Kenmore Elite 59677593801 bottom-mount refrigerator Parts

Yes. For Kenmore Elite model 59677593801, the most reliable reset is a power reset: unplug the refrigerator (or switch the breaker off) for about 5 minutes, then restore power and allow the controls to reboot. For the water filter indicator, use the built-in Filter Reset control.

Quick reset options (most common)

• Power reset (control reboot): Unplug for ~5 minutes, then plug back in.
• Breaker reset: Turn the refrigerator circuit breaker off for ~5 minutes, then back on.
• Water filter light reset: Press and hold Filter Reset for 3 seconds until the Replace light turns off (on models with this feature). See the 59677593801 owner's manual.
• Temperature alarm reset (silence/clear display): Press Temp Alarm once to stop the audible alarm; the light can keep flashing until temperatures return to normal.
• After any reset: Confirm doors close fully and air vents are not blocked by food packages.

When a reset helps (and when it does not)

A reset is best for control glitches, a stuck filter light, or after a brief power interruption. It will not fix a failed cooling component (like a compressor start issue) or an airflow problem caused by heavy frost.

Situation	Best action	What to expect
Control panel acting odd	Power reset	Display and controls reboot
“Replace” filter light on	Filter Reset (3 seconds)	Light turns off if feature is present
Temp alarm sounding	Press Temp Alarm once	Alarm stops; light may flash until temps recover
Not cooling after reset	Basic checks, then diagnosis	May point to fan, defrost, or sealed system issue

Why it matters

Resetting clears temporary control-board states so the refrigerator can resume normal temperature regulation, ice maker timing, and filter tracking. It also helps you separate a one-time glitch from a real cooling or defrost problem.

If it still will not cool after resetting

• Make sure the outlet has power (test with a lamp).
• Verify the controls are turned on.
• Allow 24 hours after restoring power for temperatures to stabilize.
• Listen for the evaporator fan in the freezer and check for heavy frost buildup.
• If you suspect a fan issue, the refrigerator evaporator motor W11024089 is a common related part on this model.

Last updated: January 2026

On Kenmore Elite refrigerator model 59677593801, DH commonly indicates a defrost heater issue (the unit is not heating properly during the defrost cycle), which can lead to frost buildup and warm temperatures. Use the troubleshooting steps in the 59677593801 owner's manual to confirm symptoms and safe checks.

What you’ll usually notice when DH shows up

• Frost or ice building up on the freezer back wall
• Freezer temperature slowly rising
• Refrigerator section getting warmer than normal
• Evaporator fan noise changing as airflow gets restricted
• Water leaking or refreezing near the freezer floor after a defrost attempt

Quick checks we recommend first (safe, no disassembly)

1. Power reset: Unplug the refrigerator (or switch off the breaker) for 5 minutes, then restore power.
2. Airflow check: Make sure vents are not blocked by food packages.
3. Door seal check: Look for gaps, rips, or areas not sealing flat.
4. Condenser cleaning: Vacuum dust from the condenser area if accessible.
5. Temperature settings: Return controls to normal settings if they were changed recently.

Parts that commonly cause a DH (defrost heat) problem

If the code returns after a reset and airflow is good, the issue is typically in the defrost circuit.

What can fail	What it does	Example part for 59677593801
Defrost heater	Melts frost off the evaporator	Refrigerator defrost heater WP67002493
Temperature sensor	Tells the control when to defrost and when to stop heating	Refrigerator temperature sensor 12002355
Wiring/connector	Carries power to heater and sensor	Inspect for loose or burned terminals

Why it matters

A defrost heater problem reduces airflow across the evaporator coil. That forces longer run times, causes temperature swings, and can eventually stop cooling well in both compartments.

Last updated: January 2026

On Kenmore Elite model 59677593801, the temperature sensor (thermistor) is typically mounted inside the fresh food compartment or freezer compartment near an air vent or on the evaporator area behind an interior panel. Use the 59677593801 owner's manual to match the sensor location to your exact compartment layout.

Common sensor locations on bottom-mount refrigerators

On this style of Kenmore Elite bottom-mount refrigerator, we most often see temperature sensors in these spots:

• Behind the rear interior panel in the freezer, clipped near the evaporator coil
• In the refrigerator section, tucked into a small housing near the upper back wall air return
• Near the control housing (depending on control style), sensing compartment air temperature
• In the freezer airflow path, close to the evaporator fan cover

How to find it safely (quick checklist)

Before removing panels or testing parts:

• Unplug the refrigerator or switch off power at the breaker
• Empty the area you are working in (shelves, bins, baskets)
• Look for a small plastic “bullet” or capsule-shaped probe with two wires
• Follow the wire harness from the control area or rear panel toward the air vents
• Take a photo of wire routing and connector positions before disconnecting anything

When the sensor is the likely problem

A failed or out-of-range thermistor can cause symptoms that look like control issues:

Symptom	What it often points to
Refrigerator too warm but freezer OK	Refrigerator air sensor or airflow restriction
Freezer too warm and ice soft	Freezer sensor, defrost issue, or evaporator frost buildup
Temps swing up and down	Sensor reading drifting or poor sensor contact
Alarm sounds after temps rise	Compartment temperature exceeded set point

If you are troubleshooting temperature problems, we also check for blocked vents and allow 24 hours after any control change for temperatures to stabilize (as described in the manual).

Parts that are commonly involved in temperature-sensing problems

Depending on what you find during diagnosis, these parts are often checked together:

• Refrigerator temperature sensor 12002355 (sensor itself)
• Evaporator fan motor (air movement across the evaporator)
• Defrost heater (frost control on the evaporator)

Why it matters

The control board relies on the temperature sensor signal to decide when to run the compressor and fans. If the sensor is loose, iced over, or electrically out of range, the refrigerator can run too long, not long enough, or trigger temperature alarms.

Last updated: January 2026