Kenmore 11026442501 washer Parts

Kenmore model numbers are read left to right: the first three digits identify the manufacturer series, and the remaining digits identify the specific design and feature set. For Kenmore washer model 11026442501, the 110 prefix is the key identifier, and the full number is what we use to match the correct parts and diagrams.

Where to find the model number on this washer

For Kenmore 11026442501, the model and serial label is located under the washer lid. This is the number you should use when ordering parts or checking specifications in the owner's manual.

• Lift the lid and look around the underside of the top panel opening
• Write down the full model number (all digits)
• Record the serial number and purchase date for your records
• Keep the information with your manual for future repairs

What the digits mean (simple breakdown)

Kenmore numbers are structured so the prefix points to the manufacturing source, and the rest narrows down the exact configuration.

Model number section	What it tells you	Why it matters
First 3 digits (example: 110)	Manufacturer prefix/series	Helps identify the correct parts system and design family
Remaining digits	Exact model configuration	Ensures the right fit for parts like a lid switch, pump, or timer

Why it matters for parts and troubleshooting

A single digit difference can change the correct replacement part. Using the complete model number helps us match components like the washer lid switch assembly WP8318084 or washer drain pump WP3363394 to your exact Kenmore washer.

• Prevents ordering the wrong part revision
• Ensures wiring harness and mounting points match
• Helps confirm compatibility for drive system parts (coupling, clutch, motor)
• Speeds up troubleshooting by matching the correct diagrams

Quick tip for ordering parts

Always search and order using the full model number (all digits), not just the 110 prefix. That is the fastest way to pull the correct parts list for Kenmore 11026442501.

Last updated: February 2026

For Kenmore washer model 11026442501, a “hard reset” is a simple power reset: unplug the washer (or switch off the breaker) for 2 minutes, then restore power and run a cycle. This clears a temporary control glitch and is the fastest first step; see the 11026442501 owner's manual for normal start/stop operation.

Hard reset (power reset) steps

• Turn the cycle control knob to Off.
• Unplug the washer (or turn the breaker off).
• Wait 2 minutes.
• Restore power.
• Set a cycle and pull the cycle control knob out to start.
• If the washer will not start, close the lid firmly and try again.

What a reset can and cannot fix

A reset helps when the washer is “stuck” between steps, the timer seems confused, or the washer will not restart after you stopped it.

Symptom	Reset likely helps?	What to check next
Washer won’t restart after stopping	Yes	Lid fully closed; cycle knob pushed in then pulled out to start
Won’t drain or drains slowly	Sometimes	Kinked drain hose; pump obstruction; consider washer drain pump WP3363394
Won’t spin or agitates poorly	Sometimes	Load balance; drive components like agitator dog 80040
Completely dead (no response)	Sometimes	Outlet power; breaker; timer or lid switch issues

If the washer still won’t run after the reset

• Make sure the lid is closing and latching consistently; a failed lid switch can prevent spin or agitation (common on top-load designs).
• Verify the washer is level; an unlevel cabinet can cause out-of-balance behavior and cycle interruptions (leveling steps are in the installation guide).
• Reduce the load size and redistribute items so the load can move freely.
• If the cycle control knob feels loose, skips, or stalls, the timer can be the cause; compare behavior to the cycle descriptions in the manual.

Why it matters

Resetting first prevents unnecessary part replacement. If the issue returns quickly, the washer is usually reacting to a real condition (lid switch, drain problem, unbalanced load, or a worn drive component) rather than a one-time control glitch.

Last updated: February 2026

The cubic feet capacity for Kenmore washer model 11026442501 is found in the model’s specifications in the owner's manual. If you do not see a cubic-feet number listed, you can calculate the wash basket volume from measurements to get a reliable working capacity.

Where to find the rated capacity

Use the model-specific documentation first so you get the manufacturer’s stated spec.

• Open the owner's manual
• Check sections labeled Specifications, Features, or Washer dimensions
• Look specifically for capacity, cu. ft., or basket volume
• Confirm the model number shown is 11026442501

How to calculate capacity (if you need a working number)

Measure the inside of the basket and convert the volume to cubic feet.

• Measure inside diameter of the basket (in inches)
• Measure usable depth (in inches) from the bottom to the normal maximum fill level you use
• Calculate cubic inches: π × (diameter/2)² × depth
• Convert to cubic feet: cubic inches ÷ 1,728

Item	What to measure	Why it matters
Inside diameter	Wall-to-wall inside the basket	Sets the basket’s cross-sectional area
Usable depth	Bottom to typical max fill level	Prevents overstating volume
Calculated cu. ft.	Volume ÷ 1,728	Gives a practical capacity estimate

Why it matters

Capacity affects load size, detergent amount, and balance during spin. Keeping loads within the washer’s usable volume helps prevent out-of-balance shaking and reduces wear on drive components.

Last updated: February 2026

To unclog the drain hose on your Kenmore washer model 11026442501, unplug the washer, remove standing water, then clear the drain path from the standpipe connection back to the pump. Reinstall the hose with the correct height and an air gap so it drains and spins normally.

Safety and prep

• Unplug the washer; turn off water if you need to move it.
• Keep towels and a shallow pan ready.
• Remove as much water as possible (bail out or wet/dry vacuum at the hose end).
• Avoid repeatedly restarting a drain cycle while it is restricted.

Step-by-step: clear the clog

1. Check the outlet first: Pull the hose end from the standpipe or laundry tub and remove any lint, coins, or fabric at the opening.
2. Flush the hose: Run water through the hose (sink or outdoor hose) until it flows freely.
3. Inspect the pump inlet: Follow the hose to the pump and clear debris from the pump inlet and impeller area.
4. Reinstall correctly: Route and secure the hose the way Kenmore specifies in the installation guide.

Drain setup checks (prevents “false clogs”)

The washer can drain poorly if the hose is installed incorrectly.

• Keep the hose loose but secure in the standpipe; do not tape or seal it (it needs an air gap).
• Keep the drain height within the required range.
• Do not force excess hose down into the standpipe.

Drain hose requirement	Spec for 11026442501	Why it matters
Minimum height	39 in. above floor	Prevents drain and cycle issues
Maximum height	96 in. above floor	Prevents weak or no draining
Air gap	Not sealed to standpipe	Prevents siphoning and slow drain

When a part is the real problem

If the hose is clear but the washer still will not drain or spin, these are common fixes:

• Washer drain pump WP3363394 (jammed, noisy, leaking, or not pumping)
• Washer lid switch assembly WP8318084 (won’t spin if the lid switch fails)

Why it matters

A partial clog or incorrect drain hose height can leave water in the tub, stop the spin cycle, and make the cycle seem stuck. Correct routing and an air gap help prevent repeat drain problems.

Last updated: February 2026