Owner’s manual
Error Codes
Where is the model number on a Kenmore side by side refrigerator?
On Kenmore side-by-side refrigerator model 10657029600, the model number is printed on the appliance identification label (the same label typically lists the serial number). We use that model number to match the correct parts, diagrams, and troubleshooting info in the owner's manual.
Look for a paper or foil label in one of these spots:
- Inside the fresh food compartment on a side wall (often near the crisper area)
- On the ceiling of the fresh food compartment near the light
- On the door frame around the fresh food door opening
- Inside the freezer compartment on a side wall
- Behind the base grille or near the lower front frame (less common)
The label usually includes both a model number and a serial number.
| Item on label | What it’s used for | Example for this page |
|---|---|---|
| Model number | Identifies the exact refrigerator design for parts fit | 10657029600 |
| Serial number | Identifies the production unit and date code | Varies by unit |
Kenmore refrigerators can look similar across multiple model series. Using the exact model number (like 10657029600) prevents ordering the wrong water filter, ice maker, door gasket, or control part.
- Copy the model number exactly as printed (all digits, no spaces)
- Take a photo of the label for reference
- If the label is worn, gently clean it with a damp cloth and dry it
Last updated: February 2026
What are the most common problems with Kenmore refrigerators?
The most common issues we see on Kenmore refrigerators like model 10657029600 are cooling complaints (warm fridge or freezer), ice maker and water dispenser problems, moisture buildup, and “noisy” operation that is actually normal. Many symptoms trace back to airflow, door sealing, or water supply conditions; see the owner's manual troubleshooting section for model-specific checks.
- Not cooling or weak cooling: doors left ajar, heavy food load, warm room, blocked vents, or dirty condenser area
- Runs “all the time”: high-efficiency compressor and fans can run longer, especially with frequent door openings
- Noisy operation: buzzing, pulsating, rattling, sizzling, popping, and water-running sounds can be normal during cycles
- Ice maker not making ice: shutoff valve closed, kinked water line, ice maker switched off, or new install not fully cycled
- Water dispenser issues: warm first glass, low flow from supply restrictions, or filter-related flow reduction
- Moisture or frost: humid room air, doors opened often, or door seal not closing tightly
- Confirm the controls are ON and give the refrigerator 24 hours after installation or major adjustments to stabilize.
- Check that doors close fully and nothing is holding them open.
- If ice is low, verify the household shutoff valve is fully open and the water line is not kinked.
- If dispenser water is not cold, remember dispenser water is typically chilled only to about 50°F (10°C).
- Reduce door openings for a day and recheck temperatures.
| Symptom | Most common cause | What to do next |
|---|---|---|
| Warm temps after setup | Normal stabilization time | Wait 24 hours, then recheck |
| Motor runs a lot | High-efficiency design, warm room, frequent openings | Minimize openings; recheck in 24 hours |
| Ice maker slow/no ice | Water supply off, kinked line, ice maker off | Open valve, straighten line, turn ice maker on |
| Moisture inside | Humidity, doors opened often | Keep doors closed; wipe moisture |
| Buzzing/popping/sizzling | Normal operating sounds | Compare to normal sound list in manual |
Catching simple causes early (door sealing, airflow, water supply) prevents food temperature swings, reduces ice and water interruptions, and avoids unnecessary part replacement.
Last updated: February 2026
Where is the filter located on a side by side refrigerator?
On Kenmore model 10657029600, the water filter is located in the base grille below the freezer door. You remove it from the front by pressing the eject button and pulling the filter straight out (the base grille does not need to be removed). See the owner's manual.
- Look at the bottom front of the refrigerator, under the freezer door.
- Find the base grille opening with a filter cap visible.
- Locate the eject button next to the filter cap.
- Pull the filter straight out after pressing eject (avoid twisting).
- Press the eject button.
- Pull straight out on the filter cap and cartridge.
- Turn the cap counterclockwise to remove it from the old filter.
- Install the cap on the new filter; align the ridge on the cap with the arrow on the filter.
- Push the new filter into the base grille opening until it seats.
| What you notice | Usually means | What we recommend |
|---|---|---|
| A little water drips when you remove the filter | Normal | Keep a towel handy |
| Cap wants to come off while pulling | You twisted the cap | Re-seat the cap, then pull straight out |
| Water flow is weak at dispenser/ice maker | Filter is clogged or overdue | Replace the filter cartridge |
Knowing the filter location helps you replace it on schedule and restore normal water flow to the dispenser and ice maker. For this model, we recommend replacing the filter about every 6 months, or sooner if flow drops.
Related part for this model: If you need the replacement cartridge, use the genuine Kenmore refrigerator water filter EDR3RXD1.
Last updated: February 2026
