Whirlpool WGE745C0FS00 electric double oven range Parts

On a Whirlpool WGE745C0FS00 electric double oven range, a bad oven control board commonly shows up as a dead or glitchy display, buttons that do not respond, or oven functions that start, stop, or heat incorrectly. Confirm basic power and wiring checks before replacing electronics using the WGE745C0FS00 installation guide.

Common symptoms you may notice

• Display is blank, flickers, or shows random characters
• Touchpad or keys do not beep or accept selections
• Oven will not bake or broil, or heats erratically
• Temperature is far off from the set point (overheats or underheats)
• Oven turns on by itself, shuts off mid-cycle, or will not shut off
• Error codes appear repeatedly after a power reset

Quick checks before blaming the control board

These checks help rule out power supply and connection issues that can mimic a failed board.

• Verify the range has correct household power (a tripped breaker can leave the control lit but prevent heating)
• Power reset: turn the breaker off for 1 minute, then back on
• Inspect for loose or heat-damaged connectors at the control area
• If the oven will not heat, consider a failed heating circuit component such as the control W10877730 or a heating element (if symptoms match)
• If the cooktop works but both ovens act up, the control system is a stronger suspect than a single element

Symptom-to-likely-cause guide

Symptom	More likely cause	Less likely cause
Blank display, no response	Control board, power supply issue	Door switch, element
Oven heats but temp is wrong	Sensor or control board	Element
Random beeping or self-starting	Control board or keypad/touch panel	Wiring harness
One function fails (bake only)	Element or relay on board	User settings

Why it matters

The oven control board is the “traffic controller” for bake, broil, timing, and temperature regulation. Misdiagnosing it can lead to replacing expensive parts when the real issue is power, wiring, or a heating component.

Last updated: January 2026

Uneven baking or an oven temperature that runs too hot or too cool is one of the most common issues we see on the Whirlpool WGE745C0FS00 electric double oven range. It’s usually tied to a heating circuit problem (bake or broil), heat loss at the door, or an oven control issue (see the WGE745C0FS00 use & care manual).

Most common symptoms

• Food browns on one side but not the other
• Preheat takes much longer than normal
• Temperature seems off compared to the set point
• One oven cavity performs differently than the other
• Baking results vary from rack to rack

Likely causes on this model

These are common culprits for WGE745C0FS00 when heating is uneven or inaccurate:

• Weak or failed bake element: can cause low heat or uneven heat (example: range bake element W11662148)
• Broil circuit not assisting properly: can affect preheat and temperature cycling (example: range broil element, lower WPW10611615)
• Oven control problem: may not regulate power correctly (example: control W10877730)
• Door heat loss: a worn gasket can leak heat and skew baking results (example: oven door gasket WPW10269069)

Quick checks we recommend before replacing parts

• Verify you are using the correct bake mode for the upper vs. lower oven
• Fully preheat, then confirm temperature with an oven thermometer
• Look for visible damage on the bake element (blisters, cracks, burn marks)
• Check the door seal for gaps, tears, or loose sections
• If the oven is completely dead, check the home breaker and power supply

What to check first (simple guide)

Symptom	Check first	Why it matters
Won’t heat at all	Bake element	Most common no-heat failure point
Bakes unevenly	Bake element, door gasket	Heat output and heat loss cause hot/cool spots
Preheats slowly	Broil circuit, bake element	Preheat often uses multiple heat sources
Temperature swings widely	Control	Controls cycling and temperature regulation

Why it matters

Stable oven temperature is what prevents undercooked centers, burnt edges, and long cook times. Fixing a weak heating component early can also help prevent overheating at terminals and wiring.

Last updated: January 2026

A Whirlpool electric range like model WGE745C0FS00 typically lasts 10 to 15 years with normal household use. With consistent cleaning, proper electrical installation, and timely replacement of wear parts, many ranges reach the upper end of that range.

What affects lifespan most on WGE745C0FS00

• High-heat cycles (especially frequent self-clean use) accelerate wear on door gaskets, locks, and electronics.
• Power quality (surges, loose connections) can shorten the life of control boards and touch panels.
• Heavy daily cooking increases wear on bake/broil elements and surface elements.
• Ventilation and spills: grease and boilovers can damage switches and wiring.
• Door seal condition: heat loss makes the oven work harder and can cause uneven baking.

Practical ways we extend range life

• Keep the oven cavity and door seal clean; follow cleaning guidance in the WGE745C0FS00 use & care manual.
• Avoid running self-clean back-to-back; let the range cool fully between cycles.
• Use cookware that matches burner size to reduce overheating of radiant elements.
• If a burner cycles erratically or will not regulate heat, test and replace the control switch (for example, range infinite switch W10917724) before it overheats wiring.
• Replace a worn door seal to maintain temperature and protect components (for example, oven door gasket WPW10269069).

Common “end of life” symptoms vs repairable issues

Symptom	Often repairable?	Typical parts involved
Oven not heating or slow preheat	Yes	Bake element, wiring
Burner stuck on high or won’t heat	Yes	Infinite switch, surface element
Door won’t close/seal well	Yes	Door hinge, door gasket
Random resets or dead display	Sometimes	Control board, harness

Why it matters

Knowing the typical 10 to 15 year lifespan helps us decide when a repair (like an element, switch, or gasket) is a smart investment versus when multiple major electronic failures may make replacement more practical.

Last updated: January 2026

The Whirlpool WGE745C0FS00 is a freestanding electric double oven range in the WGE745C0FS family. Based on the installation specifications for this exact model, it fits a 30-inch opening and has an overall width of about 29 15/16 inches (76.0 cm). See the WGE745C0FS00 installation guide for the full dimension and clearance details.

Key specs we can confirm for WGE745C0FS00

From the installation requirements and dimension chart, we can confirm these model-specific details:

• 30-inch minimum cabinet opening width (U.S.A.)
• Overall width: 29 15/16 inches (76.0 cm)
• Cooktop height (minimum): 35 3/4 inches (90.8 cm) with leveling legs fully in
• Overall height (minimum): 47 1/8 inches (119.7 cm) with leveling legs fully in
• Depth with handle: 28 1/2 inches (72.4 cm)

What “range” can mean (and what varies)

Customers use “range” in a few different ways. Here is how we interpret it for this model:

If you mean…	For WGE745C0FS00, we can…	Where to verify
Physical size (width/height/depth)	Confirm key dimensions	WGE745C0FS00 installation guide
Electrical requirements (amps/cord type)	Confirm general connection options and ratings guidance	WGE745C0FS00 installation guide
Cooking features (elements, wattage, oven capacity)	Not identify exact feature set from the installation text provided	WGE745C0FS00 owner’s manual

Why it matters

Getting the correct “range” details for Whirlpool WGE745C0FS00 helps you avoid fit problems (cabinet opening, depth to the wall, handle clearance) and safety issues (proper electrical connection and anti-tip bracket installation).

Last updated: January 2026

For your Whirlpool electric double oven range model WGE745C0FS00, the most reliable way to identify the correct part number is to use the model and serial information from the appliance rating plate, then match that model to the parts list and diagrams in the WGE745C0FS00 installation guide.

Where to look on model WGE745C0FS00

On this model, the model/serial/rating plate is located behind the control panel. That plate is what you use to confirm the exact model number before choosing a replacement part.

• Look behind the control panel area for the rating plate
• Write down the model number and serial number exactly as shown
• Use the confirmed model number to select the correct diagram and part
• If the plate is hard to read, take a clear photo and zoom in
• Match the part by name and location in the diagram, then confirm the part number

How to match the right part once you have the model number

After you confirm WGE745C0FS00, choose the part by function (bake, broil, surface element, switch, handle) and then verify the part number against the listing.

Common examples for this model include:

What you are replacing	What to match	Example part listing name
Oven not heating (bake)	Bake element shape and mounting	Range bake element
Burner not regulating heat	Infinite switch type/shaft	Range infinite switch
Cooktop burner not heating	Radiant element size/type	Range radiant surface element

Why it matters

Whirlpool ranges often have similar-looking parts across close model numbers, but small design changes can affect fit, wiring, and mounting. Confirming the rating plate info first helps ensure the replacement part is compatible and avoids returns.

Last updated: January 2026