Installation guide
Owner’s manual
Error Codes
Does a Kenmore Elite have a reset button?
Kenmore Elite model 79031073100 does not use a single dedicated reset button. We reset the range by restoring power (unplugging or switching the breaker off, then back on) and then returning all oven and burner controls to OFF to clear a stuck control state.
How to reset your 79031073100 safely
- Turn all surface burner knobs to OFF.
- If the oven is running, press Cancel/Off (if your control has it), then confirm the display is idle.
- Switch the range circuit breaker OFF for 2 to 5 minutes.
- Switch the breaker ON and set the clock if prompted.
- Test a surface burner and then test Bake.
For model-specific control steps and normal operation checks, follow the 79031073100 installation guide.
What a “reset” fixes (and what it does not)
A power reset helps when the control is confused after a power flicker, the display is unresponsive, or a timed operation did not end cleanly. It will not fix ignition failures caused by a weak igniter, a bad sensor, or a gas supply issue.
| Symptom | Try reset? | Common next check |
|---|---|---|
| Display frozen or buttons not responding | Yes | Breaker reset, then retest functions |
| Oven will not ignite within about 60 seconds | Sometimes | Igniter glow and burner ignition cycle |
| Oven temperature seems inaccurate | Sometimes | Sensor resistance/connection |
| Surface burners click constantly | Sometimes | Burner cap seating and spark system |
If the oven will not light after resetting
The installation instructions note the oven may take 30 to 60 seconds to ignite after you turn it on. If it still will not light:
- Confirm gas shutoff valve is fully open.
- Verify the igniter glows; a weak igniter can glow but not open the gas valve.
- Check the oven temperature sensor connection.
- Inspect wiring for heat damage.
If you suspect an ignition component, the frigidaire range oven burner igniter 5303935066 and the range oven temperature sensor 5304504897 are common service parts for this model.
Why it matters
Resetting correctly prevents unsafe gas conditions and helps you separate a simple control glitch from a real ignition or temperature-control problem that needs parts or service.
Last updated: February 2026
How long should a Kenmore gas stove last?
A Kenmore gas range like model 79031073100 typically lasts 15 years with normal household use. Consistent cleaning, correct burner setup, and safe installation practices help you reach that lifespan and reduce ignition and heating problems.
Typical lifespan and what affects it
Most gas ranges land in a fairly tight range, but usage and maintenance make the difference.
- Typical gas range lifespan: 15 years
- Heavy daily cooking, frequent self-clean cycles, and poor ventilation can shorten life
- Keeping burner caps seated and ports clear helps prevent uneven flames and ignition strain
- Correct gas supply setup and grounding help protect controls and igniters
| Factor | Helps it last longer | Shortens lifespan faster |
|---|---|---|
| Cleaning | Regular degreasing, clear burner ports | Grease buildup, clogged ports |
| Cooking habits | Moderate temps, good ventilation | High heat daily, poor airflow |
| Installation | Correct gas hookup, grounded outlet | Loose connections, improper setup |
| Wear parts | Replacing igniters/sensors when weak | Running with failing parts |
Maintenance we recommend for 79031073100
Use the care and safety guidance in the 79031073100 owner's manual and keep these habits consistent:
- Clean spills promptly to prevent baked-on residue and smoke
- Remove and wash burner caps and bases; reinstall them aligned and level
- Keep the oven cavity reasonably clean so heat circulates normally
- Use a vent hood and clean its filter to reduce grease accumulation
- If ignition gets slow, address it early (weak igniters can stress gas valve operation)
When “it’s wearing out” vs. when it just needs a part
These symptoms usually point to a serviceable part, not the end of the range:
- Oven takes longer than 60 seconds to ignite after starting bake
- Surface burners click but light inconsistently
- Oven temperature swings more than normal baking tolerance
Common fixes for this model include replacing the frigidaire range oven burner igniter 5303935066 or the range oven temperature sensor 5304504897 when performance declines.
Why it matters
A gas range can run safely and cook evenly for its full expected life when ignition, flame quality, and temperature sensing stay in spec. Catching weak ignition or temperature issues early prevents bigger failures and keeps cooking results consistent.
Last updated: February 2026
What is the code F13 on a Kenmore Elite stove?
On Kenmore Elite gas range model 79031073100, an F13 display points to a control system fault that can interrupt oven operation. The most effective first step is a full power reset; if F13 returns, focus on wiring connections and the oven temperature sensing and ignition circuits.
Reset and verify power (do this first)
Use the safety and grounding steps in the 79031073100 installation guide before servicing.
- Turn all burner and oven controls OFF.
- Switch the range circuit breaker OFF (or unplug the power cord).
- Wait 60 seconds.
- Restore power.
- Set BAKE 300°F and watch for normal ignition.
What F13 usually involves on ranges
F-series codes are generated by the electronic oven control when it sees an out-of-range signal or a problem in a monitored circuit.
- Loose or oxidized connector at the control or sensor
- Damaged wiring harness (pinched behind the range)
- Oven temperature sensor circuit issue
- Ignition sequence problem that prevents stable heat
- Failed electronic oven control (after wiring and sensor checks)
Targeted checks for this model
The installation instructions describe the normal oven ignition sequence: the igniter glows, then the oven valve opens and the burner lights within about 30 to 60 seconds.
| What you observe | What to check next | Example part for this model |
|---|---|---|
| Oven heats erratically or shuts down | Sensor connection and sensor resistance | Range oven temperature sensor 5304504897 |
| No bake ignition (no flame) | Igniter glow and burner lighting sequence | Frigidaire range oven burner igniter 5303935066 |
| Igniter glows but no flame | Gas valve circuit and wiring | (test wiring and connections) |
Why it matters
An F13 condition means the control is not seeing a stable, correct signal for safe temperature control and ignition timing. Correcting the wiring, sensor, or ignition issue restores reliable baking and prevents repeat shutdowns.
Last updated: February 2026
What model is my Kenmore gas range?
Your Kenmore gas range model number is printed on a rating label attached to the appliance. On Kenmore Elite gas ranges like model 79031073100, the label is most often found in the oven door jamb area or behind the lower drawer.
Where to look first
Check these common label locations (in order):
- Open the oven door and look along the door frame (door jamb) on either side
- Pull out the bottom storage or broil drawer and look on the frame behind it
- Look on the back panel near the vent area
- Check the side panel near the front edge (visible when the door is open)
What the label looks like
The rating label typically includes:
- Model number (example: 79031073100)
- Serial number
- Gas type and pressure information
- Electrical rating (volts/amps)
- Certification markings
Use the exact model number from the label when ordering parts or checking fit in the 79031073100 owner's manual.
Quick tips so you do not miss it
- Use a flashlight and look for a white or silver sticker or metal plate
- Wipe grease or dust off the frame edge; the print can be faint
- If the drawer is heavy, remove contents first and slide it out fully
Why it matters
Kenmore ranges can look similar across multiple model series, but parts like the oven igniter, temperature sensor, and spark module vary by model. Matching the full model number helps us get the correct replacement the first time.
Common locations at a glance
| Location | How to access | Most common on ranges |
|---|---|---|
| Oven door jamb | Open oven door | Yes |
| Behind bottom drawer | Pull drawer out | Yes |
| Back panel near vent | Move range forward slightly | Sometimes |
Last updated: February 2026
Where is the model number on the Kenmore Elite stove?
On the Kenmore Elite 79031073100 gas range, the model and serial number plate is typically on the oven front frame behind the oven door, or on the drawer side frame. We use that plate information to match the correct parts and fuel setup.
Where to look on model 79031073100
Check these spots in order:
- Open the oven door and look along the front frame (the face frame around the oven opening)
- Pull out the storage/broil drawer and check the drawer side frame
- Look for a serial plate or rating label with model, serial, and burner/fuel information
For pictures and exact label locations for your unit, use the 79031073100 installation guide.
What the serial plate tells you (and why it matters)
The serial plate is more than a model number label; it also lists key configuration details that affect part selection and safe operation.
- Model number and serial number
- Burner ratings (BTU information)
- Fuel type (natural gas vs. LP)
- Gas pressure the range was set for at the factory
Quick reference
| What you need | Where it’s used | Why it matters |
|---|---|---|
| Model number (79031073100) | Parts lookup | Ensures parts fit your exact Kenmore Elite range |
| Serial number | Service history, production info | Helps match revisions and service bulletins |
| Fuel type and pressure | Installation and troubleshooting | Prevents ignition and flame problems |
Tips before ordering parts
- Copy the model and serial numbers exactly as shown on the plate
- If the label is greasy or faded, wipe gently with a damp cloth and mild cleaner, then recheck
- Keep the numbers handy when using the 79031073100 owner’s manual for operating and care details
Last updated: February 2026
Who makes Kenmore Elite gas ranges?
Kenmore Elite gas ranges (including model 79031073100) are made for Kenmore by major appliance manufacturers; the actual maker varies by model and production run. The most reliable way to identify the manufacturer for your specific range is to match the model and data plate details to the documentation in the 79031073100 owner's manual.
How Kenmore manufacturing works
Kenmore is a brand; it contracts manufacturing to different companies over time. For Kenmore Elite gas ranges, common manufacturers include:
- Electrolux/Frigidaire
- Whirlpool
- LG
- Samsung
How to identify who made your specific 79031073100
Use these checks to confirm the manufacturer tied to your exact unit:
- Look for the model and serial tag (often on the oven frame behind the door, or on a side frame).
- Compare the tag information to the parts and service information referenced in the 79031073100 installation guide.
- If you are ordering parts, match by model number first, then confirm by part number and part description.
- If your issue is ignition-related, confirm the symptom before ordering common parts like the frigidaire range oven burner igniter 5303935066.
Why it matters
The manufacturer affects parts compatibility, wiring layouts, and service procedures. Even when two ranges look similar, igniters, spark modules, and oven sensors can differ by production run.
Quick reference: what to use for what
| What you need | Best source to use | Why |
|---|---|---|
| Operating features, care, basic troubleshooting | 79031073100 owner's manual | Matches controls and normal operation for this model |
| Gas and electrical requirements, setup checks | 79031073100 installation guide | Covers installation standards and safety requirements |
| Correct replacement components | Model-based parts lookup plus part numbers | Prevents ordering a similar-looking but incorrect part |
Last updated: February 2026
Who makes Kenmore replacement parts?
Kenmore is a brand name, so replacement parts for our Kenmore Elite gas range model 79031073100 are typically manufactured by the original equipment manufacturer (OEM) that built the range and its components. In practice, that often means parts may be produced by major appliance manufacturers such as Whirlpool, Frigidaire/Electrolux, or GE, depending on the specific component.
How to make sure you get the right manufacturer part
The most reliable way to match the correct OEM part is to use your range’s model and serial information and then select parts by the Sears PartsDirect part ID.
- Find the model and serial plate on the oven front frame behind the oven door, or on the drawer side frame (varies by build)
- Match parts using the exact model number 79031073100
- Use the part ID on the parts listing to avoid mix-ups between similar-looking components
- Confirm fuel type and pressure info from the serial plate before ordering gas-related parts
- Follow the wiring and safety notes in the 79031073100 installation guide before servicing
Examples of OEM-style parts you can order for this model
These are common replacement parts for ignition and temperature control on model 79031073100:
| What it does | Part name (example) | Part ID |
|---|---|---|
| Lights the oven burner | Frigidaire Range Oven Burner Igniter | 5303935066 |
| Senses oven temperature | Range Oven Temperature Sensor | 5304504897 |
| Creates spark for surface burners | Range Spark Module | 5304508269 |
If you are troubleshooting a “no heat” or “won’t ignite” symptom, we often start with the igniter and sensor because they directly affect burner ignition and temperature regulation.
Why it matters
Kenmore parts sourcing varies by model and component. Using the 79031073100 model number plus the correct part ID helps ensure proper fit, safe operation, and correct gas and electrical compatibility.
Last updated: February 2026
