Kenmore Elite 79572053110 refrigerator Parts

To level your Kenmore Elite refrigerator model 79572053110, adjust the two front leveling legs until the cabinet is steady and the doors close smoothly. For best door closing, set the front slightly higher than the rear, then recheck door operation.

What to do (leveling steps)

• Unplug the refrigerator or switch off power for safety.
• Pull the refrigerator forward enough to access the front leveling legs.
• Use an 11/16-inch wrench or a flat-blade screwdriver (as applicable) to turn the leveling legs.
• Turn the leveling leg left to raise that side; turn it right to lower that side.
• Adjust side-to-side first (stop rocking), then adjust front-to-back so doors close easily.
• Recheck by opening both fresh food doors and confirming they close without drifting open.

Quick reference: which way to turn?

Goal	Turn leveling leg	Result
Raise that side	Left	Front corner goes up
Lower that side	Right	Front corner goes down
Improve door closing	Raise front slightly	Helps doors self-close

Door not lining up after leveling?

This model uses two fresh food doors; after leveling, you can fine-tune alignment at the bottom hinges.

• Check the gap between the left and right doors.
• If the gap is uneven, use the hinge adjustment nut(s) described in the 79572053110 owner's manual.
• Make small adjustments, then recheck the door gap and closing.

Why it matters

A refrigerator that is not level can vibrate, rock when doors open, and struggle to seal properly. A good seal helps maintain stable temperatures, reduces frost issues, and supports efficient compressor run time.

Last updated: February 2026

Common problems on the Kenmore Elite 79572053110 bottom-mount refrigerator include weak or uneven cooling, frost buildup from defrost issues, water or ice dispenser troubles, and door sealing problems that cause temperature swings. Many of these are fixed with cleaning, airflow checks, or replacing a failed component.

Most common symptoms and what usually causes them

• Not cooling or warm temperatures: dirty condenser coil, failed compressor, or airflow restriction
• Freezer cold but fridge warm: air damper stuck, blocked vents, or evaporator fan/defrost issue
• Frost buildup or ice on the back wall: defrost sensor or defrost system problem
• Ice maker not making ice: water supply issue, clogged filter, or ice maker assembly problem
• Water leaking or puddles: clogged drain, loose water line, or door not sealing

For model-specific troubleshooting steps and checks, use the 79572053110 owner's manual.

Quick checks we recommend before replacing parts

1. Confirm settings: fridge around 37°F, freezer around 0°F.
2. Check airflow: do not block vents with food packages.
3. Clean heat-exchange area: vacuum dust from the condenser area and grille.
4. Inspect door seal: look for gaps, tears, or areas that do not grip paper.
5. Reset after power issues: allow 24 hours after a power interruption or major setting change.

Common fixes and related parts (when symptoms match)

Symptom	Likely area	Example part for this model
Bad taste/slow water flow	Water filter	Genuine Kenmore refrigerator water filter 9690 AGF80300801
Odors in fresh food section	Air filtration	Lg refrigerator air filter ADQ73214408
Frost/temperature swings	Defrost sensing	Refrigerator defrost sensor assembly 6615JB2005R
Lights or alarms act odd when door closes	Door sensing	Refrigerator door switch 6600JB1010A
No ice production	Ice maker	Refrigerator ice maker assembly AEQ73110205

Why it matters

Cooling and ice maker complaints often start with restricted airflow or dirty condenser components, which forces longer run times and can lead to bigger failures. Catching a door gasket leak or defrost problem early helps protect food temperatures and reduces strain on the sealed system.

Helpful DIY guides

• Kenmore 795 model bottom freezer refrigerator error codes
• How to replace the water filter in a Kenmore refrigerator

Last updated: February 2026

If your Kenmore Elite refrigerator model 79572053110 is warmer at the bottom, the most common cause is restricted airflow: cold air is not circulating down into the fresh food section. Start by clearing blocked vents, confirming the temperature controls are ON (not OFF or demo mode), and allowing time after changes for temperatures to stabilize (up to 24 hours after installation).

Quick checks that fix most “warm at the bottom” complaints

• Move food packages away from interior air vents so air can flow freely.
• Make sure the controls are not set to OFF and the unit is not in demo mode (cooling disabled).
• Reduce long or frequent door openings; warm air quickly pools in the lower area.
• Wait 30 minutes after a defrost cycle for temperatures to recover.
• If the refrigerator was recently installed or moved, allow up to 24 hours to reach set temperatures.

For control locations and the airflow diagram, follow the steps in the 79572053110 owner’s manual.

What to check next (when airflow is clear)

If vents are clear and settings are correct, focus on components that affect cooling and air movement.

Symptom	What it often points to	What to do first
Top shelves cool, bottom warm	Airflow restriction or damper issue	Recheck vent blockage; inspect damper area for frost/obstructions
Both sections too warm	Cooling system not running efficiently	Confirm not in demo mode; listen for fans/compressor; check for heavy frost
Warm after loading groceries	Normal recovery time	Give it several hours; avoid overpacking

Parts that may be involved

These parts are commonly related when cooling is uneven or weak:

• Refrigerator air damper ADJ73252235 (controls cold air entering the fresh food section)
• Refrigerator evaporator ADL73341411 (absorbs heat; heavy frost here can block airflow)
• Refrigerator defrost sensor assembly 6615JB2005R (defrost system feedback; failures can lead to frost buildup)

Why it matters

Bottom-warm conditions usually mean the refrigerator cannot move cold air where it is needed. That can cause food to spoil faster, increase run time, and lead to frost or condensation problems if airflow stays restricted.

Last updated: February 2026