Maytag MVWB855DC1 washer Parts

For the Maytag MVWB855DC1 washer, the most common issues we see are drain and spin problems (won’t drain, won’t spin, stops mid-cycle), vibration from unbalanced loads, and normal-to-concerning noises caused by items in pockets or the drain system. Use the MVWB855DC1 owner's manual for model-specific troubleshooting steps.

• Won’t drain or leaves water in the tub: drain path restriction, pump issue, or a kinked drain hose
• Won’t spin or stops during spin: unbalanced load, lid not locking, or drive system problem
• Shakes, bangs, or “walks”: load not distributed evenly, washer not level
• Clicking or metallic noise: coins or small items caught between basket and tub, or in the drain system
• Humming with gurgling: often normal while the washer is pumping out water

1. Redistribute the load in loose heaps evenly around the washplate; avoid washing single heavy items.
2. Confirm the washer is level; a firm floor and proper leveling reduce vibration.
3. Check pockets for coins, screws, and other small items before washing.
4. Inspect the drain hose for kinks or crushing; make sure it is routed correctly.
5. Do not add extra water to “cover” the load; this HE washer is designed for low-water operation.

If the quick checks do not fix it, these model-matched parts are frequent solutions:

You can order replacement parts from the parts list for this Maytag MVWB855DC1 washer, or search by model number on Sears PartsDirect.

Drain and spin issues can leave clothes soaking wet and can trigger repeated cycle interruptions. Unbalanced loads and poor leveling increase vibration, which accelerates wear on suspension and drive components over time.

Last updated: February 2026

A Maytag washer typically lasts 10 to 13 years. For your Maytag MVWB855DC1, lifespan depends most on weekly load volume, how often it is overloaded, and routine care (especially keeping the tub and drain system clean). See the MVWB855DC1 owner's manual for the maintenance schedule and operating tips.

Most residential washers land in the same general range, but these factors move the needle the most:

• Loads per week: more cycles equals more wear on the drive system and suspension
• Overloading: strains the basket, drive, and dampers; increases out-of-balance events
• Detergent use: too much HE detergent can cause residue and odor issues
• Water quality: hard water can increase buildup and reduce cleaning performance
• Drain health: slow draining makes the pump work harder and can leave standing water

A washer rarely fails all at once; it usually shows repeat symptoms tied to a few systems.

When performance problems start, replacing the right wear part often restores normal operation and helps you get more years out of the washer:

• If the washer won’t drain or drains slowly, check the washer drain pump W10876600 and the washer drain hose W11244231
• If the washer won’t fill or fills inconsistently, the washer water inlet valve W11165546 is a common fix after confirming good water pressure
• If the washer won’t lock or won’t start, the washer lid lock assembly W10810403 is a frequent culprit
• If the washer shakes or bangs often, worn suspension is likely; consider the damper assembly W11130356

Knowing the 10 to 13 year lifespan range helps you decide whether to repair or refresh key components. On a washer like the MVWB855DC1, targeted repairs (drain, fill, lid lock, suspension) often restore reliability without replacing the entire unit.

You can order MVWB855DC1 replacement parts from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

The Maytag MVWB855DC1 top-load washer has a 5.3 cu. ft. capacity, which is considered a large-capacity tub for handling bulky loads like bedding and towels. For cycle-by-cycle loading guidance and options that affect how the washer senses and fills, use the MVWB855DC1 owner's manual.

Capacity is the tub volume, not a guaranteed “one-size” load limit. Your MVWB855DC1 uses load sensing and low-water washing, so performance depends on how freely items can move.

• Load items in loose heaps evenly around the washplate
• Mix different sized items to reduce tangling
• Avoid tightly packing; it can lead to poor cleaning and off-balance spinning
• Use HE detergent only to prevent excess suds and long cycle times
• For waterproof or water-resistant items, load evenly and use the recommended cycle guidance

When the tub is overloaded or items cannot move freely, the washer can struggle to balance and spin, leaving clothes wetter than normal. Correct loading also helps the sensing system estimate the load accurately and add the right amount of water.

Capacity is fixed, but these parts can affect how well the washer fills, drains, and spins under heavier loads:

• Washer water inlet valve W11165546 (filling issues)
• Washer drain pump W10876600 (draining and spin performance)
• Damper assembly W11130356 (vibration and off-balance control)

If you are ordering replacement parts for MVWB855DC1, use the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026

Yes. On the Maytag MVWB855DC1 washer, a clogged drain path can trigger an F9E1 long-drain condition because the washer cannot pump water out within the required time. Clearing restrictions in the drain hose, standpipe, or drain pump area typically restores normal draining.

• Unplug the washer before inspecting hoses or the pump area.
• Check the household standpipe or laundry tub for a slow or backing-up drain.
• Verify the drain hose is not kinked, crushed, or pinched behind the washer.
• Make sure the drain hose is secured correctly and not sealed with tape.
• Confirm the drain hose is not pushed too far into the standpipe (too deep can restrict draining).

A clog can be in the home drain, the washer drain hose, or inside the washer at the pump.

If the drain path and household plumbing are clear and the washer still drains slowly, the drain pump can be obstructed or worn.

• If the pump runs but water barely moves, inspect the pump inlet and outlet for debris.
• If draining is inconsistent across loads, check for small items repeatedly entering the pump area.
• If the pump will not move water after clearing debris, replacement is the next step.

For a model-matched replacement, use the parts list for MVWB855DC1 and look up the washer drain pump W10876600.

Long-drain conditions stop the cycle to prevent water backup and protect the washer during drain and spin. Fixing the restriction also helps prevent overly wet loads and repeat drain or spin interruptions.

• Use the MVWB855DC1 owner’s manual for drain hose installation guidance and troubleshooting steps.
• If your display shows additional codes, use the Maytag bravos vmw top load washer error codes guide to narrow the troubleshooting path.

You can order MVWB855DC1 replacement parts from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026