Frigidaire FFGF3051TSA gas range Parts

Your Frigidaire stove model number is printed on the appliance’s serial plate. On the Frigidaire gas range model FFGF3051TSA, the serial plate is typically found by opening the lower oven drawer or storage drawer; once you find it, copy the full model number exactly as shown.

Check these common serial plate locations on Frigidaire ranges:

• Open the lower oven drawer (or storage drawer) and look along the frame area
• Look on the drawer front frame after pulling the drawer out
• Check the oven door frame area (around the opening)
• Use a flashlight; the plate is often metallic and can be hard to read

Model numbers are a mix of letters and numbers, so accuracy matters.

• Write the model number exactly, including any suffix letters
• Watch for look-alikes like 0 (zero) vs O (letter) and 1 vs I
• Take a clear photo so you can zoom in and confirm characters
• Record the serial number too; it helps match production details for service

We use the model number to match the correct Frigidaire parts (like an oven igniter, control board, or burner components) and to pull the right diagrams and procedures from the FFGF3051TSA owner’s manual.

Last updated: February 2026

Yes. Looking up parts by model number is the most accurate way to get compatible replacement parts for your Frigidaire gas range, including model FFGF3051TSA. We recommend matching the full model and serial information from the appliance ID plate before ordering.

On this Frigidaire range, the identification plate is on the right-hand surface of the oven front frame. You access it by opening the storage drawer, warmer drawer, or broiler drawer (depending on your configuration). See the FFGF3051TSA installation guide.

• Write down the model number and serial number exactly as shown.
• Also note any lot number or letter listed on the ID plate.
• Confirm your range’s fuel type (natural gas vs. LP) and what it was adjusted for at the factory.
• Use the model number to filter parts by major sections (burners, ignition, oven controls, door parts).
• If you are replacing an ignition part, match by model first, then by symptom.

Model-number lookup narrows parts to the correct design revision for your range. That matters for items that look similar but fit differently, such as igniters, burner heads, and control components.

These are examples of parts commonly matched by model to ensure correct fit:

• Frigidaire range oven burner igniter 5304509706 (oven won’t heat or slow ignition)
• Range oven temperature sensor (temperature issues)
• Range spark module (surface burners won’t spark)

Using the exact model number from the ID plate prevents ordering a part that is close but not compatible, which saves time on returns and gets your range back to cooking faster. For additional model-specific guidance, use the FFGF3051TSA owner’s manual.

Last updated: February 2026

To remove the main top on your Frigidaire FFGF3051TSA gas range, we shut off the gas supply first, then remove the surface components (grates, burner caps, and burner heads) so the cooktop fasteners and lift points are accessible. Reinstall in reverse order and check for gas leaks.

• Turn all burner knobs to OFF.
• Shut off the external manual gas shut-off valve.
• Unplug the range (or switch off the circuit breaker).
• Let the cooktop cool completely.
• Protect the countertop and range finish with a towel or cardboard.

1. Remove the burner grates.
2. Lift off the burner caps.
3. Remove the burner heads (note their positions so they go back to the same burner).
4. Look for screws at the front lip or under the burner areas; remove any you find.
5. Lift the front of the main top, then slide it forward or prop it up (depending on hinge style).
6. If you need to disconnect wiring (igniters), label connectors and pull straight off.

Removing the main top the right way prevents cracked burner caps, misaligned burner heads, and pinched igniter wires, which can cause weak flames, delayed ignition, or constant clicking after reassembly.

• Confirm burner heads and caps sit flat and centered.
• Restore power, then turn gas back on.
• Test each surface burner for prompt ignition and steady flame.
• If the range was moved, check all gas joints for leaks using a liquid leak detector (never a flame) as described in the installation guide.

For diagrams, fastener locations, and any model-specific notes, follow the FFGF3051TSA owner's manual.

Last updated: February 2026