Kenmore 58716169400 dishwasher Parts

Yes. We still carry replacement parts for Kenmore dishwashers, including model 58716169400; the key is matching parts by the full model number so you get the correct fit for items like door seals, drain hoses, inlet valves, and heating components. See the 58716169400 owner's manual for model-specific component locations and care guidance.

How to make sure you order the right part

• Use the complete model number 58716169400 (from the rating label) when searching parts.
• Match the symptom to the system (leak, no drain, no fill, poor cleaning, not heating).
• Compare your original part’s shape, ports, and electrical connectors before installing.
• Replace seals and gaskets when you see flattening, tears, or mineral buildup.
• For installation-related items (hoses, anchoring, leveling), follow the 58716169400 installation guide.

Common parts customers replace on 58716169400

Here are examples of in-stock parts for this model that cover frequent repairs:

Problem you see	Likely part to check	Example model-matched part
Water leaking at the bottom of the door	Lower door seal	Gasket 809006501
Dishwasher will not drain or drains slowly	Drain hose, drain pump, clogs	Hose 807117001
Dishwasher will not fill or fills too slowly	Water inlet valve, supply issues	Valve 154637401
Poor drying or water not heating	Heater circuit, element hardware	Heater 154665201

Why it matters

Kenmore dishwashers are built with model-specific mounting points, seals, and electrical connectors. Using the exact 58716169400 model number helps prevent leaks, drain problems, and repeat repairs caused by near-match parts.

Last updated: February 2026

Your Kenmore dishwasher model number is on the model and serial number label, typically located inside the door opening on the inner door frame or tub edge. For this series, the manual shows the model number format as 587. followed by additional digits (example: 58716169400). See the 58716169400 owner's manual for the exact label location diagram.

Where to look first (fastest checks)

• Open the door and inspect the top and sides of the inner door frame.
• Check the tub rim around the door opening.
• Look along the inside edge of the door near the latch area.
• If the label is worn, use a flashlight and view from an angle to read faint printing.

If you still cannot find the label

Sometimes the label is obscured by residue or positioned where it is easy to miss.

• Wipe the door frame and tub rim with a damp cloth and mild cleaner.
• Check the lower edge of the door opening (near the bottom seal area).
• Look for a metal plate or white sticker that lists both model and serial.
• Use your paperwork: the model number is often recorded in the 58716169400 owner's manual “record your model and serial number” section.

What the model number looks like for Kenmore 587 models

The manual indicates this platform uses a model number that begins with 587. (Kenmore 587 series). Your full model is the complete string without spaces.

What you see on the label	What it means	Example
587.XXXXXXXX	Model prefix + full identifier	58716169400
Serial number	Unique unit identifier	Varies

Why it matters

We use the full model number to match the correct parts and diagrams for your exact dishwasher configuration (rack style, door components, and wash system variations). That prevents ordering the wrong items and speeds up troubleshooting.

Last updated: February 2026

For a Kenmore dishwasher model 58716169400, repairing is worth it when the problem is a leak, drain issue, or door sealing problem and the repair cost stays well below the price of a replacement. If you’re facing repeated major failures (motor, pump, or control issues), replacement is the better value.

Quick decision checklist

• If the dishwasher is under 10 years old, repairs usually make sense.
• If the repair is a single, clear failure (leak, won’t drain, won’t fill), repair is usually the best move.
• If you see water on the floor, start with door seals, hoses, and inlet components.
• If it won’t drain, check for a clog first; then consider the drain pump.
• If it fills slowly or not at all, the inlet valve is a common fix.
• If you’ve had multiple expensive repairs in the last 12 months, replacement is typically smarter.

Common repairs that are usually worth it on this model

Many “not cleaning” or “not draining” complaints trace back to water supply, loading, or a single failed part. The 58716169400 manual also points to basics like proper loading, incoming water temperature, and adequate home water pressure (typically 20 to 120 psi) as key performance factors; those checks can prevent unnecessary part replacement. Use the 58716169400 owner’s manual to match symptoms to the right troubleshooting steps.

Symptom	Most likely area	Typical outcome
Leaks at the bottom of the door	Door seal	Low-to-moderate cost repair
Won’t drain or leaves water	Drain path or drain pump	Often repairable
Won’t fill or fills slowly	Water inlet valve	Often repairable
Poor cleaning	Loading, spray path, water temp	Often no parts needed

Parts that commonly solve “repair vs replace” problems

If your issue matches one of these, repair is usually cost-effective:

• Door leak: gasket 809006501 (door seal, lower)
• Drain problems: hose 807117001 (drain hose) or dishwasher drain pump A00126501
• No fill/slow fill: valve 154637401 (water inlet valve)

Why it matters

A dishwasher that is mechanically sound but suffering from a leak, fill, or drain problem is typically a straightforward repair. Using the correct troubleshooting steps and the right Kenmore parts helps restore cleaning performance and prevents repeat failures.

Last updated: February 2026

Kenmore dishwasher model 58716169400 is a standard built-in dishwasher size: it fits a 24-inch-wide cabinet opening and is designed for a typical under-counter installation. For exact fit, we use the cutout and leveling measurements in the 58716169400 installation guide.

Key fit measurements to check

Measure your opening before ordering parts or scheduling installation:

• Width: Most built-in Kenmore dishwashers fit a 24-inch opening
• Minimum opening height: 33-3/4 inches (84.5 cm) (from underside of countertop to floor)
• Depth: Plan for a typical built-in depth range of about 24 to 26 inches, plus room for hoses and wiring
• Leveling: The unit must be level side-to-side and front-to-back for proper door sealing and draining

What the installation guide tells you (model-relevant)

The installation instructions for this Kenmore platform specify that if your opening height is at least 33-3/4 inches (84.5 cm), the dishwasher fits without modifying the countertop or flooring; leveling legs are adjusted to match the opening.

Quick checklist

• Confirm the countertop-to-floor opening height is 33-3/4 inches or more
• Verify the cabinet opening is 24 inches wide (standard built-in)
• Allow clearance behind the unit so the drain hose and wiring are not pinched
• Level the dishwasher to help prevent leaks at the door

Common size scenarios (what you are measuring)

Scenario	What it means	What to do
Opening height is 33-3/4 inches or more	Standard fit	Level the legs to match the opening
Opening height is tight	May require leg adjustment and careful positioning	Follow the leveling steps in the install instructions
Depth is limited	Hoses and wiring can bind	Leave extra space behind the unit

Why it matters

Correct sizing and leveling helps the door close evenly, supports proper draining, and reduces the chance of water escaping past the lower door seal. If you are chasing a small leak at the bottom edge of the door, the gasket 809006501 is a common wear item to inspect after confirming the dishwasher is level.

Last updated: February 2026