Kenmore 79072503011 gas range Parts

Yes. Kenmore makes gas ranges, including the Kenmore 79072503011 gas range, which uses gas burners for cooking and electric ignition for lighting the burners. For model-specific features, safety guidance, and operating details, use the 79072503011 use and care guide.

A Kenmore gas range combines a gas cooktop with a gas oven burner system (bake and broil) that is typically lit by an electric igniter.

Common benefits you can expect from a Kenmore gas range:

• Fast burner response when you turn the knob up or down
• Strong heat output for boiling and searing
• Visual flame feedback to help you fine-tune heat
• Reliable oven ignition when the igniter and gas valve are working correctly
• Standard safety requirements for ventilation and combustion air

For the Kenmore 79072503011, proper airflow and correct installation clearances matter for safe burner combustion and normal oven venting. We recommend following the 79072503011 installation guide for placement, gas supply hookup, and anti-tip bracket setup.

Key points to follow:

• Keep the oven vent and lower front area unobstructed
• Do not seal the range to side cabinets
• Use the anti-tip bracket as instructed
• Do not use a downward-blowing “air curtain” hood unless it is specifically listed for use with the range
• During a power outage, do not try to operate the electric-ignition oven; surface burners can be match-lit with extreme caution

Knowing that Kenmore makes gas ranges helps you choose the right parts and troubleshooting steps. For example, weak or no oven ignition often points to an igniter issue such as the tappan range oven burner igniter 316489403, while inaccurate oven temperatures often relate to the frigidaire range oven temperature sensor 316490000.

Last updated: February 2026

On the Kenmore 79072503011 gas range, the most commonly replaced parts are ignition and heating-related items (igniters, burner components, sensors) plus wear items (light bulb, racks, knobs, grates). These parts take the most heat and use, so they fail first and cause no-heat or poor-heating symptoms.

• Oven igniter: oven will not heat, slow ignition, gas smell before ignition (often a weak igniter)
• Oven temperature sensor: oven temperature is inaccurate, overbakes or underbakes
• Surface burner ignition parts: clicking but no flame, intermittent lighting
• Oven light bulb: light out even though the oven works normally
• Oven racks and grates: rust, warping, broken welds, or heavy wear from cleaning and high heat

These are common, high-wear parts we see replaced on this model:

• Confirm whether the problem is bake, broil, or surface burners only.
• For ignition issues, watch for glow at the igniter (oven) or spark at the electrode (cooktop).
• If the oven heats but cooks unevenly, verify rack position and avoid blocking airflow.
• If you replace the oven light, shut off power and use a 40-watt appliance bulb.
• Use the wiring diagram and component locations in the 79072503011 owner's manual to match symptoms to the correct part.

Replacing the correct high-failure part first saves time and prevents repeat repairs. For example, a weak igniter can look like a gas valve problem, and a drifting temperature sensor can mimic “oven not heating right” complaints.

Last updated: February 2026

For Kenmore gas range model 79072503011, the cooktop (top) is not removable, so we do not remove the top panel for service. For cleaning and most repairs, we access components by removing surface parts (grates, burner caps) and using the service access points described in the 79072503011 installation guide.

• Lift off the burner grates.
• Remove the burner caps.
• Lift off the burner heads (if your burner style allows it) and clean ports.
• Pull the control knobs straight off (for cleaning around the valve stems).
• Remove the oven racks if you are working inside the oven cavity.

If you are trying to reach wiring, igniters, or gas components, use the access method that matches the symptom:

• Turn all controls to OFF and let surfaces cool.
• Shut off the gas supply if you are moving the range for service.
• Disconnect power before working near wiring or switches.
• If you pull the range out, keep it level and verify the anti-tip setup when reinstalling.

Trying to force a non-removable cooktop can bend panels, damage gas tubing, or create ignition and wiring problems. Using the correct access method protects the manifold, igniters, and burner alignment.

Last updated: February 2026

A Kenmore gas range like model 79072503011 typically lasts 15 years with normal household use. Keeping burners clean, confirming proper ignition, and replacing wear items such as igniters and light bulbs on time helps you reach that lifespan.

Most ranges reach their full service life when heat output stays consistent and the gas and ignition systems stay clean and properly adjusted.

• Heavy daily cooking shortens lifespan faster than occasional use
• Spills and boil-overs that clog burner ports cause poor flames and extra wear
• Weak ignition (slow lighting) stresses the gas valve and igniter system
• Overheating from blocked airflow can damage controls and wiring
• Skipping routine cleaning leads to corrosion and sticking valves

Use the care and cleaning steps in the 79072503011 owner's manual and focus on these basics:

• Clean surface burner caps and heads; keep ports clear
• Wipe up spills quickly to prevent baked-on residue
• Verify each surface burner lights promptly and the flame looks steady
• Keep the oven interior reasonably clean to avoid smoke and excess heat
• Replace worn consumables (for example, oven light bulbs) as needed

The installation instructions for this range describe normal surface-burner ignition as lighting within about 4 seconds after air is purged from the gas lines.

If the oven or broil burner struggles to ignite, a failing igniter is a common cause. For this model, a frequently used replacement is the tappan range oven burner igniter 316489403.

A range that lights quickly and burns with a stable flame runs cooler at the controls, cooks more evenly, and avoids repeated ignition cycling that shortens component life.

Last updated: February 2026

Your Kenmore gas range model number is printed on the identification plate (serial plate) on the oven front frame. On model 79072503011, you typically access it by opening the storage drawer, warmer drawer, or broiler drawer and looking on the right-hand surface of the oven front frame; confirm the exact location in the 79072503011 installation guide.

Check these common spots in this order:

• Open the storage drawer (if your range has one) and look at the right-hand oven front frame
• Open the warmer drawer (some models) and check the same right-hand frame area
• Open the broiler drawer (some models) and check the right-hand frame area
• Look for a label that lists model, serial, and sometimes a lot number/letter

When we help you match parts or troubleshoot, these details matter:

• Model number (example: 79072503011)
• Serial number (unique to your range)
• Lot number or letter (often used to confirm production variation)
• Fuel type and pressure info shown on the plate (helps with gas setup and conversion questions)

Using the exact model number prevents ordering the wrong igniter, burner parts, or control components for your Kenmore gas range; even small model variations can change fit and wiring.

Last updated: February 2026