Electrolux EFLS210TIS00 washer Parts

On the Electrolux EFLS210TIS00 washer, error code E13 points to a leak condition that affects how the washer senses water level, most commonly water leaking into the base/outer tub area or an air leak in the pressure-sensing (air bell) system. Use the steps below to find the source safely.

What to check first (fast, high-success checks)

• Unplug the washer and turn off both water supply valves before inspecting.
• Look for water under the washer and along the front corners (door boot area) and rear (hoses).
• Check the drain hose for cracks, loose fit, or siphoning (hose shoved too far down the standpipe).
• Inspect the dispenser and fill hoses for drips during fill.
• Run a short rinse and spin while watching for leaks (only after panels are reinstalled and it is safe).

Common causes and what they look like

Likely cause	What you may notice	Typical fix
Loose or leaking inlet connections	Drips at the back during fill	Tighten/replace hose washers; reseat hoses
Failing inlet valve	Water seepage at valve body, overfilling symptoms	Replace the valve assembly
Door boot or door seal leak	Water at the front, especially during tumble	Reposition clamp, clean sealing surfaces, replace boot if torn
Internal hose or clamp leak	Water in base, intermittent leak	Re-seat/replace clamp or hose
Pressure-sensing air leak (air bell/pressure hose)	E13 with little visible external leaking	Reconnect/replace pressure hose; clear blockage

Parts that are often involved

If you confirm leaking or abnormal filling at the back during fill, the inlet valve is a common repair item for this model: washer 3-way water inlet valve 132518842.

Why it matters

E13 is not just an “annoying code”; leaks can damage wiring, the control area, and flooring. Fixing the leak source quickly helps prevent repeat errors and protects the washer’s electronic components.

Safety notes for DIY service

Follow the wiring-labeling and electrical safety guidance in the EFLS210TIS00 installation guide before opening panels or disconnecting any harnesses.

Last updated: February 2026

On the Electrolux EFLS210TIS00 washer, we reset most error codes by canceling the cycle and doing a power reset: press Power to stop, unplug the washer for 1 to 5 minutes, then restore power and start a new cycle. If the code returns, fix the condition that triggered it.

Quick reset steps (safe, no tools)

• Press Power to stop the cycle (this cancels the current cycle).
• Wait for the tub to stop moving before reaching inside.
• Unplug the washer for 1 to 5 minutes, then plug it back in.
• Press Power, select a cycle, and press Start.
• If the display shows door related messages, close the door fully and try again.

If the code comes back: what to check first

Many “reset” problems are really fill, door, or load issues. Check these common causes:

• Water supply: confirm both supply faucets are fully open.
• Fill problems: straighten kinked inlet hoses; make sure hoses are installed correctly.
• Door/lock: close the door firmly; the washer will not run with the door open.
• Unbalanced load: stop the washer and redistribute the load in the drum.
• Overheated motor: if the motor overheats, it can stop and restart after a cool-down (up to about 30 minutes).

Symptom-to-check table

What you see	Most likely cause	What to do
Won’t start after reset	Door not fully closed, power issue	Close door, verify outlet/breaker, retry
“Check the tap” or slow/no fill	Water supply or inlet restriction	Open faucets, unkink hoses
Stops or won’t spin	Small/unbalanced load	Add similar items, redistribute

When a part is the likely fix

If you have repeated fill-related errors after confirming faucets and hoses, the inlet valve can be the root cause. For EFLS210TIS00, we match the correct replacement by model: washer 3-way water inlet valve 132518842.

Why it matters

Clearing the code without correcting the underlying issue usually makes the error return and can leave clothes soaking wet or prevent the washer from starting. A quick reset plus basic checks solves most repeat codes.

For control panel button sequences and any model-specific display messages, follow the steps in the EFLS210TIS00 owner's manual.

Last updated: February 2026

Electrolux washing machines typically last 10 years. For the Electrolux EFLS210TIS00, that 10-year expectation lines up well with the long-coverage components called out in the EFLS210TIS00 owner’s manual, including extended coverage on the wash tub drive motor.

Typical lifespan (what we see most often)

Most front-load washers, including Electrolux models like EFLS210TIS00, deliver about a decade of service when they are installed correctly, used with the right detergent amount, and maintained (especially keeping odors and moisture under control).

What most affects lifespan:

• Load size and frequency (daily heavy loads shorten life)
• Proper installation (leveling, correct drain standpipe height)
• Detergent type and dosage (HE detergent, no over-sudsing)
• Moisture control (door gasket and drum kept clean and dry)
• Early repair of small issues (leaks, fill problems, vibration)

Warranty coverage vs. life expectancy

Warranty is not the same as lifespan, but it helps show which components are designed for long service.

Item	Coverage noted for EFLS210TIS00	What it means for you
All parts	1 year (with additional parts-only coverage into year 2)	Most early failures show up here
Wash tub drive motor	10 years (excluding labor)	Motor is built for long-term use
Wash tub	Functional life of the product (excluding labor)	Tub is intended to last the washer’s usable life

How to help your EFLS210TIS00 reach (or beat) 10 years

• Keep the washer level to reduce vibration and bearing wear
• Use the correct drain setup; a standpipe that is too low can cause siphoning and poor fills
• Run periodic cleaning cycles and wipe the door boot/gasket dry
• Avoid chronic overloading; it strains the drive system
• Address fill issues early; a failing inlet valve can cause slow fill or temperature problems

Why it matters

A washer that is maintained and installed to spec tends to avoid the most expensive wear points (motor strain, excessive vibration, and moisture-related odor or residue). Following the setup and care guidance in the EFLS210TIS00 installation guide is one of the simplest ways to protect long-term reliability.

Last updated: February 2026