Kenmore 10650042717 refrigerator Parts

For Kenmore model 10650042717 (Coldspot side-by-side), the cabinet is typically about 66 3/4 in. tall (with hinge) and about 32 1/8 in. deep without the handle; plan on roughly 49 7/8 in. of clearance for maximum depth with the doors open. Confirm your exact configuration in the 10650042717 owner's manual.

Key dimensions to plan for

• Height (with hinge): 66 3/4 in.
• Depth (without handle): 32 1/8 in.
• Depth (with handle): 33 7/9 in.
• Max depth with doors open: 49 7/8 in.

Installation clearance that matters

Even when the refrigerator fits the cutout, it still needs airflow and door-swing space.

• Allow 1/2 in. clearance on each side and at the top
• Allow 2 in. clearance behind the refrigerator
• If you have an ice maker, leave extra room for the water line connection
• If installed next to a wall, leave enough space for the doors to swing fully

Quick planning table

Measurement	What it affects	What to do
Height with hinge	Overhead cabinet clearance	Measure floor to cabinet bottom
Depth without handle	Fit into the opening	Measure wall to front edge of cabinet
Depth with handle	Walkway clearance	Check aisle space in front
Doors-open depth	Drawer and shelf access	Ensure you can fully open doors

Why it matters

Correct sizing prevents poor ventilation (warm temps, higher energy use) and avoids door interference that can damage hinges, bins, and gaskets over time.

Last updated: February 2026

For Kenmore refrigerator model 10650042717, the model number is the full identifier you use to match the correct parts and instructions. We recommend copying it exactly as shown on the appliance data label, then confirming it against the 10650042717 owner's manual.

Where to find the model number label

On most Kenmore side-by-side refrigerators, the model number label is typically located in one of these spots:

• Inside the fresh food (refrigerator) compartment on a side wall
• Inside the freezer compartment on a side wall
• On the inside wall behind the lower crisper drawer area
• Behind the toe grille (kick plate) at the bottom front
• Along the door frame area (visible when the door is open)

How to read it correctly (so parts match)

Kenmore model numbers must be read as one continuous string. For this unit, 10650042717 is the model number you should use when ordering parts like a door bin or evaporator fan motor.

• Write down every digit in order (do not add spaces)
• Do not use only the “106” prefix; that is a model series, not the full model
• If the label includes additional characters (such as a revision code), record those too
• Use the model number when searching diagrams and parts lists
• Match the model number before buying electrical parts (fan motor, capacitor, user interface)

Quick check: model number vs. part numbers

What you’re looking at	Example	What it’s used for
Model number	10650042717	Identifies the exact refrigerator version
Part ID	WP2315549	Identifies a specific replacement part listing
Part number	W11036340	Manufacturer number used across brands/models

Why it matters

Kenmore 106-series refrigerators often share similar styling, but internal components can differ by revision. Using the exact model number helps ensure the right fit for items like the refrigerator door bin W11174793 and prevents ordering the wrong electrical or water system parts.

Last updated: February 2026

To replace the ice maker in your Kenmore 10650042717 side-by-side refrigerator, we disconnect power, remove the ice bin and mounting hardware, swap in the new ice maker, then restore power and water and turn ice production back on. Follow the safety and access steps in the 10650042717 owner's manual.

Safety first (do this before touching anything)

• Unplug the refrigerator or disconnect power at the breaker.
• Turn the ice maker off (wire shutoff arm up, or switch to Off, depending on your style).
• If you will disconnect any water line, shut off the household water supply.
• Use gloves; sheet metal edges inside the freezer can be sharp.
• Reinstall all covers and panels before operating.

Basic replacement steps (typical side-by-side procedure)

1. Remove the ice storage bin
   • Open the ice maker door.
   • Turn the ice maker off.
   • Lift the front of the bin and pull it out.
2. Remove the ice maker assembly
   • Take off the ice maker cover (if equipped).
   • Remove mounting screws and support the ice maker as the last screw comes out.
   • Disconnect the wiring harness plug.
3. Install the new ice maker
   • Connect the wiring harness firmly.
   • Hang the ice maker on the mounting points and tighten screws.
   • Reinstall the cover and slide the bin fully back in (the dispenser will not work if the bin is not seated).
4. Turn everything back on
   • Restore power.
   • Turn the ice maker on (wire shutoff arm down, or switch to On).

Ice maker on/off styles (what you should see)

Ice maker style	How to turn it ON	How to turn it OFF
Wire shutoff arm	Arm down	Arm up until it clicks
On/Off switch	Switch to On (right)	Switch to Off (left)

After installation: what to expect

• First batch of ice commonly takes 12 to 24 hours.
• Discard the first full bin of ice if the unit has been off or water lines were opened.
• If ice is slow, confirm the water supply valve is fully open and the freezer is set cold enough.

Why it matters

A correctly mounted ice maker and fully seated ice bin prevent dispenser problems and help the ice maker shut off properly when the bin is full, reducing jams and overflow.

Last updated: February 2026

For Kenmore model 10650042717 side-by-side refrigerators, the most common problems we see are cooling complaints, water leaks, ice maker or dispenser issues, and unusual noises. Many of these come down to airflow restrictions (blocked vents or dirty coils), door sealing problems, or a failing fan or dispenser component; the 10650042717 owner's manual troubleshooting section is the best starting point.

Most common symptoms and what usually causes them

• Not cooling or weak cooling: blocked air vents, dirty condenser coils, evaporator fan issue, or defrost-related frost buildup
• Runs too much: frequent door openings, warm room, large food load, or airflow problems (some longer run time is normal with efficient compressors)
• Water leaking or puddles: clogged defrost drain, loose water line connection, cracked tubing
• Ice maker not making ice: water supply issue, frozen fill tube, ice maker assembly problem
• Dispenser problems (no ice, no water, weak dispense): frozen reservoir/tube, filter housing issue, dispenser motor issue
• Noisy operation: fan blade rubbing ice, worn fan motor, items vibrating against the cabinet

Quick checks we recommend first (fast, no parts)

• Confirm doors close fully and seals contact the cabinet all the way around.
• Make sure air vents are not blocked by food packages (the manual notes blocked vents can cause temperature issues).
• After a new install or power outage, allow 24 hours for temperatures to stabilize.
• Verify the outlet has power and the cord is plugged into a grounded 3-prong outlet.
• Listen for where the noise comes from (freezer rear panel often points to evaporator fan area).

Parts that commonly solve these problems on this model

Problem area	Common fix	Example part for 10650042717
Warm temps, noise from freezer	Replace evaporator fan motor or blade	Refrigerator evaporator fan motor WP2315549, refrigerator evaporator fan blade WP2169142
Dispenser not dispensing ice well	Replace dispenser drive motor	Motor, dispenser W11671282
Leaks or weak water dispense	Inspect/replace water tubing	Refrigerator water tube W10823511

Why it matters

Cooling, ice, and leak symptoms often share the same root causes: restricted airflow, moisture freezing where it should not, or worn moving parts. Catching these early helps prevent food spoilage, ice buildup, and water damage.

Last updated: February 2026

Your Kenmore side-by-side refrigerator model 10650042717 has a total capacity of about 21.9 cubic feet. This is the overall storage volume for both the fresh food and freezer compartments combined; exact usable space varies with shelves, bins, and the ice system.

How to confirm capacity for your exact configuration

We recommend checking the model’s documentation because capacity is sometimes listed by model series and can vary slightly by option package.

• Look for “capacity,” “total volume,” or “specifications” in the 10650042717 owner's manual
• Check the model series listing (the manual covers 106.5004* models)
• Compare your door bin and shelf layout to the diagrams in the manual
• If you use an ice maker and ice container, remember they reduce usable freezer space

What “21.9 cu. ft.” means in real use

“Cubic feet” is the internal volume measurement, not the amount of food you can comfortably store. Items like the ice bucket, crisper pans, and door bins change how that space is divided.

Measurement	What it represents	What can change it
Total capacity (cu. ft.)	Combined fresh food + freezer volume	Model variant, insulation, liner design
Usable space	Practical storage room	Shelves, bins, ice container, air channels
Storage layout	How space is organized	Door bins, crisper pans, shelf positions

Why it matters

Capacity helps when you are comparing refrigerators, planning kitchen fit, or deciding whether storage accessories (like a larger bin) make sense for your household. It also sets expectations for how much freezer space you will have once the ice system is installed.

Last updated: February 2026

Most Kenmore refrigerators average 10 to 15 years of service life. For a Kenmore side-by-side like model 10650042717, lifespan depends most on basic care (airflow, clean coils, good door sealing) and fixing cooling or ice-maker issues early; see the 10650042717 owner's manual for model-specific care and troubleshooting.

Typical lifespan ranges (what we see most often)

• 10 to 15 years: common for many modern refrigerators
• 15 to 20 years: achievable with consistent maintenance and timely repairs
• 20+ years: possible, usually when the sealed system stays healthy and wear items are replaced as needed

What affects lifespan most	What to do	What it prevents
Dirty condenser coils	Vacuum and brush coils regularly	Compressor overheating, poor cooling
Weak door seal	Inspect for gaps, clean gasket, replace if torn	Frost buildup, long run times
Poor airflow inside	Do not block vents, avoid overpacking	Warm spots, icing
Water/ice issues	Replace filters on schedule, fix leaks quickly	Valve clogs, dispenser failures

Maintenance that adds years (high impact)

• Clean condenser coils and keep the grille area clear for airflow.
• Keep doors closing tightly; wipe the gasket and check for warping.
• Set stable temps (typically 37°F fresh food, 0°F freezer) and avoid frequent adjustments.
• Keep the ice bin and chute clear to prevent jams and motor strain.
• Address fan noise or warming quickly; evaporator airflow problems can snowball.

Parts that commonly extend usable life

If performance is slipping, replacing a worn part is often more cost-effective than living with poor cooling.

• Refrigerator door switch W11396033: helps interior lights and some fan logic work correctly when doors open and close.
• Refrigerator evaporator fan motor WP2315549: restores airflow through the evaporator for steady temperatures.
• Refrigerator capacitor WPW10662129: supports compressor starting and running on many designs.

Why it matters

A refrigerator that runs longer than it should (from dirty coils, air leaks, or weak airflow) uses more energy and puts extra stress on the compressor. Preventive care and early part replacement are the biggest drivers of reaching the upper end of the lifespan range.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10650042717, the model number is printed on the appliance identification label. We typically see this label inside the fresh food (refrigerator) compartment, along the side wall or near the top opening where the door seals.

Where to look first (fastest checks)

• Open the refrigerator (fresh food) door and scan the left and right interior walls
• Check near the ceiling of the fresh food compartment, just inside the door opening
• Look behind or beside the crisper drawers on the side wall
• Check the door frame area where the gasket meets the cabinet
• If you have a dispenser model, also check around the water filter door area

What the label looks like

The ID label is usually a white or silver sticker and includes:

• Model number (for example, 10650042717)
• Serial number (a longer code used to identify production details)
• Electrical ratings (volts/amps)

For the exact label location and diagrams for your series, use the 10650042717 owner's manual.

Model number vs. serial number (quick comparison)

Item	What it’s used for	Example format
Model number	Matching parts and diagrams	10650042717
Serial number	Dating/production identification	Letters plus numbers

Why it matters

Using the correct model number ensures we match the right Kenmore parts (like a door switch, evaporator fan motor, or water filter housing) because small design changes can affect fit and wiring.

Last updated: February 2026

Water leaking from the bottom of your Kenmore 10650042717 side-by-side refrigerator usually comes from defrost water not draining into the drain pan, or from a small water supply or dispenser drip that runs down and collects underneath. Use the checks in the 10650042717 owner's manual to narrow it down fast.

Quick checks (most common causes)

• Clogged or frozen defrost drain; meltwater overflows to the floor
• Drain pan shifted, dirty, or cracked
• Water line connection seepage at the back of the refrigerator
• Dispenser after-drip (a few drops are normal)
• Ice chute has ice shavings that melt and drip

Step-by-step: isolate the leak source

1. Locate the puddle
   • Front center under doors: usually defrost drain or drain pan.
   • Back bottom: usually water supply line or fittings.
2. Check for dispenser after-drip
   • Hold the glass under the dispenser 2 to 3 seconds after releasing the lever.
3. If the filter was just replaced or water was just connected
   • Flush the water system to purge air (air can cause dripping).
4. Inspect rear water connections
   • Confirm fittings are snug; re-seat tubing if you see moisture.

What to do based on symptoms

Symptom	Most likely cause	What we recommend
Puddle shows up after defrosting	Defrost drain clogged/frozen	Thaw ice, then clear the drain path with warm water
Water at back of unit	Loose water line connection	Tighten and re-seat connections; check tubing for cracks
Drips at dispenser	Air in line or normal after-drip	Flush system; use the 2 to 3 second hold-under-glass habit
Water near ice chute	Ice shavings melting	Clear ice pieces/shavings from chute and bin

Why it matters

Bottom leaks can damage flooring and often signal restricted drainage that can lead to ice buildup in the freezer. Fixing the drain path or water connections stops repeat puddles and helps the refrigerator run normally.

Last updated: February 2026