Kenmore 11026442501 washer Parts

Kenmore model numbers are read left to right: the first three digits identify the manufacturer series, and the remaining digits identify the specific design and feature set. For Kenmore washer model 11026442501, the 110 prefix is the key identifier, and the full number is what we use to match the correct parts and diagrams.

For Kenmore 11026442501, the model and serial label is located under the washer lid. This is the number you should use when ordering parts or checking specifications in the owner's manual.

• Lift the lid and look around the underside of the top panel opening
• Write down the full model number (all digits)
• Record the serial number and purchase date for your records
• Keep the information with your manual for future repairs

Kenmore numbers are structured so the prefix points to the manufacturing source, and the rest narrows down the exact configuration.

A single digit difference can change the correct replacement part. Using the complete model number helps us match components like the washer lid switch assembly WP8318084 or washer drain pump WP3363394 to your exact Kenmore washer.

• Prevents ordering the wrong part revision
• Ensures wiring harness and mounting points match
• Helps confirm compatibility for drive system parts (coupling, clutch, motor)
• Speeds up troubleshooting by matching the correct diagrams

Always search and order using the full model number (all digits), not just the 110 prefix. That is the fastest way to pull the correct parts list for Kenmore 11026442501.

Last updated: February 2026

For Kenmore washer model 11026442501, a “hard reset” is a simple power reset: unplug the washer (or switch off the breaker) for 2 minutes, then restore power and run a cycle. This clears a temporary control glitch and is the fastest first step; see the 11026442501 owner's manual for normal start/stop operation.

• Turn the cycle control knob to Off.
• Unplug the washer (or turn the breaker off).
• Wait 2 minutes.
• Restore power.
• Set a cycle and pull the cycle control knob out to start.
• If the washer will not start, close the lid firmly and try again.

A reset helps when the washer is “stuck” between steps, the timer seems confused, or the washer will not restart after you stopped it.

• Make sure the lid is closing and latching consistently; a failed lid switch can prevent spin or agitation (common on top-load designs).
• Verify the washer is level; an unlevel cabinet can cause out-of-balance behavior and cycle interruptions (leveling steps are in the installation guide).
• Reduce the load size and redistribute items so the load can move freely.
• If the cycle control knob feels loose, skips, or stalls, the timer can be the cause; compare behavior to the cycle descriptions in the manual.

Resetting first prevents unnecessary part replacement. If the issue returns quickly, the washer is usually reacting to a real condition (lid switch, drain problem, unbalanced load, or a worn drive component) rather than a one-time control glitch.

Last updated: February 2026

The cubic feet capacity for Kenmore washer model 11026442501 is found in the model’s specifications in the owner's manual. If you do not see a cubic-feet number listed, you can calculate the wash basket volume from measurements to get a reliable working capacity.

Use the model-specific documentation first so you get the manufacturer’s stated spec.

• Open the owner's manual
• Check sections labeled Specifications, Features, or Washer dimensions
• Look specifically for capacity, cu. ft., or basket volume
• Confirm the model number shown is 11026442501

Measure the inside of the basket and convert the volume to cubic feet.

• Measure inside diameter of the basket (in inches)
• Measure usable depth (in inches) from the bottom to the normal maximum fill level you use
• Calculate cubic inches: π × (diameter/2)² × depth
• Convert to cubic feet: cubic inches ÷ 1,728

Capacity affects load size, detergent amount, and balance during spin. Keeping loads within the washer’s usable volume helps prevent out-of-balance shaking and reduces wear on drive components.

Last updated: February 2026

To unclog the drain hose on your Kenmore washer model 11026442501, unplug the washer, remove standing water, then clear the drain path from the standpipe connection back to the pump. Reinstall the hose with the correct height and an air gap so it drains and spins normally.

• Unplug the washer; turn off water if you need to move it.
• Keep towels and a shallow pan ready.
• Remove as much water as possible (bail out or wet/dry vacuum at the hose end).
• Avoid repeatedly restarting a drain cycle while it is restricted.

1. Check the outlet first: Pull the hose end from the standpipe or laundry tub and remove any lint, coins, or fabric at the opening.
2. Flush the hose: Run water through the hose (sink or outdoor hose) until it flows freely.
3. Inspect the pump inlet: Follow the hose to the pump and clear debris from the pump inlet and impeller area.
4. Reinstall correctly: Route and secure the hose the way Kenmore specifies in the installation guide.

The washer can drain poorly if the hose is installed incorrectly.

• Keep the hose loose but secure in the standpipe; do not tape or seal it (it needs an air gap).
• Keep the drain height within the required range.
• Do not force excess hose down into the standpipe.

If the hose is clear but the washer still will not drain or spin, these are common fixes:

• Washer drain pump WP3363394 (jammed, noisy, leaking, or not pumping)
• Washer lid switch assembly WP8318084 (won’t spin if the lid switch fails)

A partial clog or incorrect drain hose height can leave water in the tub, stop the spin cycle, and make the cycle seem stuck. Correct routing and an air gap help prevent repeat drain problems.

Last updated: February 2026