manual for the exact filter access location and steps for your cabinet layout.

Most Kenmore bottom-mount designs place the filter in one of these spots:

• Upper right corner inside the refrigerator compartment
• Upper left corner inside the refrigerator compartment
• Along the back wall inside the refrigerator compartment
• At the base grille area (less common on this style)

If you do not see a filter head inside the refrigerator section, check the base cover area and confirm the location in the owner's manual.

When installing the new cartridge, the manual guidance is to align the filter tabs horizontally, then push the filter into the manifold hole until it stops.

Best practices during install:

• Remove the protective cover from the O-rings before inserting
• Push firmly and evenly; do not twist unless your housing design requires it
• Check for leaks at the filter head after the first few dispenses
• Flush water through the dispenser to clear air and carbon fines

If you are not using a filter temporarily, install a bypass plug so the water circuit stays sealed.

A correctly installed filter (or bypass plug) prevents leaks, keeps water flowing to the dispenser and ice maker, and helps reduce taste and odor issues caused by minerals in the water supply.

Last updated: February 2026