Craftsman 358356280 chainsaw Parts

On the Craftsman chainsaw model 358356280, the model number is typically found under the handle and is also listed on the starting instructions decal. Use that exact model number when ordering parts or requesting service; it helps ensure correct fit and compatibility.

Check these common locations first (they are the most reliable spots on this model family):

• Under the rear handle (often near the serial number)
• On the starting instructions decal (the manual notes the model and serial numbers are located there)
• On an ID label/tag on the housing near the handle area
• Near the rear handle and fuel tank area where labels are less exposed to heat

For diagrams and label references, use the 358356280 owner's manual.

Use this list to confirm you are reading the correct information:

• Write down the full model number exactly as shown (for this page: 358356280)
• Record the serial number if it is present
• If the decal is dirty, wipe it with a damp cloth and mild soap; avoid solvents that can erase printing
• If the label is scratched, try a flashlight at an angle to make embossed or faded text easier to see

Chainsaw parts like the bar, chain, fuel line, and starter components can vary by production run. Using the correct model number helps us match the right diagrams and avoid ordering a part that looks similar but does not fit.

Last updated: January 2026

On the Craftsman chainsaw model 358356280, the serial number is printed on the starting instructions decal on the saw. Use that serial number (and the model number) when ordering parts, checking compatibility, or looking up the correct operator information in the 358356280 owner's manual.

Look for a decal (label) that includes the starting steps; it also lists the model and serial number.

• Check the starting instructions decal on the saw body
• Wipe off oil and sawdust so the numbers are readable
• Use a flashlight; stamped or printed characters can be faint
• Record the serial number exactly as shown (include any letters)
• Take a photo for your records before the label wears

Having the right ID info prevents ordering the wrong bar, chain, or fuel system parts.

On many gas chainsaws, the serial number may also be stamped into the engine housing or crankcase area near the muffler. If you still cannot locate it, use the model number 358356280 to start your parts lookup and match by diagrams and specifications in the manual.

The serial number can help distinguish between close variants of the same Craftsman chainsaw family, which is important when selecting items like a guide bar, saw chain, fuel line routing, or starter components.

Last updated: January 2026

On a chainsaw chain, S62 is an Oregon chain model code that identifies a specific chain size and configuration. For a Craftsman 358356280 chainsaw, you still must match the chain to the bar and saw specs (pitch, gauge, and drive link count) listed in the 358356280 owner's manual.

S62 commonly refers to a chain that fits many homeowner saws using these specs:

• Pitch: 3/8 in (low profile)
• Gauge: .050 in (1.3 mm)
• Drive links: 62
• Typical bar length: 18 in (varies by bar and sprocket setup)

If your bar is 18 inches but your drive link count is different, an S62 chain will not tension correctly.

Use the bar and chain “Specifications” information in the manual and compare it to what is stamped on your guide bar.

• Look for pitch and gauge markings on the bar (often near the mounting slot)
• Count drive links on your old chain (or read the number on the package)
• Confirm you are using a reduced-kickback guide bar and low-kickback chain as specified for this model
• Inspect the drive sprocket for wear; a worn sprocket can accelerate chain wear and affect fit

If the chain keeps loosening, binds, or wears unevenly, check these common wear items:

• Drum sprocket 530048084 (worn teeth can cause poor chain engagement)
• Guide bar condition (rail wear, burrs, plugged oil hole)
• Chain tensioner parts (adjuster pin and hardware)
• Proper bar oiling (a dry bar overheats and stretches the chain)

Using the correct pitch, gauge, and drive link count helps the chain seat properly on the bar and sprocket. On the Craftsman 358356280, the manual also emphasizes using the specified reduced-kickback bar and low-kickback chain to reduce kickback risk.

Last updated: January 2026

The model number for this Craftsman gas chainsaw is 358356280. You’ll typically find the model number on the saw’s ID label, and it’s also the number you should use to match the correct parts list and operator information in the 358356280 owner's manual.

On most Craftsman gas chainsaws, the model number is printed on an ID tag or label attached to the housing.

• Check the rear handle area near the fuel tank
• Look around the starter housing (recoil cover)
• Inspect the crankcase area near the bar mount
• Wipe off oil and sawdust; labels can be hard to read when dirty

Craftsman chainsaws often look similar across different versions, but parts can vary by model and bar length. The manual’s parts list for MODEL 358.356280 helps ensure you get the right items for fuel, ignition, and cutting components.

If you’re shopping parts for Craftsman 358356280, these are common items customers replace during tune-ups and repairs:

• Line kit 530069216 (fuel line kit) for cracked or leaking fuel lines
• Check valve 530026119 for fuel system venting and flow issues
• Drum sprocket 530048084 if the chain drive slips or the sprocket teeth are worn

Using the exact model number prevents mismatched parts (especially bar/chain and fuel system components) and keeps troubleshooting accurate when the chainsaw won’t start, runs rough, or leaks gas.

Last updated: January 2026