Whirlpool WED5100HW3 laundry, residential, electric dryer Parts

A blown thermal fuse on your Whirlpool WED5100HW3 often shows up as a dryer that will not start, or a dryer that runs but has no heat. We confirm it by testing the fuse for continuity with a multimeter; a blown fuse reads open (no continuity) and must be replaced.

• Dryer will not start (motor will not run)
• Dryer runs but does not heat (clothes stay damp)
• Cycle ends with poor drying because airflow is restricted
• You recently had a clogged vent, crushed duct, or heavy lint buildup

1. Unplug the dryer (electric shock hazard).
2. Access the thermal fuse (commonly on the blower housing or exhaust path on many Whirlpool electric dryers).
3. Pull the wire connectors off the fuse terminals.
4. Set a multimeter to continuity or ohms.
5. Touch one probe to each terminal.

A thermal fuse is a one-time safety device; once it opens, it does not reset.

If your WED5100HW3 needs a fuse, match by model and symptom. For this model page, common safety parts include the thermal fuse W10909685 and the Whirlpool dryer thermal cut-off fuse kit 279973.

A thermal fuse usually blows because the dryer overheated from restricted airflow. Replacing the fuse without fixing the venting often leads to another failure and longer dry times.

• Clean the lint screen and confirm it is not coated with fabric softener residue
• Inspect the vent hose for kinks, crushing, or long runs
• Clean lint from the exhaust duct and outside vent hood
• Make sure the blower wheel is moving air (a loose wheel can reduce airflow)

Last updated: February 2026

Common Whirlpool dryer problems on model WED5100HW3 fall into a few buckets: it will not start, it runs but will not heat, it tumbles but dries slowly, or it makes squealing or thumping noises. Most fixes come down to power supply, airflow, or a worn moving part like a roller or idler.

• Dryer will not start: tripped breaker, bad door switch, failed thermal fuse, or control issue
• No heat or weak heat: heating circuit problem, failed heater, or a safety device opened from overheating
• Long dry times: restricted venting, clogged lint path, weak airflow, or moisture sensing issues
• Loud squeal or rumble: worn drum support rollers or idler pulley
• Thumping: flat-spotted rollers, drum issue, or something caught in the blower housing

• Confirm 240V power at the outlet (electric dryers can run on 120V but not heat on 240V issues).
• Clean the lint screen and inspect the lint duct path.
• Check the vent run for kinks, crushed flex duct, or heavy lint buildup.
• Try a timed dry cycle to separate “sensor” issues from “heat/airflow” issues.
• If the dryer overheated recently, inspect safety fuses before replacing other parts.

A dryer that is not heating or is taking too long to dry is often an airflow problem first; restricted venting can also overheat the dryer and open a thermal fuse. Noisy operation is usually a wear item issue (rollers, idler) that is best handled early to prevent belt damage.

For electrical testing, we use a meter to confirm whether a fuse is open or a heater is failed; our guide how to tell if a fuse is blown helps you verify the most common “no start” and “no heat” causes safely.

Last updated: February 2026

For a Whirlpool electric dryer like model WED5100HW3, the model number is printed on the appliance’s rating label. We typically see this label on the door opening area or on the dryer frame just inside the door.

Check these common spots first:

• Open the dryer door and look along the door opening (front panel rim)
• Check the dryer frame just inside the door (often on the right or left side)
• Look behind the door on the cabinet face near the latch area
• If your dryer has a lower access panel, check the inside edge of the front panel

To make sure you get the right diagrams and replacement parts for your dryer, record:

• Model number (example: WED5100HW3)
• Serial number (helps confirm production series)
• Any suffixes or revision codes printed with the model

Whirlpool often updates components during production runs; using the exact model number helps ensure parts like a thermal fuse, heater, or drum support roller match your WED5100HW3 configuration.

Use these options:

• Check your purchase paperwork or delivery receipt for the model number
• Look for a duplicate label on the cabinet (some units have more than one)
• If you are replacing a common wear item, match by model before ordering parts such as the dryer drum support roller WPW10314173

Last updated: March 2026