Kenmore Elite 79574073810 bottom-mount refrigerator Parts

A Kenmore Elite 79574073810 bottom-mount refrigerator typically lasts 10 to 15 years. Regular maintenance (especially keeping airflow clear and doors sealing tightly) helps you reach the high end of that range and reduces the chance of expensive sealed-system repairs.

Most refrigerators fall into a similar life range, but real-world lifespan depends heavily on operating conditions and upkeep.

Common factors that shorten lifespan:

• Dirty condenser area causing longer run times and higher heat
• Worn or leaking door gaskets letting warm, moist air in
• Frequent door openings and overpacking that restricts airflow
• Power interruptions and repeated warm-ups
• Poor temperature settings (too cold can increase run time and frost)

Use these habits to reduce compressor workload and stabilize temperatures:

• Keep the refrigerator and freezer vents inside the compartments unblocked
• Set and confirm temps stay near 37°F (fresh food) and 0°F (freezer)
• Allow up to 24 hours to fully cool after installation or after power is restored
• Keep doors closed as much as possible; organize food so you grab items quickly
• Replace the water filter on schedule if you use the dispenser

For model-specific care and operating guidance, follow the 79574073810 owner's manual.

When a refrigerator is in the middle or late part of its lifespan, high-cost cooling-system repairs can outweigh the value of keeping it.

If cooling performance points to a compressor problem, the refrigerator compressor TCA38091801 is a model-matched replacement part option.

A refrigerator that runs longer than normal uses more energy and puts extra wear on the compressor and evaporator system. Keeping temperatures stable and airflow clear is the simplest way to protect the most expensive components.

Last updated: February 2026

On the Kenmore Elite 79574073810 bottom-mount (bottom freezer) refrigerator, the water filter is located inside the fresh food (refrigerator) compartment, typically at the upper left area behind a small filter cover. The exact placement and access steps are shown in the 79574073810 owner's manual.

Look in the refrigerator section (not the freezer drawer) for a small cover labeled for the filter.

• Open the refrigerator door and check the upper left interior wall/ceiling area
• Look for a water filter cover you can pinch or pull open
• If a shelf blocks access, lower or remove the top left shelf first
• Keep a cup handy; a small amount of water can drip when the filter is removed

These steps match the water filter procedure described for this model family.

1. Lower or remove the top left shelf so the filter can rotate down.
2. Pinch the sides to open the filter cover.
3. Rotate the filter down fully, then pull down and turn it counterclockwise to remove.

Knowing the filter location helps you replace it on schedule (about every 6 months) and restore normal water dispenser flow and ice cube size. A properly seated filter also helps prevent leaks at the manifold.

If you are replacing the cartridge, use the model-matched filter listed for this refrigerator, such as the genuine Kenmore refrigerator water filter 9980 AGF80300805.

Last updated: February 2026

On Kenmore Elite model 79574073810, the model and serial number are printed on an identification label inside the fresh food (refrigerator) compartment, on the interior liner. We use that label information to match the correct parts and diagrams for your exact unit; especially important for 795.7407* color variations.

Look for a paper or foil label in one of these spots:

• Inside the refrigerator compartment on a side wall (interior liner)
• On the ceiling area inside the fresh food section
• Near the crisper drawer area (often on the liner behind or beside drawers)
• On the door frame area (visible when the door is open)
• Under the front grille area, if you are looking for the tech sheet (not the same as the ID label)

The label typically includes both numbers; record them exactly as shown:

• Model number (for example, 795.7407* family; your full model is 79574073810)
• Serial number
• Date of purchase (helpful for warranty and service records)

Kenmore Elite bottom-mount refrigerators often share a model family (like 795.7407*), but parts can vary by exact model and color code. Using the identification label prevents ordering the wrong water filter, ice maker, or control parts.

For diagrams and additional identification details, use the 79574073810 owner's manual.

Last updated: February 2026

Common issues we see with the Kenmore Elite 79574073810 bottom-mount refrigerator are “not cooling” or “too warm” complaints (often tied to settings, airflow, or defrost-related conditions), long run times after a power interruption, ice maker or dispenser problems, and water supply issues that affect the ice maker and water dispenser. For model-specific checks and diagnostics, use the owner's manual.

• Refrigerator and freezer not cooling: controls set to OFF, unit in demo mode, or unit currently in a defrost cycle
• Too warm in one section: blocked air vents, frequent door openings, hot food load, or installation in a hot location
• Runs a lot after outage or first plug-in: normal for up to 24 hours while temperatures stabilize
• No ice or slow ice: water supply/pressure issue, inlet valve issue, or ice maker assembly problem
• Water dispenser weak or no water: filter restriction, low water pressure, or inlet valve issue
• Hard-to-open doors: normal vacuum effect right after closing; dirty or sticky door gaskets

1. Confirm the temperature controls are ON and set correctly (not OFF).
2. Make sure the refrigerator is not in demo mode (lights work but cooling is disabled).
3. Check that air vents are not blocked by food packages.
4. After a move, let the refrigerator stand upright 24 hours before powering it on.
5. After power is restored, allow up to 24 hours for full cooling.
6. Verify the room temperature is within the operating range (avoid locations above 110°F).

Your refrigerator’s water system is designed around these requirements:

If you suspect a component failure, common related parts for this model include the lg refrigerator water inlet valve AJU72992603, the lg refrigerator ice maker AEQ73130004, and the refrigerator defrost sensor assembly 6615JB2005R.

Warm temperatures, restricted airflow, and low water pressure can look like “major” failures, but they often come from settings, vent blockage, or normal recovery time after installation or a power interruption. Starting with the basics prevents unnecessary part replacement.

Last updated: February 2026

If your Kenmore Elite refrigerator model 79574073810 is warm in both sections and you hear repeated clicking or short run cycles, the compressor may be failing. First rule out normal long run times (up to 24 hours after power is restored) and airflow issues before suspecting the compressor.

• Confirm the unit has had up to 24 hours to cool after being plugged in or after a power outage.
• Make sure doors close fully and are not being held open by bins or food packages.
• Check room temperature; the refrigerator should not be operated above 110°F.
• Clean dust from the condenser cover and vents using a vacuum attachment (do not remove the condenser area panel).
• Listen for normal sounds: whooshing, gurgling, and some clicking can be normal operation.

A compressor problem is more likely when basic conditions are good (doors shut, vents clear, reasonable room temp) but cooling still fails.

• Repeated clicking every few minutes with little or no sustained running (overload/relay cycling)
• Compressor runs but does not cool (both fridge and freezer temperatures rise)
• Unusual loud buzzing/humming followed by a click and shutdown
• Compressor is very hot to the touch and keeps shutting off (overheating/overload)
• Fans may run normally, but temperatures do not recover

1. Listen and observe: does it run steadily, or click on and off?
2. Check airflow: verify the condenser area vents are not clogged with dust.
3. Temperature pattern: if only the refrigerator section is warm but the freezer is OK, the issue is often airflow/defrost, not the compressor.

For model-specific diagnostic steps and the troubleshooting flow, use the owner's manual.

Compressors are part of the sealed refrigerant system; misdiagnosing can lead to unnecessary cost. Ruling out door, airflow, and “normal operation” noises first helps you target the real failure faster.

If you determine the compressor is the issue, the correct replacement for this model is the refrigerator compressor TCA38091801.

Last updated: February 2026