Kenmore 58714249990 built-in dishwasher Parts

Yes. You can still get replacement parts for a Kenmore dishwasher, and for model 58714249990 many common repair parts are available by matching the exact model number to the correct component in the parts list and diagrams in the 58714249990 owner's manual.

How to make sure you get the right part

Use the model number first, then confirm the part by location and symptom.

• Match the full model number: 58714249990
• Compare the part name and where it installs (door, tub, sump, rack)
• Check your symptom (no fill, leak, won’t drain, door won’t latch)
• Verify any included hardware you may also need (screws, clamps, nuts)
• If your dishwasher is older, focus on high-failure items first (valves, seals, door parts)

Common parts people replace on this model

These are typical “wear” or “failure” items that often solve everyday dishwasher problems.

Problem you see	Part category to check	Example part for this model
Won’t fill or fills slowly	Water inlet components	Water valve 154637401
Door won’t close or pops open	Latch/strike hardware	Door strike 154662601
Rack won’t roll smoothly	Rack wheels/stops	Dishwasher wheel 5304532229
Leaks at the tub opening	Seals and gaskets	Dishwasher tub gasket 8581548276014

Why it matters

Kenmore dishwashers are built with serviceable components, so the correct OEM-style replacement part usually restores normal washing, filling, draining, and door sealing without replacing the entire dishwasher.

Last updated: February 2026

On the Kenmore dishwasher model 58714249990, an E25 error points to a drain problem, most often a blocked drain pump area or an issue with the pump cover/filter area that keeps water from pumping out normally. For model-specific operating and care details, use the 58714249990 owner's manual.

What to check first (fast, no parts)

• Turn off power at the breaker before reaching into the sump area.
• Cancel the cycle and see if the unit attempts to drain (listen for the drain pump).
• Check the bottom of the tub for standing water and remove any debris.
• Inspect the drain path: filter area, sump inlet, and drain hose routing (no kinks or crushing).
• Verify the sink/disposer connection is clear (common clog point).

Common causes and what they look like

Likely cause	What you notice	What to do
Debris in sump or pump inlet	Water remains in tub; humming during drain	Remove debris; clean sump area
Drain hose restriction/kink	Intermittent draining; slow drain	Straighten hose; clear blockage
Float stuck (overfill protection)	Odd fill behavior; may stop filling or act erratic	Clean float so it moves freely
Drain pump not moving water	Pump runs but no drain flow	Check for obstruction; test pump circuit

Parts that can be involved

If the dishwasher is not draining because the water level sensing is incorrect, the float system is worth checking. The float should move up and down freely; cleaning buildup helps prevent sticking.

If you find the float switch is damaged or not switching reliably, the correct replacement for this model is the dishwasher float switch 154225501.

Why it matters

When the dishwasher cannot drain, it can pause the cycle, leave dirty water in the tub, and reduce wash performance. Clearing the drain path early prevents repeat errors and helps protect the pump and motor.

Last updated: February 2026

If you’re on this model page, you have a Kenmore built-in dishwasher model 58714249990. To confirm on the appliance itself, open the door and look for the model/serial label on the inner door frame, along the tub rim, or on the tub wall; match it exactly to 58714249990. See the 58714249990 owner's manual for label location and model-specific details.

Where to find the model number label

Check these common spots first (door open):

• Inner door frame (left or right side)
• Top edge of the door opening (tub rim)
• Inside the tub on a side wall near the front
• Along the bottom edge of the door
• Behind the lower access panel (if the label is missing inside)

How to confirm you have the right “kind” of dishwasher

Kenmore dishwashers are best identified by the full model number, not just the brand name. Use this quick checklist:

• The label says 58714249990 (exact match, no extra digits)
• It’s installed under a countertop (built-in style)
• Parts diagrams and parts like the water valve 154637401 match what you see under the unit

Why the exact model number matters

The model number controls which parts, wiring, and features your dishwasher uses. Even small differences can change fit and function for items like the water inlet valve, float switch, door strike, or control panel.

Quick reference table

What you’re checking	What to match	Why it matters
Model number	58714249990	Ensures correct parts and troubleshooting steps
Serial number	Unique to your unit	Helps identify production details and service history
Product type	Built-in dishwasher	Confirms installation style and compatible hardware

Last updated: February 2026