Kenmore 58715189402 dishwasher Parts

Common problems on the Kenmore 58715189402 dishwasher are poor cleaning, not draining, leaking, not starting, and weak drying. Most of these trace back to loading and detergent issues, blocked spray arms or filters, low water temperature or pressure, or a worn seal, hose, or heating component (see the 58715189402 owner's manual).

Most common symptoms and what usually causes them

• Food soils left on dishes: blocked spray arms, items nesting, old detergent, low incoming water temp
• Detergent left in the cup: dispenser blocked by dishes, cycle interrupted, old detergent
• Leaks or water on the floor: excess suds from wrong detergent, rinse aid spill, unit not level, worn door seal
• Not draining or water left in tub: drain path restriction, drain hose routing issue, drain pump problem
• Not drying well: HEAT DRY not selected, rinse aid low, heating circuit issue

Quick checks we recommend first (fast, no tools)

1. Confirm incoming hot water is about 120°F (49°C).
2. Make sure home water pressure is roughly 20 to 120 psi.
3. Reload so nothing blocks spray arms and the detergent dispenser can open.
4. Use fresh automatic dishwasher detergent; avoid hand soap and excessive detergent.
5. If you see foam, wipe up any spilled rinse aid and rerun a cycle.

Parts that commonly fix these problems on model 58715189402

Symptom	Common part to inspect	What it affects
Leaking at the door	Dishwasher door seal 809006501	Seals the tub to the door to prevent drips
Not draining	Hose 807117001	Drain path from dishwasher to disposal or drain
Not filling	Valve 154637401	Water supply into the dishwasher
Not drying	Heater 154665201	Water heating and heated drying

Why it matters

These issues often look like a “bad dishwasher,” but they are usually performance basics (water temp, pressure, loading) or a single wear part. Fixing the root cause improves cleaning, prevents leaks, and helps the wash system recirculate filtered water the way it was designed.

Last updated: January 2026

Yes. Your Kenmore dishwasher model 58715189402 uses a built-in, self-cleaning filter system that filters the wash water for cleaning performance, and it also includes a glass trap area designed to catch debris like broken glass. See the 58715189402 owner's manual for the exact filter and glass trap locations.

What type of filter this dishwasher uses

This model is designed to keep wash water circulating through a filter system during the cycle.

• The filter is described as self-cleaning during normal use
• Wash water passes through a fine mesh primary filter
• Food soil is directed through a secondary filter into a collection chamber
• A glass trap in the center of the filter can be lifted out to remove debris

How to check and clean the glass trap (safe, routine maintenance)

We recommend doing this if you hear rattling, see debris left behind, or suspect broken glass.

1. Turn off power at the breaker (recommended for safety).
2. Pull out the lower rack for access.
3. Locate the glass trap area near the center of the tub floor.
4. Lift the trap out by its handle, empty it, then reinstall it fully.

Quick do and do not list

• Do let the heating element cool before reaching into the tub
• Do rinse the trap and surrounding area with water if needed
• Do not run the dishwasher if the trap is not seated correctly
• Do not use abrasive cleaners inside the tub

When a “filter problem” is really a leak or drain issue

If you are seeing water on the floor or poor draining, the issue is usually not the self-cleaning filter itself.

Symptom	Common cause	Part to inspect on this model
Water leaking at the door	Worn or loose door seal	Dishwasher door seal 809006501
Dishwasher not draining well	Kinked/clogged drain hose or weak drain pump	Hose 807117001

Why it matters

A clear filter path and an empty glass trap help your Kenmore 58715189402 maintain strong spray-arm pressure, reduce redepositing food soil, and prevent debris from damaging the pump area.

Last updated: January 2026

To hard reset a Kenmore dishwasher model 58715189402, we recommend canceling the current cycle and letting the control clear; press START/CANCEL to run the built-in drain (about 90 seconds), then reselect your wash cycle. For model-specific button sequences, use the 58715189402 owner's manual.

Quick reset methods that work on most Kenmore dishwashers

• Cancel and drain reset: Press START/CANCEL once; wait for the drain to finish, then choose a new cycle.
• Power reset: Turn the dishwasher off at the breaker for 5 minutes, then restore power.
• Door reset: Close the door fully and latch it; many models will not respond until the latch is engaged.

Step-by-step: cancel and restart (recommended)

1. Press START/CANCEL.
2. Wait for the drain to complete (typically about 90 seconds).
3. Select the desired cycle and options.
4. Press START and close the door to begin.

If the dishwasher still will not respond

Check these common causes before replacing parts:

• House breaker is on and the dishwasher has power.
• Door is closing and latching smoothly.
• Control is not in Delay Start mode.
• Water supply valve is open and household water pressure is adequate.
• The tub is not overfilled; the float (overfill protector) should move freely.

Symptom after reset	Most likely area to check	What to do next
Won’t start at all	Door latch system	Inspect latch alignment; review the 58715189402 owner's manual start steps
Won’t drain	Drain path	Check for kinks/clogs; inspect the hose 807117001
Stops mid-cycle	Heating or water temp	Verify incoming water is hot (about 120°F for best results)

Why it matters

A proper reset clears a stuck cycle and forces the dishwasher to drain safely, which helps prevent standing water, odor, and false “won’t start” symptoms caused by an incomplete prior cycle.

Last updated: January 2026

On Kenmore dishwasher model 58715189402, an F2 E2 error is typically cleared by resetting the user interface: press and hold START/CANCEL for about 3 to 5 seconds to cancel the cycle and let the control reset, then reselect a cycle and start it.

Reset steps (58715189402)

• Press START/CANCEL and hold for 3 to 5 seconds.
• Wait for the dishwasher to begin its cancel-drain (many models run a short drain after cancel).
• When the drain finishes, select your desired cycle.
• Press START/CANCEL again to start.
• If the code returns immediately, turn off power at the breaker for 1 minute, then restore power and try again.

What to check if F2 E2 comes back

F2 E2 is commonly tied to a keypad or control communication issue. These checks help rule out simple causes before replacing parts:

• Make sure the door is fully closed and latched; a partial latch can interrupt the control.
• Wipe the control panel and buttons dry; moisture can cause false key presses.
• Press each key once; a stuck key feel (does not click or releases slowly) points to a keypad problem.
• Cancel the cycle and restart using the normal start procedure in the 58715189402 owner's manual.
• If the dishwasher will not reliably start or cancel, inspect the door latch area and consider the latch assembly A00099902 if the latch is not holding consistently.

Quick reference

Symptom	What it usually means	Best next step
Code clears, then returns during use	Intermittent keypad/control issue	Dry panel, retry reset, power cycle
Code returns immediately after reset	Stuck key or control input fault	Check for stuck buttons, inspect latch
Dishwasher will not start at all	Door not latched or control not accepting input	Verify latch, then follow manual start steps

Why it matters

Resetting clears the active fault and stops the cycle safely, but if F2 E2 keeps returning it usually indicates an input problem (keypad/control or door-latch related) that can prevent the dishwasher from starting, canceling, or completing cycles correctly.

Last updated: January 2026